You've missed a trick: If you have internally routed cables and no special tools, leave the old cable housing in place and remove the old cable. Put the new cable through the old housing. Then remove the old housing while holding the new cable in place. Finally, you can use the new cable to guide the new housing through the frame.
@nounours2627
Жыл бұрын
Good trick (I use it often) but only works if you have cables twice the length of the housings. Could be problematic with full housing fully internal system. Explanation: the cable serves as a guide so it has to be from one end to the other of the frame but you also have to fit the entire new housing before inserting it in the frame or you won't be able to hold the cable in place while inserting the housing => You need a cable roughly longer than two time the housing which may not work if you have a fully internal housing system that often require more than 1m50-1m80 (you rarely see 4m+ cables)
@islandaerial3414
Жыл бұрын
Here's a hack: Use a picture hanging nail to 'connect' old and new outer housing. Just cut the head off of the nail. The barbs do a great job of holding the housings together while you push/pull the new housing through the frame
@CyclingLifePT
Жыл бұрын
I liked Doddy's honesty by revealing you don't really need the ParkTools IR-1.2 Internal cable routing kit. What i usually do is use an old inner cable to hold the old and new outer cable together and just push the new outer cable in instead of pulling the old outer cable out. You can even use a bit of scotch tape to keep both the old and new outer cables together, but usually just having the inner cable going through both is enough. About the 'cable stretching': The cable can in fact stretch, if you performed your maintenance on a really cold environment and ride in a hot environment. So, that barrel adjuster comes in handy especially when the temperature varies wildly in the environments where you ride.
@Beiberhole69RVA
Жыл бұрын
Another hack is to use a light suspension grease (I use Slickoleum), and coat the inner shift cable with it very lightly, before inserting it into the housing. Zero friction, and protects it if water gets in the housing. Works better than using chain lube and lasts longer. I used to use Triflow in the outer housing, but the Slickoleum works much better.
@swissride4k
Жыл бұрын
I'm happy to see you are a very honest man and your all reviews about cycles are pretty straightforward and full of truth 😇 Hope to get this cycle very Soon for my cycling tours in Switzerland
@Velo1010
Ай бұрын
Great video with simple explanations.
@puffilp4493
Жыл бұрын
Already missed Doddys Reactor ST. Had to change the brake housing on my Reactor recently. I would have needed this video🥲. Thx for the effort u guys put into your Videos.❤
@michaelbondad3912
Жыл бұрын
Great timing for this video as im build my 2022 chameleon frame today.
@gmbntech
Жыл бұрын
Nice one, Michael! We bet it looks sick! When it's built, feel free to send it to our uploader! 👍
@dbucka
Жыл бұрын
If the ends of the cable housing are outside the frame, how is moisture prevented from getting in? Isn’t this then the same as external cables? Aren’t internal cables ONLY for looks? The PITA factor and tool requirements for internal routing make this system a scourge on our sport! The other bad idea dreamed up by the marketing departments is any press fit BB system. Just my humble opinion… great video as always!
@SteveSUX2BU
Жыл бұрын
When replacing the shifter cable, the shifter should be in the highest gear. Not the lowest.
@dillonfreman2726
Жыл бұрын
You can use a short piece of housing and cable puller (if you have one) to seat the housing ends before you tighten down the pinch bolt. Helps a lot to eliminate the step of "seating" the ferruls before you lock down the pinch bolt and compromise the cable.
@Adam-vm8kp
Жыл бұрын
You should be stretching the cables anyway which will make sure the ferrules are fully seated, I just push the ferrules on with my hand and then push it against the workbench. No need to complicate things.
@alanfrye2706
Жыл бұрын
Been a long time since a saw thumb shifter.
@1972mdc
Жыл бұрын
Tie a string to the cable and drop it into the frame. Hold vacuum cleaner nozzle to outlet and the string is sucked through, then pull cable through… no expensive tool needed
@adamcairns8732
Жыл бұрын
How do you tie a string to a cable?
@1972mdc
Жыл бұрын
@@adamcairns8732 maybe you can glean from this but I did it and worked great - kzitem.info/news/bejne/z3duuYSihZOGmnY
@galenkehler
Жыл бұрын
@@adamcairns8732 tape it on
@kahnny23
4 ай бұрын
Can you replace the inner cable only? I don't want to replace the housing from inside the frame
@chris4536
4 ай бұрын
You sure can! Nice and simple 👌
@stuartwoodburn2653
Жыл бұрын
I resonantly did this on a friends Trek super caliper it has internal cable but not for the outer housing only the inner cable with stoppers in the frame. I pulled the inner cable out before I realized, it was a nightmare to put a new cable though. I managed to tread a old inner cable frame the bottom and with some help fishing it out. After treading the inner cable though the shifter I gaffa taped it to the old cable and pulled it though. Ifyou have this bike check before starting I hope it helps someone.
