✅ HOW TO SUPPORT MY CHANNEL SUBSCRIBE : kzitem.info JOIN my Patreon community: patreon.com/MWAWoodworks GET project plans: bit.ly/download-project-plans ✅ TOOLS AND SUPPLIES IN THIS VIDEO: Centipede Work Holder - bit.ly/bora-centipede True Position Tools Cabinet Hardware Jig - amzn.to/3g3pgDr Kreg Shelf Pin Jig - amzn.to/3Oc6O9V Kreg Concealed Hinge Jig - amzn.to/3uOsyBV Kreg Pocket Hole Jig - amzn.to/3P9rH6S Mag Switch - amzn.to/3PqmasA Bessey One Handed Clamps - amzn.to/2VWftbp Plywood Router Bit Set - amzn.to/3sj7lxn Fast Setting Wood Glue - amzn.to/3RHbuHC Paste Wax (for screws) - amzn.to/3AOd41r Self Centering Drill Bit - amzn.to/3yNNpFx Castle TSM-12 pocket cutting machine - bit.ly/castle-tsm-12-pocket-cutter *As an Amazon Associate I earn from qualifying purchases
@romanjakusz1991
Жыл бұрын
the author does like to from scratch, shaping and trimming wood from large blocks into fine finished products. kzitem.infoUgkxD-QRFQz730FJEh4f9BYSf-nkIMIC9hL_ as another reviewer mentioned, most projects require a lot of high-dollar equipment that most of us dont have the room or budget for. But, knowing how to do these things, even if we wont be able to practice the full stack project, is still great.
@firerescue3214
Жыл бұрын
Did you end up putting a finish on all the door frames or did you leave it raw wood?
@noegutierrez6463
Жыл бұрын
thank u for shearing very goos information.
@turbo-jm8hk
3 жыл бұрын
where u located and how long does it take you to make a set of kitchen cabinets
@DerekTJ
Жыл бұрын
Need an apprentice? I'm only 51.
@iainarthur7713
3 жыл бұрын
Looks great. Minor issue in the UK is that ply that looks that good would require the sale of a kidney....:)
@barrytipton1249
3 жыл бұрын
In the US, the price of that piece of plywood would also cost you a kidney. 🤣
@jodiepalmer2404
3 жыл бұрын
Here in Australia, it will be a miracle to get plywood that good and also close to $300 a sheet. Even then it will take more than a kidney to buy one.
@SevenSinsChoppers
Жыл бұрын
Where do you get that plywood with that nice coated satin finish?
@ricklowery9369
3 жыл бұрын
This wonderful video is about 3 days too late. ;) I bought wall cabinets for my shop at HD and put them up on Saturday. I would have much preferred making my own. But thanks for the great video.
@luisfaustino
3 жыл бұрын
Great video thanks. How do you install the cabinets on the wall?
@evanbeck3326
10 ай бұрын
I see you are using pre-finished maple plywood which makes everything much easier. However, are you not putting any finish on the face frames or doors?
@DonnieKluck
Жыл бұрын
Matt or anyone, so I bought the Whiteside Undersized Router Bits. However when I cut my DADOs yesterday, I went to try to fit my 1/4 and 3/4 birch plywood in the grooves and they would not fit. I tried my test nailer piece (piece I used to test the groove depth, etc) and it fit in like a glove. But my actual pieces for the cabinet itself would not fit. I tried to gentle tap it but it started to crack and push/peel up the vneer. Is there a reason for this? What is the best way to get it to fit? Only thing I could think was try a pass on the table saw to trim off like 1/64. But still dont understand why some other pieces of plywood fit and the actual cabinet pieces dont.
@MWAWoodworks
Жыл бұрын
Sometimes plywood will have varying thickness. This can even happen with different parts of the same sheet of plywood.
