Since the key was gone this was the only option left, i tried it and though it took some time and broke some of my drills i finally got it, and now the new one works like a charm!! so thanks!
@TinkerBod
2 жыл бұрын
Thanks for the feedback 👍
@MrBackflip500
7 ай бұрын
My bike has fallen over while the steering was locked and the lock is broken inside. I can turn the key as usual but it stayes unlocked. I bought a replacement lock but I could not figure out how to remove bolt. Thank very much Sir!! Thank you.
@TinkerBod
7 ай бұрын
Thanks for the positive comment 👍
@nim205
2 жыл бұрын
I like the way you describe the 3D trajectories, systematic and clean workmanship and fantastic dexterity. Very well done!
@TinkerBod
2 жыл бұрын
Flippin heck thats a nice comment, thanks 👍
@jorgecoelho9303
3 жыл бұрын
The most helpful video I've saw about the removing a fork lock.Congrats.
@TinkerBod
3 жыл бұрын
Thank you...
@paulcooper5610
2 жыл бұрын
Many thanks for this video, I just changed the lock on my cx500, I found it easier to drill a small hole in the rivet and then screw in a self tapping screw. It was then easy to pull on the screw to remove the rivet. Thanks again for posting this video.
@TinkerBod
2 жыл бұрын
No problem, glad it helped, cheers 👍
@theestate12
Жыл бұрын
Wonderful. No way to get a broken key out of the 2016 KTM 500 exc. Followed the video with success. Used a small Dremel and ordinary pliers are sufficient to remove the rivet. Could not have done it without the video. Ride on. Salt Lake City Utah
@TinkerBod
Жыл бұрын
Glad it helped 👍
@npapadakis917
3 жыл бұрын
Very useful video. Thanks to this, I managed to change the steering lock in a EU model XR650R. It is exactly the same with this KTM. One info. While you drill the final stage (large drill), do not have the steering to the lock position (right end). Try to have it a little more centered because, there is a possibility, the old drilled lock to go to the lock position if the steering is at the right end. Any way, if so, then drill with a little larger drill once again (let say if your last drill was 4mm, then put one 5mm and drill again at the same hole). Even if you are in lock or unlock position, the goal is the same. To break the little chrome pin that is 2cm in the lock. And lock or unlocked. this pin is at the same position. Just as the man says. One more thing for the Honda. You do not have to cut the pin that hold the lock to the frame with the wheel and theb catch it and screw it out. On Honda this pin does not have screw threads like the KTM. They are straight along its body. So put, nice and easy, a thin flat screwdriver between the rod and the frame and hit it. The screwdriver will be vertical to the pin. The rod then will pull out the pin. After the first thin flat screwdriver, you can use a little larger one until you make such space between the rod and the frame and then catch the rod with pliers and pull it straight out with the pin on it. It is far more easy this way. Thank you my friend for your video.
@TinkerBod
3 жыл бұрын
Thanks for the kind words and your addition glad it helped 👍
@savyourselffreedom2149
3 жыл бұрын
Thanks so much I've had new lock kit from honda for 3mths now I have the knowledge to do my xr650r .cheers mate from Australia
@TinkerBod
3 жыл бұрын
Cheers for the positive comments, much appreciated, good to hear stuff like this..
@johnbaker1816
3 жыл бұрын
Excellent explanation...calm, reasoned and informative. Thank you very much. Off to the shed now to install new lock on my 500EXC!
@TinkerBod
3 жыл бұрын
Thank you for the kind words & good luck
@kenpolukeTheREAL
2 жыл бұрын
This helped me tremendously. I was finally able to replace the lock on my savage.
@TinkerBod
2 жыл бұрын
Super 👌
@MrVM41
9 ай бұрын
Spot on for what I had to do to a old Honda, only thing is the rivit is bigger on the Honda and the one they gave was tiny.
@Chuckstergun
3 жыл бұрын
Thanks! Had to get a new ignition switch or my Husky 501S. Also got the steering lock to match the new keys. Your video was a huge help!
