I watch this video every year when I need to replace the bulb. Thanks for putting this video up!! Wish I could give it a like every time I watch it
@Dc5Aspecd
3 жыл бұрын
Thanks for the feedback josh!
@bjeike
5 жыл бұрын
We've had this system for three years now, I always watch this video before I change the UV bulb as a refresher course, to make sure I don't forget everything. Nice short, to the point video that hits everything.
@Dc5Aspecd
5 жыл бұрын
Thanks for the feedback! Means a lot.
@marissaawesome2422
2 жыл бұрын
Me too..lol..I even wrote everything down. Handwriting is like a Doctor..lol..So the video is a must..Thank you
@JulieAppA
3 жыл бұрын
This year it was up to me to change bulb and the sleeve 😄 and I nailed it . Thank you for the video
@Dc5Aspecd
3 жыл бұрын
Good job! Thanks for the feedback 👍
@CHav-uc3or
5 жыл бұрын
Perfect video. Never done it before. Took me less time to do it than it did to watch the video
@Dc5Aspecd
5 жыл бұрын
Cameron Havlin happy to hear that Cameron! Thanks for the feedback!
@dantratnack8217
3 жыл бұрын
Thank you! This is the most helpful DIY video I've watched since moving into my new house a year ago. Very clear and understandable.
@timernst8909
2 жыл бұрын
Great job. You showed details others have not. Thx!!
@billygarner7539
2 жыл бұрын
GREAT video.. Just changed mine for 1st time and followed along with you. Simple! Thanks!
@samuelgorla6417
5 ай бұрын
Thank you, Justin!
@pweiss1983
2 жыл бұрын
You saved me hundreds of dollars and the stress of dealing with our assh*le plumber with this video. I am forever in your debt.
@Rostlk
Жыл бұрын
Hi. Excellent video. I changed my bulb based on your video before. This time the GDS unit shows 2.6 after power is plugged in, then cycles and shows zero and red LED. It also doesn't reset after holding the reset button
@Dc5Aspecd
Жыл бұрын
Sounds like the ballast inside the control box is bad. If you have the newer style with the black plastic box the part number is ATS1-421P-GDS. if stainless it’s ATS1-421-GDS.
@DBRobins
3 жыл бұрын
Thanks for the video - I’m down to 14 days. Any particular website I can order the bulb?
@taylorsheehy4053
4 ай бұрын
How bright should the UV light be through the viewing/peep hole on the side? We recently replaced our bulb and I recall it being much brighter previously.
@jackie5046
2 ай бұрын
Why would 2 channel locks be needed for loosening the nut? Mine wont budge but why 2 CL instead of just one?
@wrenglish
3 жыл бұрын
Hi Justin everything went great with the reset, except my watts were reading 57-60. Is that an acceptable range?
@dixiedownunder1
Жыл бұрын
I just ignored the whole part about the quartz sleeve after I had some trouble with pressure. How much of a risk is it to just replace the bulb and not the quartz sleeve?
@trinityhousebuying8887
2 жыл бұрын
Hey Justin, The previous owner/installer installed our system without the necessary clearance to remove the lamp/quartz. ( duct work in the way) Can it be replaced at the bottom with a similar technique? Only have 2 days left, please advise as soon as possible. Thank you very much! Chuck
@shazzorama
3 жыл бұрын
Ours is older, ATS EV SERIES EV-8E, 12 E. Ballast stopped working and our lamps last maybe 6 months.
@gwenaveremarket8469
2 жыл бұрын
i know this video is old but i installed my new bulb and the machine won’t reset - it just says LO with red flashing and won’t do anything when i hold the button down
@nicholaswitt9603
4 жыл бұрын
How did u know where to put the compressing ring
@JerseyCapper
Жыл бұрын
Why is my alarm on the system still beeping? I replaced the bulb and held the reset button but nothing happens as far as the beeping starting. Thanks for your help!
@billgeorge9020
Жыл бұрын
Mine is still beeping too. How did you resolve this?
@JerseyCapper
Жыл бұрын
@@billgeorge9020 unfortunately called a water company to come out and replace when I was on a business trip. Was resolved when they did.
@billgeorge9020
Жыл бұрын
@@JerseyCapper did they have to replace the whole unit?
@JerseyCapper
Жыл бұрын
@@billgeorge9020 nope, just the lamp which I already purchased. I’m assuming they have some kind of method to stopping the beeping aside from what we’re told as consumers (told to hold the rest button or whatever)
@TheLeewenger90
5 жыл бұрын
Great video but I have a bit of a problem.. the quartz sleeve shattered in mine. How do I get it out? I'm guessing I just need to flush the broken glass out the bottom somehow?
@Dc5Aspecd
5 жыл бұрын
Unfortunately, you’ll have to cut the plumbing, to remove any broken glass that is in the chamber. Thanks for the feedback!
@heather9074
Жыл бұрын
Does the glass HAVE to be removed?
@wrenglish
3 жыл бұрын
I just unplugged and restarted it now says 30...
@reeldealva37
5 жыл бұрын
Where do you buy the bulb at?
@CHav-uc3or
5 жыл бұрын
Amazon best place just punch in model number
@Dc5Aspecd
5 жыл бұрын
You can call me at 717-697-4998 and I can look up a dealer in your area. I would stay away from lamps on amazon or others from China, as they don’t burn at the same intensity and can cause damage to your system. Our systems are made in the USA and have a minimum of 30,000 dose at end of life.
@hautemama24
4 жыл бұрын
@@Dc5Aspecd where do you find the model number at? We purchased a home and are still trying to figure all of this stuff out :)
@Dc5Aspecd
4 жыл бұрын
@@hautemama24 If the system looks similar to the one in the video, the model/serial number will be located towards the bottom of the stainless steel housing/ cylinder. If there is a cover over the whole system, it's located underneath the cover and on the top plate where the electronics is located. You can always email me too at Justin@aquat.com to send me a picture of the system.
@TheDonzim
4 жыл бұрын
@@Dc5Aspecd ,can I call you with a few questions? Of course at your convenience,thank you,Don
@jsdreyer2031
8 ай бұрын
Don't handle either your bulb or your quartz sleeve with bare hands. :)
@wrenglish
3 жыл бұрын
Hi Justin everything went great with the reset, except my watts were reading 57-60. Is that an acceptable range?
Пікірлер: 44