@DonnieKluck
Жыл бұрын
@@MWAWoodworks Really, I would not have thought that. I figured if it was all from the same stock it should be the same. But that makes sense. Thanks I have to work on making it fit, and to think I thought this would be the easy part LOL
@GarlandLym
2 жыл бұрын
The one thing I never see a video on : How to measure: 1. How much lip on face frame 2. Where to source quality cabinet wood 3. How to measure offsets for hinges with respect to door width 4. How to measure door and drawer heights to creat 1/8” gaps 5. How to easily measure for equal drawer heights Fantastic video. I understand the need for exacting content, but maybe make some smaller videos (tips) to address the little in between info
@boonvang708
Жыл бұрын
I think it's because you missed it...I had to rewatch a lot of his videos over but he either says it or shows it...sometimes its fast if you blink you will miss it Idk about sourcing wood but sure anyone wouldn't have an issue with this
@baerfas
Жыл бұрын
I agree. He should cover these points on more videos.
@MCsCreations
3 жыл бұрын
Beautiful work, Matt! Really well done! 😃 Thanks a lot for all the tips!!! Stay safe there with your family! 🖖😊
@MWAWoodworks
3 жыл бұрын
Thanks brother 😁
@walnut_trail_farm
2 жыл бұрын
Great video! Question - if you were doing a more modern cabinet door that was completely flat, could you simply use a piece of plywood with edge banding around it? Or is it better to use actual wood joined together? Thanks!
@billyswoodshop9063
2 жыл бұрын
Yes most flat doors are edge banned plywood
@justinkornhaus1445
3 жыл бұрын
Glad to see your channel is growing. You’re definitely one of the best woodworking channels out there.
@philipwilson9209
Жыл бұрын
I've been looking for the best way to make wall cabinets for days now. This video is really helpful to me. I've been wood working for about 40 years and made a lot of free standing cabinets and shop cabinets, but not kitchen wall cabinets. The video answered several questions I had. Nice job. Now I'll use these methods to build my new kitchen cabinets our of African Mahogany. 👌👍
@CCoburn3
2 жыл бұрын
Gotta love a "woodworker" who makes "how-to" videos using tools that no one except professionals can afford. It's worse than Norm Abram having so many routers that he never had to change a bit.
@MWAWoodworks
2 жыл бұрын
I'm not a professional woodworker. I work out of my own home workshop and was able to afford these tools slowly over the last 10 years 🤷
@Mark-bn7lk
8 ай бұрын
Is 3-quarter plywood necessary for upper wall cabinets or could you use half-inch plywood instead? The reason I ask is that on my high-end kitchen cabinets, the carcass seems to be half-inch plywood. I would appreciate your thoughts on this. Thanks for a really informative video.
@MrMcQuade
Жыл бұрын
This was nice and concise. I enjoy the lack of fluff/filler. I was thinking of doing pocket holes and adding some dowel along the joints as well for some extra support. I’m using 3/4in aspen plywood for the whole thing(that’s all I have). This is just a garage cabinet. I’m hanging it using a top and bottom French cleat system. What is a good way to get some extra support when attaching the French cleat mounting pieces? I was think of ripping some 2x4 into 1in strips and putting them flush with the back edge of the cabinet so that the back panel will mount on as it should. I think that should do it, no? It take up a small amount of the interior space of the cabinet, but as I mentioned, this just a shop cabinet.
@Tman317
27 күн бұрын
Great videos and I actually bought your plans. My question that I can't figure out:At 12:23, you can see a larger gap between doors of.the two cabinets (the right-most two). Is there any way to make this gap smaller and consistent across the entire set of doors in a bank of cabinets? I can't figure out the right stile width, hinge overlay, hinge type, etc. to make it happen!
@brucelavis4934
Жыл бұрын
Nobody but nobody addresses the issue of shop dust covering the French cleat items. Cabinets with sliding doors will solve the problem. Use lexan for visibility. Your thoughts. Better yet build one and make the video!!!! Thx
@PepperLion
Жыл бұрын
At $1,775 I imagine the pocket hole cutter is amazing, but it prices out the average woodworker. I imagine if you're a cabinet maker that would pay for itself.
@abelhuet
3 жыл бұрын
Just great!! so easy and nice that i'm gonna make some for my little shop. Greetings from Puerto Vallarta, México
@MWAWoodworks
3 жыл бұрын
Thanks Abel! Glad I can inspire you to upgrade your shop organization!