@TinkerBod
3 жыл бұрын
Great to hear, Cheers!
@MisterGank
3 жыл бұрын
Great info. Thanks for the video. However, you just greased that lock... Do NOT use graphite after using GREASE!!! Mixing the two is almost like glue. If you started with grease, you'll want to use an oil or dry lube.
@TinkerBod
3 жыл бұрын
Great point!
@jimfield3023
2 ай бұрын
Glad I saw this on here broken mine to day thanks
@moosey62
3 жыл бұрын
Can confirm this works Triumph Bonny 2011, locked and bashed in by thieves. We drilled it out 2mm, 4mm 6mm. Fell right out. The rivet pin just neded a bit of filing. That lock is just brass. Drill at 01.00. Sorted in 10 minutes.
@mattbillenstein
2 жыл бұрын
Note, if you don't have a dremel, a small triangular file works on the rivet thing - just file a couple flats on each side and grab it with a vise grip...
@domste
3 жыл бұрын
Thank you very much! I ended up removing the rivet with a bottle opener (some kits seem to come without it so I saved it) and used a lockpick to turn and remove the cylinder. Nevertheless I couldn’t have thought about doing these things if I hadn’t seen you explaining how the lock works and how it can’t be opened. Thanks 🙏🏻
@TinkerBod
3 жыл бұрын
Nice work! thanks for the comment.
@rc2634
Жыл бұрын
@Domenico Stefani Your idea sounds great, but I am not sure how you used the bottle opener? Did you had to drill the rivet first? Or how did it go? Thanks!
@markp5737
3 жыл бұрын
Outstanding video, thanks so much, off to change my steering lock :)
@TinkerBod
3 жыл бұрын
WOW, praise indeed, thanks...
@brianrundle9219
2 жыл бұрын
Very skilled and steady. Very impressed.
@TinkerBod
2 жыл бұрын
Thanks...
@smeggysmeg2837
3 жыл бұрын
informative video, thanks. would have had no idea where to begin without this video. only issue is the head broke off the rivet when i tried twisting/pulling it out with the visegrips. then had to drill out the rest of the rivet from the hole. not easy to get that little bastard rivet pin out!
@TinkerBod
3 жыл бұрын
You done well getting that out they are quite hard, that would have right pee'd me off.
@timothysims
3 жыл бұрын
Perfect video, straight to the point. Thank you.
@TinkerBod
3 жыл бұрын
Cheers 👍
@birchgerke140
17 күн бұрын
Thanks, I wad going to drill the center with a bigger drill. This works much better.
@TinkerBod
16 күн бұрын
Excellent!
@colinculverwell325
5 ай бұрын
My bike didn't have a key for the steering lock. I rode it to a local locksmiths who picked the lock and extracted it in about two minutes. Charged me £6. There was a number on the back of the lock so I was able to order a key and reuse it.
@dagre1839
2 жыл бұрын
Thanks I got a brand new bajaj re which nobody even the dealer could ever lock. Least I know a little about the solution now
@TinkerBod
2 жыл бұрын
👍
@fernandodavidpoma7891
Жыл бұрын
thanks man!! totally useful video for my Kawasaki KLX300R 99
@TinkerBod
Жыл бұрын
You're welcome!
@SNTMoto
3 жыл бұрын
Thank you so much for this amazing tutorial
@TinkerBod
3 жыл бұрын
Thank you, much appericated.
@trevorbest5715
2 жыл бұрын
Very informative video. I watched this as my daughters cg125 has steering permanently locked. A new key she got turns the barrel and it pops out as per normal but the steering lock stays on. How is this possible? Ive sprayed with switch cleaner and the lock / barrel move freely both rotationaly and in and out so I am puzzled as to how the steering lock is staying on. Thanks
@TinkerBod
2 жыл бұрын
You might find the rear has sheared off, unlock it, tip the bike right over so lock is towards the ground and wiggle the handle bars. Had to do it with an old yam dt once.
