This video is much easier and simpler to follow than the others out there! Thank you!
@GreenLea24
2 жыл бұрын
Thanks a million times over. My bulb was hard to turn. So I grabbed my scarf in the car and used it. Finally got it to turn. Where is a man when you need one lol. Ladies we can do it too! Thanks again! 🙏🏾
@quesadajeremy9273
2 ай бұрын
KZitem certificated 😊
@roar8693
17 күн бұрын
Haha broke single mom here gonna start fixing my own car... who knew wed add mechanics to all the list of chores but here we are 😂
@dochort21
3 жыл бұрын
If you push the center of the rubber seal (push the dome in), the seal comes out more easily.
@TheArcher888
Жыл бұрын
Thank you for this video. It’s Saturday my low beam headlight was out ,and all automotive shops are closed and I-have to drive my car to work tonight. I decided to do it my self using your KZitem video, God bless you!!
@hembieashwe7446
2 жыл бұрын
Wow!!! Thank you so much for this!!! Going to do it myself. Went to the dealer and they were going to charge me $47 plus taxes and the price for the bulb. I am so empowered right now. Thank you!
@ronj9448
Жыл бұрын
So easy! And I didn't even know how to pop the hood before watching this. Bravo!
@cynthiareyna1457
11 ай бұрын
Easy and simple video. Straight to the point. Was able to replace my moms light bulb 💡 on her car.
@gak0090
Жыл бұрын
Thanks for the video- although the passenger side is way harder to do. The coolant reservoir is in the way (for the low beam on that side), and it' attached with clips which are impossible to get to. Finally, I had my daughter help me. My hands are not huge by any means, but trying to fit your hand back there with the coolant reservoir in the way has to be impossible for an adult man.
@waynemiller6945
8 ай бұрын
Removing the front clip only is not enough for big hands. You will need to brut force a flat head screw driver between the back of the back clip (metal post) and the plastic retainer of the coolant overflow tank. The back clip (meal post) has a small metal tab holding the tank in place. Once the Screwdriver is allowing the plastic retainer to slide past or over the tab, lifting up and removal of the tanks is relatively easy. I found removing the tank from the back clip first worked best. The tank can then be placed over about a foot without needing to remove any hoses. Reinstallation is as simple as forcing the tank back onto the tabs at the same time. I'm sorry I did not video the process.
@st.cimmerian1680
9 ай бұрын
Excellent video. Definitely the best one I’ve seen with how to do this. Simple, clear and straightforward. Subscribed!
@Beth9228
3 жыл бұрын
I just changed my highlights over couple hours ago. It was very easy for me to do.
@Kelly-ok8rg
Жыл бұрын
I used this video for my 2016 and it was a quick simple job. Thank you!
@lamonthattley23
3 жыл бұрын
This was good advice and big help made it look so easy 👍🏾
@simplyrvlife
8 ай бұрын
Wow, that looks easy. I have the confidence to try it myself now. Thank you
@davidkostuk7872
11 ай бұрын
For those looking for a solution to changing the passenger side headlight bulb. Here is what you have to do, no tools...works with big hands too! Step #1, gently take the coolant overflow tank off it's front clip, by pulling it upward and off the small metal post, this will give you about 2 more inches of room to get your hand into the headlight assembly. Step #2, remove the rubber cover off the back of the light. Step #3, unclip the power to the bulb and remove it. Step#4. Put a new bulb into the assembly and lock it into position. The plug and socket will nicely line up. Step#5 Just guide the plug into the socket and squeeze them together until you hear that nice click. Step #6, put the rubber cover back on and put the coolant overflow tank back onto its clip.
@tigeabenton2174
10 ай бұрын
So it’s a tad bit more work and that’s why he didn’t choose that side to fix? Thank goodness my driver side is out. But I want to change both to match 😐
@waynemiller6945
8 ай бұрын
No. Removing the front clip only is not enough for big hands. You will need to brut force a flat head screw driver between the back of the back clip (metal post) and the plastic retainer of the coolant overflow tank. The back clip (meal post) has a small metal tab holding the tank in place. Once the Screwdriver is allowing the plastic retainer to slide past or over the tab, lifting up and removal of the tanks is relatively easy. I found removing the tank from the back clip first worked best. The tank can then be placed over about a foot without needing to remove any hoses. Reinstallation is as simple as forcing the tank back onto the tabs at the same time. I'm sorry I did not video the process.
@RealJayPowell
8 ай бұрын
you only get about 1/2 inch if you only pull it off the front clip. Don't know how you possibly got 2 inches.