@boonvang708
Жыл бұрын
I absolutely love this channel! I'm a welder by profession...but recently I've been trying to get into wood working and building a wood working shop in my basement. 1st I will try and build cabinets for my garage and if that turns out really good I will try my hand at building cabinets for my kitchen. Love this channel
@MWAWoodworks
Жыл бұрын
Thanks for your support!
@joedance14
2 жыл бұрын
Nice video. I like your use of traditional joinery. Demonstrating the alternative, pocket holes, is a nice touch, helping to provide perspective to inexperienced woodworkers. Q: how deep are these cabinets? I have read that upper cabinets are usually one or two feet deep. I need to build a saw till and a plane till, and neither needs to be more than a foot deep. To protect the tools from humidity and dust, I was thinking of using cabinets like these, rather than a traditional open style till. I was thinking of building a couple more cabinets for storage, and consistent appearance would be nice as well. Any thoughts or suggestions would be most appreciated.
@GReddy2319
Жыл бұрын
Standard wall cabinets are 12" deep, though 15" has become significantly more common due to the current age of larger dishware. Keep in mind, standardized measurements for cabinets are taken from the front of the cabinet face frame (not the door) to the rear back of the cabinet. Once you take out the 3/4" face frame and then 3/4"-1" for the rear panel and hangars (depending on if you use 3/4" or 1/2" blocks), you end up with 1 1/2"-1 3/4" less usable space. The decision is ultimately up to the end user on the depth that they would prefer, but the deeper the wall cabinet, the less counter space that will be visible when standing at the counter (or workbench). Many people in show cabinets will go deeper than 15" due to the higher need for storage and sometimes higher mounting height from the base cabinet or workbench.
@joedance14
Жыл бұрын
@@GReddy2319 Thanks!
@josephvondauber9327
3 жыл бұрын
Very impressive work. You make it look so easy!
@MWAWoodworks
3 жыл бұрын
Thanks for the kind words!
@DonnieKluck
Жыл бұрын
Matt two questions for you, 1) you use the paste wax just to put on screws to help them drive into the wood? And 2) what filler/putty do you recommend for filling in the holes from the brad nails I used to secure the face frame to the cabinet?
@MWAWoodworks
Жыл бұрын
1)Yes 2)I don't have a preferred wood filler, just whatever the big box carries
@DoNnEgRoW
8 ай бұрын
hi, how would i not have that 3/4" gap from underneath the back panel to the wall ? and if i keep that back panel land on the bottom panel i will the the dado, thanks
@trevormyers8798
2 жыл бұрын
You make the best how to videos, thank you for the great information!
@MWAWoodworks
2 жыл бұрын
Thanks!
@SpencleyDesignCo
3 жыл бұрын
This is an EXCELLENT reference video! Thanks, Matt!
@dusbus2384
Жыл бұрын
I used this exact method of building my cabinets for laundry room using the traditional style. Two issues i had were the undersized bit was still bigger than the plywood making a sloppy dado. I ended up having to make two passes with an 1/8" but and sneak up on it. The other thing i did different was cut a 45 degree edge on my top back nailer. I then was able to hang the cabinet on the wall with another 45 degree piece i screwed into the wall. A french cleat. This made hanging the cabinets super easy with no ledger board required and no wall patching
@MWAWoodworks
Жыл бұрын
❤️
@Italianfoodtours
3 жыл бұрын
great video! thank! wanted to buy some staff from amazon, but none of the links works... ):
@MWAWoodworks
3 жыл бұрын
Links are working fine 👍
@tlough1
Жыл бұрын
Tried to buy your plan but my antivirus says there is a Trojan virus on your site
@MWAWoodworks
Жыл бұрын
Definitely no Trojans or any other viruses on my site! Sometimes antivirus programs get confused. You can also go to gumroad.com/mwawoodworks and buy my plans on that site too.
@alsprettycreations8005
2 жыл бұрын
Nice work, I build my wall cabinetry with 45-degree beveled back hang rails ( French cleats ) it makes it so much easier when it come to installing.
@MWAWoodworks
2 жыл бұрын
Ah yeah I fasten mine like kitchen cabinets
@pto200
3 жыл бұрын
Good job and great video. You make it look easy. Thanks.