@officialmysteriousrider6327
4 жыл бұрын
Should of made a little tear drop cover before putting rivet back in itll protect your steering lock. I don't no why the factory didn't fit one on your bike but I do no my dt125r has the little cover on it & its same kind of lock has yours & the little cover would fit yours too buddy
@TinkerBod
4 жыл бұрын
Put simply its a ktm and if they can leave anything off to save 2pence they do, then charge you twice the price to put it back on and call it a ktm power part. Look after that dt cracking bike that really miss mine.
@eyeflynoosa
Жыл бұрын
so you can withdraw the barrel if you have the key, is that correct? my bike has fallen over while the steering was locked and has jammed it in the locked position, I managed to unjam it but I don't trust the mechanism anymore and want to replace it.
@eyeflynoosa
Жыл бұрын
nevermind, i managed to get it out without dremel or drilling, my 07 ktm 625 lock mechanism was a bit different though, it has a spring down inside the very bottom of the hole for the lock, the actual steel "bolt" that pushes into the steering column and had snapped away , I managed to get it out with needle nose players. thanks for uploading this video , I would have been fkd without it, cheers
@TinkerBod
Жыл бұрын
Cheers, I'm glad it helped 👍
@aatesser
2 жыл бұрын
Thanks tinkerbod, great vid Good Buddy! Many thanks for sure. Al
@TinkerBod
2 жыл бұрын
Cheers 👍
@forevermusic2766
4 жыл бұрын
Some guys tried to steel My bike and broke up the steering lock... But They didnt get away😳 Thanks for helping! 🙂Now i got a new lock and one extra lock for the wheel! F**k thiefs!
@officialmysteriousrider6327
4 жыл бұрын
Sillen Driveway alarm on ebay put the sensor in your garage And the receiver in your bedroom when it goes off youll hear it & their wont then you go out & kick the shit out of them good luck
@Ray-cv6gc
4 жыл бұрын
Weak,useless,forgot to unlock mine and rode off ,broke very easily!😠
@moovintruespace994
3 жыл бұрын
But people who steal are not in their right mind..Great tutorial though. Thank you
@mitchoh7603
Жыл бұрын
Just replaced My ktm530excr lock, all went to plan I was chuffed with myself until I realised it doesn't lock at all now it just clicks unlocked when you move the handle bars... lock or frame issue? Any help or input would be great!
@TinkerBod
Жыл бұрын
If you have used the genuine lock check the frame to make sure the track/keyway it runs in is clear 👍
@juliussalovaara9787
Жыл бұрын
Did you find the problem?
@danhopkinson2811
3 жыл бұрын
yeh thieves just twist the bars hard and snap the fragile little steering lock
@jacob-no4tf
2 жыл бұрын
Thank you for sharing.
@ShannonHartnett-117
Жыл бұрын
So I failed to get the rivet out of mine with the vice grips it snapped off short so i probably end up just drilling it out such a shitty thing to happen no key from previous owner so had it put into a mechanic after ordering a new key and barrel kit from suzuki and the mechanic made a mess of the key hole now I guess I'll have to try this procedure now apart from the drilling or should I use a screw extractor instead of the drill bit?
@coolguy9651
2 жыл бұрын
Thanks man, i appreciate it.
@TinkerBod
2 жыл бұрын
Glad I could help
@kopftuchgejo2541
8 ай бұрын
Super Danke 👍
@moosey62
3 жыл бұрын
Thanks so much!
@TinkerBod
3 жыл бұрын
You're welcome!
@davexboot
Жыл бұрын
thank you got it out no problems Kauai KTM Hawaii
@TinkerBod
Жыл бұрын
Super 👌
@krishampton7060
2 жыл бұрын
Is there a way of getting a key made for this type of lock as I have a 93 Kawasaki klx 250 and the lock is unlocked in the frame but I have no key to remove it from the frame and I don’t want to destroy it if I can help it, cheers 👍🏻
@TinkerBod
2 жыл бұрын
Sorry no idea, maybe someone can help you in the comments, best of luck. 😁
@racer8115
7 ай бұрын
So I did this and the rivet snapped off and is stuck. Anything I can do?
