I really have to thank autodoc for making these videos.
@autodocuk
2 жыл бұрын
Thanks for your positive comment! Stay with us!
@masoncooper6649
3 жыл бұрын
mechanics like this is the exact reason Id rather work on my own car
@autodocuk
3 жыл бұрын
Thank you for sharing your opinion!
@laliux32
2 жыл бұрын
I may be wrong, but as far as I remember, a bearing should never be lubricated to proceed with its assembly, the surface that receives it must be dry and grease-free
@ntsakisikhubayi3989
3 ай бұрын
Looks simple enough! But is the press tool not better?
@autodocuk
3 ай бұрын
This video is for informational purposes only and does not guarantee a specific result. In this case, the part was not tightly clamped. You should choose methods depending on the complexity of a particular repair.
@sudinebabz8651
4 жыл бұрын
Très bien 👍🏽
@derf9465
2 жыл бұрын
Thankyou. My sandero will be sorted shortly
@autodocuk
2 жыл бұрын
Thanks for your positive comment! Stay with us!
@curtisgee7303
3 жыл бұрын
This quickly became a WD40 ad
@aboelrouk
2 жыл бұрын
Very pro !! unbelievable !
@autodocuk
2 жыл бұрын
We're glad you found this video useful!
@MrGillystar
3 жыл бұрын
I need to replace the ABS ring as broke apart for rusting. Will i need to replace wheel bearing to get to the ABS ring? Thank You...
@autodocuk
3 жыл бұрын
Unfortunately, it is not possible to answer your question, there may be a lot of reasons, we advise you to contact the service for a complete diagnosis and identify the cause of the problem. AUTODOC
@nigelbiscombe9199
Жыл бұрын
What was the torque setting on the wheel bearing? You don't just impact gun then up!! Or you risk damaging the race.
@autodocuk
Жыл бұрын
You can find this information in the technical documentation for the repair of your car or we recommend contacting the service.
@neymarjunior9890
2 жыл бұрын
Post video about How to change front wheel brings for Mercedes 4 matic
@autodocuk
2 жыл бұрын
Unfortunately we don't have the video for this car. AUTODOC
@milannjozicc3986
Жыл бұрын
Do you have your mechanics in Czechia to fix my car?
@autodocuk
Жыл бұрын
Thank you for contacting us. We are an online shop for car parts and we do not repair cars. Feel free to contact us back and we will be happy to assist you.
@1006peter
3 жыл бұрын
so much helpfull
@autodocuk
3 жыл бұрын
Thanks for your positive comment! Stay with us!
@Soapy555
2 жыл бұрын
Never spray lubricant on, or near your brake discs or pads 13:19...... using brake cleaner afterwards is not the answer!
@autodocuk
2 жыл бұрын
Thank you for your comment.
@Jayc1993uk
3 жыл бұрын
Doing this job as we speak thanks for the video as a guide 🙏
@autodocuk
3 жыл бұрын
We are glad that you enjoy our work!
@RupertReynolds1962
3 жыл бұрын
Helpful vid, but he kept pulling the torque wrench harder after it clicked for all the bigger fasteners. Some of them were already over-tightened by the rattle gun before the torque wrench was used. Over-tightened fasteners can be bad, plus kt's a bad habjt, because it can damage some torque wrenches. Also, he fitted the disc withoout cleaning off the oil and grease he put on there while he was working.
@derf9465
2 жыл бұрын
Pads should do that.............
@arjenboerdijk7412
11 ай бұрын
WARNING: the front hub nut needs 280 Nm (source: Haynes manual), and not 162 Nm. This is very dangerous!
@autodocuk
11 ай бұрын
You are absolutely right and the correct tightening torque is 280 Nm.
@JamesSmith-tv3pz
3 жыл бұрын
Generally an excellent guide, however 2 -points that need to be reviewed here. 1). You should not be using standard 'chrome' multi-point sockets with an impact wrench. 2). You fully tighten all fixing bolts/nuts with an impact wrench and then attempt to 'torque-up' the bolts/nuts with a torque wrench. These fixings could already be over-tightened.
@autodocuk
3 жыл бұрын
Thank you for your helpful feedback. We have already taken into account all the mistakes and have tightened all the nodes only with a torque wrench in our new videos. AUTODOC
Пікірлер: 33