@bryanharness1122
Жыл бұрын
for simple pocket screw assembly. you can move top and bottom in 3/4" and end up with same void area for screws or lighting. i like the dados myself. feels and looks stronger to me.
@MWAWoodworks
Жыл бұрын
Thats true but the pocket screws afford you to have an inch and a half more space inside the cabinet, which for shop cabinets is nice to have.
@bryanharness1122
Жыл бұрын
@MWAWoodworks true. So many options. Great video btw
@jessemarquez
23 күн бұрын
Good content, but nOt every DIYer has access to this kind of setup to work with 🤦🏻♂️
@MWAWoodworks
23 күн бұрын
I'm aware that not every DIYer has this setup. That's why I made the video to show DIYers what kind of setup they should get 😁
@rudyswoodwork7236
3 жыл бұрын
Great build what’s the name of pocket machine I’m interested on buying one
@MWAWoodworks
3 жыл бұрын
It's a Castle TSM 12
@adamjonkie5601
Жыл бұрын
Do you have sponsors for wood?!i see so many channels using 3/4 plywood. I looked at Home Depot and sanded 3/4 plywood was $80 a sheet.
@MWAWoodworks
Жыл бұрын
Nope I pay just like everyone else 😊
@kmsand5905
2 ай бұрын
Can you please tell me what bolts/screws you used to attach upper cabinets to cinder block. I have been afraid to build and install myself.
@MWAWoodworks
2 ай бұрын
Tapcons
@kdcustomwoodworking
Жыл бұрын
Your production of your videos are amazing hoping to get that good .Only tip use full 3/4backs saves time and money ,that's a lot of steps for the back also the back is the spine of the cabinet needs that 3/4 strength..
@Edwardbwalti
Жыл бұрын
Nice showing how you make cabinets but I would like to try this for myself and you don't give dimensions on your panels and stuff. 😢
@MWAWoodworks
Жыл бұрын
Yes I do. In the plans!
@MrPatdeeee
3 жыл бұрын
Awesome. I shall follow it when I make my cabinets. Thank you kind Sir.
@MWAWoodworks
3 жыл бұрын
Awesome 😎 thanks Pat!
@bruceweller6391
2 жыл бұрын
Great video Matt. I was curious when you built the cabinet doors to size and then shaved the top and bottom to clean them up on the cross-cut sled. Question - did you account for that when you cut your rail and stile before assembly or was the "shaving" so negligible that you didn't account for it? I've struggled on occasion to have my end joints crisp and clean after assembly and this was a great option. Just wasn't sure if I needed to account for any additional math before I commit this to my next build. Thanks for sharing ....
@MWAWoodworks
2 жыл бұрын
Yes I always leave 1/8" all around my doors. This allows me to fit them perfectly and also cut off any glue that squeezed out of the joints 👍
@paulocmunoz
3 жыл бұрын
Great video MWA I really like the miter saw station do you have plans for sale?
@MWAWoodworks
3 жыл бұрын
Soon! Working on plans now
@zephyr1408
3 жыл бұрын
How come you do not use that nice router for a stick & cope joint on the doors? I can make two to one using that method as opposed to a stub tendon door? I make my custom cabinets that way with a domino in the joint if customer wants reinforced doors (kids👊). Rocklers S&C bits are the best I used! I gotta invest in that castle PH machine what a sweet tool! Thanks for the video I know it’s time consuming!
@MWAWoodworks
3 жыл бұрын
I do that as well but many people have not invested in a nice router table so I show them how to do the same thing on a table saw 👍
@zephyr1408
3 жыл бұрын
@@MWAWoodworks understand Thk u for the answer makes sense !!
@darthr01g41
3 жыл бұрын
Sorry, not sorry. I couldn't even finish watching with that annoying background "music". It's like I'm trying to watch a video but hear my neighbor playing indistinguishable "music". Annoying af!