@zeishoot
Жыл бұрын
I just broke the fucin rivet… how do i do now 😢
@TinkerBod
Жыл бұрын
Drill it out with a left hand drill bit, but make sure its a soft pin first.
@TheVinsontafoya
4 жыл бұрын
I have a husqvarna that I need to do this on. Is that part number across the board? I have a 2008.
@TinkerBod
4 жыл бұрын
Hi, Not sure sorry.
@danielmcpherson298
3 жыл бұрын
can you link where you got the steering lock from?
@TinkerBod
3 жыл бұрын
Fowlers of Bristol Uk parts department online.
@aaronsanchezz
4 жыл бұрын
Will this work if the bike is locked? My bike been sitting for a month in my driveway since i lost the key... got a lock pick gun and it didn't work :( and i couldn't pick it
@TinkerBod
4 жыл бұрын
It will but remember the pin will not be in the same place because it is in the rotated locked position so you will need to allow for this.
@17teknik_servis
4 жыл бұрын
thanks for this vid..
@TinkerBod
4 жыл бұрын
Thanks, no problem
@richardheaton7561
3 жыл бұрын
How much would you charge to do mine ??
@TinkerBod
3 жыл бұрын
Sorry, its not something i would be able to do.
@domste
3 жыл бұрын
Hi Richard, try to see if your rivet comes out with a simple bottle opener (I used the thin one from a swiss knife and it worked like a charm). Removing the lock cylinder was a very easy lockpicking job: you will be alright with a lockpicking tutorial on youtube and a couple of tools dremel-ed out from the metal strip found in old windshield wipers. The drill trick might be quicker tho haha
@rc2634
Жыл бұрын
@@domste Your idea sounds great, but I am not sure how you used the bottle opener? Did you had to drill the rivet first? Or how did it go? Thanks!
@elvy3236
4 жыл бұрын
What year is this bike
@TinkerBod
4 жыл бұрын
2017 but they span many years for all makes
@martinoconnor4314
3 жыл бұрын
Does this method still work if the steering lock is in the locked position?
@TinkerBod
3 жыл бұрын
Yes it does but be careful not to damage bike frame as you need to drill in at move of a angle without catching the frame just taking out the locking pin. Not easy.
@martinoconnor4314
3 жыл бұрын
@@TinkerBod Thanks for your reply, I think I was drilling it out while you were typing. I drilled straight into the middle of the lock with a 6mm drill bit as I didn't have anything smaller that wasn't made of chocolate. I could feel the locks internal wafers breaking up with the drill bit, when I had got through all five I just put a large flat blade screwdriver in the remains of the key slot, slightly turned it and the lock popped straight out. The locating pin was still intact but as long as the locks internal wafers are drilled through there is nothing holding the lock closed. TBH I think going for the centre of the lock is even easier than trying to aim for the pin as you don't need to be that accurate and there is no chance of even hitting the frame lug, also you don't have to go as deep as the pin.
@thestylefrreak
2 жыл бұрын
@@martinoconnor4314 do you have any picture of how to drill at the center ?
@officialmysteriousrider6327
4 жыл бұрын
Should of made yourself a little cover out of aluminum before putting rivet on to stop water getting in & seizing your new lock dont no why it doesn't have a cover from the factory in the first place easy anuff to make you have the shape already in front of the lock
@TinkerBod
4 жыл бұрын
I agree, other bikes i have had have always had them. Its just another way ktm can save a penny. I surprised they are not a ktm power part for £50
@officialmysteriousrider6327
4 жыл бұрын
@@TinkerBod that's ktm for you expensive pal just like yamaha but still easy anuff to make one you'll just ofto get yourself a new rivet if you do
Пікірлер: 101