@MrMonty414
Жыл бұрын
Thank you. Very helpful. 👍
@monetaryjack1705
Жыл бұрын
Good success cutting outers with a metal blade(very thin) on an angle grinder. All cable cutters leave a sh*tty ragged end- on Velotech Gold was advised to file the end flat if possible. Internal routing is a pain in the a*se really...My KTM is due for some TLC soon and most likely this will involve dropping the motor from it...Oh and just beware the screw on port entry things on frames, some are so badly designed they have a threaded plate which falls off the screw/bolt and into the frame!!
@arronspuddylaird5357
Жыл бұрын
If only I knew about indexing in my last ride 😂 it would have lasted longer thanks doddy
@asiluawksadvnase8238
Жыл бұрын
Pull the old cable, thread a new cable through the old housing, it needs to be 2x as long as the housing which they usually are. Then pull the old housing. Thread the new housing onto the new cable and push it through, it follows the cable. Takes seconds and uses no gear at all.
@bladesandbows1521
5 ай бұрын
How do I know the length of my cable if I don’t have anything to reference?
@roygumpel8415
2 ай бұрын
how the heck does one replace ebike wiring, from the display to the motor?? unlike this cable, they have connectors and other fat things at the end!! insane.
@craigmoran5238
Жыл бұрын
Or just tape the new cable to the old one before you pull it out.
@adamcairns8732
Жыл бұрын
Tape cables together and pull? Have you actually successfully done that?
@gmbntech
Жыл бұрын
That sometimes works; however, they're more than likely to come apart whilst you pull the cable through. It's better to use a dedicated cable routing kit. 👍
@Danil-Crypto
Жыл бұрын
it is better to lubricate through a needle because dust and dirt will stick to the edge of the shirt
@Tenneszoomers
2 ай бұрын
This man honestly sounds like gordan Ramsay to me
@Rob_Champ
Жыл бұрын
🤘
@ivanperica3731
Жыл бұрын
This video is outdated, nowdays cales are routed through headset. I am confused.
@michaelmechex
Жыл бұрын
Not on most mountain bikes. And in my opinion they shouldn't be. If you need a tutorial for that check a road bike specific one.
@michaelbondad3912
Жыл бұрын
Road bikes or super bikes have this. Not most mtb
@mojo3398
Жыл бұрын
@@michaelbondad3912 most new bikes by big manufacturers. even commencal did it with the tempo. COMMENCAL!!! :(
@tomassanesson902
Жыл бұрын
Good to no 🤘
@Steven-qm1xo
Жыл бұрын
You don't root the cable you route it... Rooting cable sounds silly ...lol, 😀
@Mavrik-60
Жыл бұрын
By goly gee I'll root it if i dam well wat to MATE
@michaelbondad3912
Жыл бұрын
Different ways to say things man. Ever heard someone from cali talk vs texas or Louisiana? You know where english came from right? England.
@Mavrik-60
Жыл бұрын
@@michaelbondad3912 i know just giving him a hard time. Some people got nothing better to do than set there and pick on every mistake they come across, you know like there perfect usually there the worst because there always pointing there finger at someone else,
@monetaryjack1705
Жыл бұрын
@@Mavrik-60 Yankees eh? they should take a good look at themselves in the meeeeeror (That's "Mirror" pronounced in American lol)
@gmbntech
Жыл бұрын
Facts! 😂 Thanks Steven!
@bobothericefarmer1878
Жыл бұрын
Sheeesh
@wojciechopyrcha9116
Жыл бұрын
For me internal routing is one of most idiotic and annoying things in bikes. F... it
@gmbntech
Жыл бұрын
Internal routing makes a bike look much cleaner, but it can be a bit fiddly to set up. 😅
@wojciechopyrcha9116
Жыл бұрын
@@gmbntech by the way. Clean look can be good for roadies. But true moutain bike have to be easy to service in any place in winter when I ride in gloves in -15 degrees. So why I love my cheap enduro bike. It is almost as good when I ride but it is easy to work with it. And costs 8k. Not 19k. With the same components. Almost only difference is frame.
@prithviraj2354
Жыл бұрын
First like and comment😇
@phenofinder9145
Жыл бұрын
Uhm...... okay.... Cool
@gmbntech
Жыл бұрын
🥇🤘
@Adam-vm8kp
Жыл бұрын
Wow what did the papers say?
@prithviraj2354
Жыл бұрын
@@Adam-vm8kp read the papers again to know more.....
Пікірлер: 56