@jupiterjac6438
2 жыл бұрын
PLEASE HELP : looking for some ideas on how to secure melamine cabinets on a wall that has plywood behind it ! My backing for cabs is 3/4 thick I would assume sheetrock is 1/2 and plywood half inch or 3/4 I usually use 3” screws on walls without the plywood directly to studs ANY IDEAS help any info on certain wood screws anything !! Was just thinking to use longer screws and put a bunch on each cabinet for extra strength TIA!! I was also thinking I might add some legs on it but my goal is for it to be floating , thanx!!!
@Spratlyk9
2 жыл бұрын
Did you use a quarter inch (real quarter inch) plywood for the door panels? I asked because most of the quarter inch plywood are not really quarter inch, so when I use my shaker door router bits to cut the grooves, the quarter inch panels are too loose to fit on the rails and stiles. What do you recommend? Thanks for posting your videos and more power to your channel!
@MWAWoodworks
2 жыл бұрын
I used 1/2" for the panels and cut a rabbet around all four sides to fit into the frame.
@Spratlyk9
2 жыл бұрын
@@MWAWoodworks Thank you!
@jonnyboy1116
2 жыл бұрын
@@MWAWoodworks is there a reason why you used 1/2 inch plywood with rabbets instead of 1/4 inch plywood for the door panels? It just seems like unnecessary added weight and added steps to cut the rabbets unless I'm missing a technical reason.
@harrisonbullard9845
8 ай бұрын
awesome cabinets! do you just screw into the studs through the 1/4 ply and nailer strips (for the traditional) and 1/2 ply backer for the basic/shop style?
@amazoneric1
21 күн бұрын
Why aren’t frameless cabinets more common? Not making the face frame seems like a time/cost savings?
@MWAWoodworks
21 күн бұрын
It's more of an aesthetic thing I think. Frameless cabinets usually get put in modern looking kitchens not classic designs
@mattbowers5342
3 жыл бұрын
Glad to have your input on the castle machine. This is an investment I’ve been considering myself
@MWAWoodworks
3 жыл бұрын
It's a really interesting and unique tool. Super clean pockets and easy to assemble with them. And it can speed up your process if you make lots of repeated pockets
@manulepereira6563
2 жыл бұрын
Excellent woodwork ,Thanks for sharing . Happy Holidays Best wishes from India , Mumbai
@progression_decibel
9 ай бұрын
Superb video! So helpful. To each their own with choice of wood but what do you recommend for building cabinets like you show in the video? Baltic Birch, Maple, etc.? I want to build identical cabinets for my laundry room that will last for years and years. Also, at what point in the build process should one prime and paint (or stain) the cabinets to make it easy on one's self? Does it matter?
@seafeye
10 ай бұрын
Do you have a slight overhang on the left and right sides? Are there any pros and cons to making the carcass the same width as the face frame?
@MWAWoodworks
10 ай бұрын
When you install cabinets there are small gaps between each. This gap is taken up by the face frame overhang
@stephenshay7647
2 жыл бұрын
Question regarding the hinges. You don’t have a link to hinges, or for that matter drawer slides on your base cabinets. Any reason? Also what overlay hinge did you use, Blum makes over a dozen. Thank you. Enjoy the channel.
@thefaceexchange
2 жыл бұрын
I want to build cabinets that will fill a wall approximately 12' wide so I'm thinking of making 3 - 4ft wide x 8ft high. Any thoughts on how to best approach this. It does not need to be fancy. Thanks, Joe
@dilinakapugamage
2 жыл бұрын
Excellent job.... What a nicely finished wood work.... Can you plz tell me about the glue that you used here??
@homerscustoms7635
2 жыл бұрын
Do you have plans we can get on the wall and base cabinets
@MWAWoodworks
2 жыл бұрын
Yes! Check the links in the description
@darthr01g41
3 жыл бұрын
Great vid, except for that annoying background "music".
@richardsandfer6214
Жыл бұрын
Really like the practical tips. Question - at 7:29 of this video it shows a cross cut slide that looks and uses materials completely different from your plans. I purchased the Whole Enchilada and was disappointed that it did not include the aluminum extrusion. Please advise. Thank you.
@wescimmarrusti5437
Жыл бұрын
Thanks for pairing your mastery of carpentry with such high level production value. Makes a massive impact when you're able to both show and describe the details so well! Major noob question for you - what do you typically ballpark the cost of a cabinet to be in your head when you're estimating the cost of the wood & hardware?
