Did you notice that our mechanic made a mistake? Let us know in the comments what the mistake was and when you noticed it 💬
@branimirpodboj
3 жыл бұрын
From 7:08 he was spraying bolt head with cooper grease not the threads.
@autodocuk
3 жыл бұрын
Our viewers are so observant! The correct answer: The steering knuckle is not jacked up at 3:00
@chrisfromukyt
2 жыл бұрын
@@autodocuk So how is it supposed to look or be done? How is it to be jacked up, am I going to cause damage by not "jacking it up"? Please explain.
@piotrb6579
8 ай бұрын
Wrong torque for hub bolts, instead of 71nm should be 90nm + 45degrees. Driveshaft nut should be tightened 150nm -45degrees then 250nm
@tomatoknuckles
11 ай бұрын
By far, the best walk throughs on KZitem. No cut corners atall.. This made it easy for me to follow along and do it myself.
@КотикиШахматисты
3 жыл бұрын
Wonderful job! Even the tightening torques in Nm are shown
@autodocuk
3 жыл бұрын
Thank you for sharing your opinion!
@titomiss
3 жыл бұрын
Why you not use firt the air impact for wheel and central bolt ?
@renovateandflip2073
Жыл бұрын
Great job and easy to follow
@mustafamechanic1094
3 жыл бұрын
It's very beautiful
@istvannyiri5687
Жыл бұрын
Is it enough torque the driveshatf nut to 165nm? 7:30 Somewhere i heard the factory manuals are, 150nm then 45degrees and 250nm. So which one is correct?
@autodocuk
Жыл бұрын
The correct moment value is 250 nm.
@igorantonijevic9396
Жыл бұрын
Hello everyone. Can someone tell me what the wire coming out of the bearing is for? I assume that it is some kind of sensor, but for what?
@autodocuk
Жыл бұрын
In this case, it is the wire from the ABS sensor.
@alexey9900
3 жыл бұрын
Good 👍👍👍
@cowpat
Жыл бұрын
Never seen someone use so much copper grease
@TYEGaming
3 жыл бұрын
He didnt torque it to the required spec ( 77nm)
@antoniofascia1257
2 жыл бұрын
Ottima spiegaziome
@autodocuk
2 жыл бұрын
Siamo contenti che i nostri contenuti ti piacciano!
@zsoltsvelta
Жыл бұрын
Jó nektek csakugy leesik nekem azért kérte avésőt meg a 🔨
@autodocuk
Жыл бұрын
Tisztelet nézzünk, Köszönjük a megjegyzését A videó csak tájékoztató jellegű és emiatt azok a részek ami egyértelműen nyilvánvalók ki vannak hagyva, hogy rövidebb legyen. Tisztelettel AUTODOC csapat.
@ridds777
3 жыл бұрын
Incorrect method of replacement. The steering spindle did not need to be removed from the strut. Invest in proper tools to do the job properly without unnecessary steps.
@Strange_92
Жыл бұрын
Well, sometimes it helps to have less stuff in the way, even if it is unnecessary to move that stuff out of the way.
@ridds777
Жыл бұрын
@@Strange_92 work smart, not hard.
@Strange_92
Жыл бұрын
@@ridds777 exactly.. sometimes it's just smarter to remove some stuff out of the way, if possible. Not too much, obviously.. I work on my own car, as I have enough knowledge, I got a vocational education on this stuff. I'm not saying that I'm the best mechanic, but I do know stuff.
@ridds777
Жыл бұрын
@Strange_92 removal of unnecessary parts is a waste of time. If your time is not valuable to you, then that's on you...
@Strange_92
Жыл бұрын
@@ridds777 depends on what you remove.. and when I'm working on my own car, I'm not doing it on such a hurry. Not too slow either...
Пікірлер: 41