Very clever use of tape to control the oil draining from the forward drain plug!
@kdsowen2882
4 жыл бұрын
A bit over-torqued on the 12mm plug, missed the lower o-ring on the lower filter-cover-bolt, and didnt bleed the filter of air, using the bleed-screw located on top of the filter housing, but otherwise, very soothing viewing, as someone else mentioned.
@edwinlim4596
3 жыл бұрын
How do you bleed oil filter of air?
@hodaka1000
2 жыл бұрын
@@edwinlim4596 Very carefully It's the screw at the top centre of the oil filter cover use an 8mm spanner to loosen it and then start the motor and using your fingers unscrew it very slowly and carefully until oil comes out You do this when you first fire it up after an oil change It's tricky because it is very easy to loosen it to much and the screw can come out and you'll get oil all over your ceiling Keep some rags on hand for any spillage and maybe slip a pan under it to catch any oil and keep a good grip on the screw with your fingers and be ready to hit the kill switch or ignition switch as I said it's tricky but you want to try to turn the screw out until it is held in by one thread Once oil flows past the screw tighten it back up and clean up the mess 😃👍
@hodaka1000
2 жыл бұрын
@@edwinlim4596 There is also a mesh filter in the bottom of the frame oil tank below the drain plug where the oil hose attaches and there is a mesh filter in the sump plate under the motor this screen in the sump plate is where you will find any broken pieces or metal shavings Metal shavings are most likely aluminium from the timing chain guide and will lessen and eventually disappear with use, if you see shavings chances are after a couple of oil changes you will no longer see them Get a manual
@edwinlim4596
2 жыл бұрын
@@hodaka1000 thanks a lot!
@hodaka1000
2 жыл бұрын
@@edwinlim4596 😃👍 🇦🇺
@normanplombe2889
5 жыл бұрын
Dude's done this before. Now I'll do my first one like I've done it before too!
@Dranreb865
6 жыл бұрын
This is the reason why i like this bike better than a scrambler 62. No non-sense dealer bullshiets with its service reminder reset crap!
@ClearBrookExotics
6 жыл бұрын
Nice job. I need to add an SR400 to my garage!
@Svendus
5 ай бұрын
Well Done but did you ever clean the filter or the strainer sitting in the bottom of the frame ❓a tips you can fill the filter house with an oilcan after filter change, then the engine will get oil immediately after restart and you don’t have to bleed the filter house for Air 👍
@chazwazzum
4 жыл бұрын
excellent video. Very clear and efficient. 😎👍 (also, very soothing to watch. 🔧 adding this to my saved videos)
@PONSR500
Ай бұрын
どうもありがとうございます! Muchas gracias!
@white_9991
Жыл бұрын
Very useful video 👍, thanks!
@Polecat54941
5 жыл бұрын
Excellently made video,very helpful
@LeonePieraccioni
3 жыл бұрын
Great video! Detailed but simple. Where do you buy the washers? Thanks!
I noticed aluminum oxidation on the engine cover. I have the same on mine, only on that engine cover. Have you used something to take it off?
@DJMadMaarten
5 жыл бұрын
Have the same issue. You found a solution for that?
@honestjohn6222
4 жыл бұрын
Great video , Thanks
@Kulak-sw3qo
4 жыл бұрын
Thanks from Ukraine
@user-yr8wy4yu3b
8 жыл бұрын
久しぶりのSRのオイル交換動画ですね(≧∇≦)
@hodaka1000
4 жыл бұрын
Should do it right. There is a mesh filter in the bottom of front down tube oil tank and a mesh screen in the sump plate below the engine this is where you will find any broken pieces and shavings. There is also a bleeder screw in the top of the oil filter cover to release air from the filter. Glad I'm not paying him.
@kdsowen2882
4 жыл бұрын
And, what he said...
@apple12rpo19
4 ай бұрын
Круто
@jasongray7198
2 жыл бұрын
Thank you so much
@Indy125
7 жыл бұрын
My US spec sr400 has 10mm drain plug on the frame.
Пікірлер: 62