@tylerbug2009
8 ай бұрын
Excellent video!!! When the weather warms up here in Central NY i need to make some wall cabinets for our pantry/laundry room. I will be making flat panel doors like you did for the new cabinets as well as new doors for the existing cabinets in the pantry and kitchen. Ive been watching how to videos on cabinet building and yours is definitely one of the best.
@makermark67
3 жыл бұрын
Great build. Pretty good timing as well. I've gotta decide on cabinets for the shop and these look great. Thanks.
@MWAWoodworks
3 жыл бұрын
Simple, clean and can also look good in your home 👍
@capemaster123
3 жыл бұрын
Really good timing. I literally have pre finished maple ply for the laundry room. Haha.
@MWAWoodworks
3 жыл бұрын
I love that stuff. So nice and convenient
@paulsofronia2389
3 жыл бұрын
Ha ha same here
@Alan-JackofAllTrades
Жыл бұрын
I like how you use 1/2 panel with rabid for much sturdier door as opposed to using 1/4 panel.
@mrmonkeey1
Жыл бұрын
ye who DIY has all these fancy tools .
@JoseFlores-se3jp
11 ай бұрын
What you guys do for kitchen cabinets shelf’s what banding?
@vanderlei9728
Жыл бұрын
Matt, vou fazer como muitos... não tem como não ser. O trabalho é maravilhoso. Sou brasileiro, não sei se é bom ou ruim. Temos um material parecido aqui chamado compensado marinho, qual material você usou porque tem um tratamento selador e o que temos aqui não brilha como o seu. Além da minha assinatura, tem o meu...
@cbharis
2 жыл бұрын
If you're building a 36 inch wide wall cabinet or wider, and are adding adjustable shelving.. Do you do anything different to the shelves or add more support? Add another shelf pin to the center style?
@kay_to_the_J
2 жыл бұрын
I learned so much in this video! Thank you!
@kay_to_the_J
2 жыл бұрын
Also, it’d be great if you could explain a bit more on where you find your materials. I am still buying from big box stores and it really is subpar
@snuwwulfie6156
11 ай бұрын
cool video but uhm, I don't have the space nor the money for such extreme tools 😭
@MWAWoodworks
11 ай бұрын
😭😭😭😭
@davidburns4176
Жыл бұрын
Why do you use 1/2" plywood for the door panels instead of 1/4"?
@MWAWoodworks
Жыл бұрын
These are shop cabinets so I wanted to be able to hang stuff from the inside if needed
@timabelskamp11
Жыл бұрын
Great video! maybe i missed it but what type of plywood are you using? is seems to be pre-finished?
@thomasfoster5200
Жыл бұрын
Shop cabinets??? I guess my kitchen is a shop because I'd put em in my house
@MWAWoodworks
Жыл бұрын
That's what they are meant for!
@kennith.
2 жыл бұрын
Wow very nice, just a quick question why does the face frame need to overhang?
@JamesJAdams-ll9yk
Жыл бұрын
I'm not a hater, but dude, have you gotten that thing on your neck looked at?!
@MWAWoodworks
Жыл бұрын
Yes 😃
@davidburns4176
Жыл бұрын
The width measurent for the top and bottom pieces is off on the large side if the back panel is supposed to slide behind them.
@andrewgraves4020
Жыл бұрын
Might be a dumb question, but where do you get the insulation from to set on top of your centipede?
@Franko91352
2 жыл бұрын
You’re an awesome Carpinter"……love your videos
@pierluigicolotto9570
2 жыл бұрын
Make it wooden with the help of the woodglut instructions.
@KellyCortijo
7 ай бұрын
Question: why do you need to fasten the nailers to the back panel with brad nails? I'm new at this, but I just want to see if it is a necessary step. Wouldn't you want to fasten them from the back?
@MWAWoodworks
7 ай бұрын
You can glue them if you wish it use screws. The brad nailer is just what I use it's quick and easy and sufficient
@KellyCortijo
7 ай бұрын
Thanks. Would it make a difference if I used the nailer from the back so it doesn't show in the cabinet?@@MWAWoodworks
@MWAWoodworks
7 ай бұрын
Nah I wouldn't work from the back side because the back panel is only 1/4". You won't ever see the brad nails though without a flashlight 🔦 👀
@lolohonu7405
2 жыл бұрын
Awesome explanation, My favorite Wall cabinet video.
@photonashville
3 жыл бұрын
Isn't a Kreg angle 7 degrees and Castle 6 degrees? Who has 15 degree pocket holes?
@MWAWoodworks
3 жыл бұрын
Kreg is 15 degree
@mwinner101
3 жыл бұрын
Kreg works great. Paying $1500 for a pocket jig machine is ridiculous.
@MWAWoodworks
3 жыл бұрын
It's expensive for sure. They make a cheaper version but compared to the price of a kreg system I'm not sure you'd care. But these machines are fantastic for bulk cabinet production!
@engdarfatgalalyelectrical1076
3 жыл бұрын
Your information is beautiful and helpful I hope to be health and safety
@lciummo1
10 ай бұрын
What kind of jig do you use to drill the holes for the shelf hangers?
@victordavidup
Жыл бұрын
Hey man! What kind of table saw you have?
@MWAWoodworks
Жыл бұрын
Sawstop PCS 3hp
@johnisley4578
2 жыл бұрын
Great work.
@VictorCorrea-g8k
Жыл бұрын
Do you build custom sizes for people that you could ship out?
@flfbsphatboyblue8970
Жыл бұрын
Are the plans for the wall cabinets a downloadable plan?
@MWAWoodworks
Жыл бұрын
Yes all plans are downloaded
@ranvirmatharu
2 жыл бұрын
Great Video Matt , you also offer wood work Training
@leandersmith6184
3 жыл бұрын
Would be nice adding some cleats on the back for hanging.
@MountainPostWoodworks
3 жыл бұрын
What size plywood did you use underneath to set the length when you installed the cabinets doors and what where the lengths of the cuts for dado for the sides and back for the first set of cabinets
@DonnieKluck
Жыл бұрын
For the door hinges, I would need to just get full overlay face frame hinges? I bought the project plans but it did not mention what type of hinges were used (that is unless I am blind and missed it).
@MWAWoodworks
Жыл бұрын
I used 3/4 overlay Blum hinges
@mikeennis8820
2 жыл бұрын
Nice work. Why not use 1/4" for the door inserts? Would they be too flimsy or maybe 1/4" isn't available in a nice finish? I was thinking 1/4" would save a few bucks?
@MWAWoodworks
2 жыл бұрын
You can do that for sure. But for shop cabinets I want to be able to hang things on the inside of the door 👍
@theofarmmanager267
2 жыл бұрын
A question if I may. For large panels, I follow your method of rough cutting on the track saw and then finish on the table saw, but, for the sizes you are using here, I trust the track saw to cut the final sizes accurately. Am I missing something here? Supplementary question. Once you have cut your panels to length, your video shows you cutting to width using a factory edge as if that must be 90 degrees to your length cuts. I don’t trust that edge to be square. Again, am I missing something here? Both genuine questions from someone who wants to learn.
@MWAWoodworks
2 жыл бұрын
I don't make finish cuts with my tracksaw unless I'm using my MFT table. It's that or the table saw for speed of setup. I always trim off the factory edge at the table saw. Again, just faster for me at the table saw.
@nehalgohel842
3 жыл бұрын
Hey can you also make a video on how to hang heavy wall cabinets to a concrete wall?
@manuelnunes8415
Жыл бұрын
How do you hang them. I'm always worried they will be too heavy. But I'm super new to this so looking for your advice.
@MWAWoodworks
Жыл бұрын
I have a video on that. Well, on concrete but stud walls are even easier
@MrBubbajohnson1
2 жыл бұрын
Great job Matt,any issues with the fast cap double sided trimmer? It always seems to dig into the plywood on me? Tnx for instruction.
@logmanqasimov5143
Жыл бұрын
Thank you for tutoring us. I was wondering can we make without those big tools? Just with wooden(panel) and drill.
Пікірлер: 297