@sunnyd-lyte2008
3 жыл бұрын
Thx a bunch! I just changed my passenger headlight. Easy peazy 👍🏽
@mythicalgiraffe8830
4 жыл бұрын
Well that was incredibly easy. Thanks!
@LJFamilyTime
Жыл бұрын
Thank you for saving me money, time aand anxiety!
@scottscali
Жыл бұрын
Thank you sir changing my fiancé’s headlights today to LED lights.
@nadiacontreras2456
Жыл бұрын
Thanks for the video! It was super easy to do it myself Thanks to you.
@CampingTherapy
2 жыл бұрын
Thanks for showing this. My headlights are very dim, and I want to replace them with brighter lights.
@serendebbied
Жыл бұрын
Thanks. Got this done in less than 5 minutes once I had the part.
@romamotion
2 ай бұрын
Thank you very much! Very easy. i changed my lamps in 10 minutes =)
@deontepage8849
Жыл бұрын
My light had went out driving three Kansas at night this video help me out alot🎉🎉🎉🎉🎉
@coloradostrong
Жыл бұрын
_Alot_ is a town in India. _A lot_ is more than one of something; multiples of.
@clintonearlwalker
2 жыл бұрын
Outstanding!! I have to do this in a day or 2, low beam just conked out.
@sharathsuresh4625
6 ай бұрын
Can we replace the bulb with LED one ? If Yes, which led bulb to buy ?
@msfergie75
Жыл бұрын
Thank you so much! So much easier then thought.
@monicaabel1989
Жыл бұрын
Thank you so much, that is much easier than I thought!
@xKrulex
4 жыл бұрын
This helped a lot, I was trying to turn the harness out before Appearently...I was like WHY is the bulb so high up where I can’t take it out? F$&king Ford!! Now I feel silly lol.
@colinmorgan7771
4 жыл бұрын
need a midget set of hands for low beam on passenger side the reservoir has to be moved to do low beam on a 2017 escape
@jimhughes1070
2 жыл бұрын
I'm watching the mechanics in the bay in there removing the entire front of the car... Why is my belly burning? 🤣🤣🤣
@ViolentDetour
2 жыл бұрын
The fact you did 95% of this with one hand proves this is easy!
@46krock
Жыл бұрын
Nice, simple, understandable. Next please😁
@ImGettinWeird
2 жыл бұрын
Gotta change mine tomorrow. Thanks for the video !
@kathaus9688
3 жыл бұрын
You are the BEST! Thank you for the perfect video and instructuon! I did it!!!!!
@trinashappyplace2773
8 күн бұрын
Thank you. You are my hero.
@philhutchinson2591
Жыл бұрын
You may need the H11 bulb or the 9005 bulb, depending on your model. I have the SE and needed to 9005. Pull your bulb first to be sure. Btw, the 9005 is a longer buib and harder to remove. I assume the assembly is designed for the shorter H11 bulb but some a-hole engineer switched to 9005 without a care how the customer would be affected. I could not get the rear reservoir clip to release. From a tip in another video, I made a string lasso and was able to pull the wire harness into place and snap the bulb in. I did after getting the tip of the bulb into the hole but prior to seating it fully and twisting it into place. All-in-all, a horrible design, as is the battery location on this vehicle. A customer should not have to take their car to a mechanic for these simple tasks.
@kevinmiller6009
Жыл бұрын
On my 2014, the 9005 is the inner high-beam and the H11 is the outer low-beam.
@jacksmith785
11 ай бұрын
@@kevinmiller6009 That's what my dealership told me too - and the fog lights are 9145, in case someone needs to change that as well.
@tigeabenton2174
10 ай бұрын
@@jacksmith785thanks
@tigeabenton2174
10 ай бұрын
Thanks 😊
@tigeabenton2174
10 ай бұрын
@@kevinmiller6009thanks
@gerryduggan6821
Жыл бұрын
Great thanks brilliant job ! Now I know how to do it ! Keep making videos! I'm now subscribed 👍
@FROGSHAIR
2 жыл бұрын
I have been told to always wear gloves(latex) when working with this type of lightbulb. I was told the human skin touching the glass could ruin the lightbulb. Is this true? If so, why didn't you? If not, why not?
@JB-jf3ke
2 жыл бұрын
Oils on your skin get get on the bulb and possibly ruin the bulb,always use a glove or papertowel
@sweezy7455
2 жыл бұрын
Perfect explanation. Thank you.
@barbpatrick-broadbent6972
Жыл бұрын
Thankyou for this video. It helped so much
@oneshoe123
Жыл бұрын
That was easy to follow, thanks for the video☺
@destruth7669
2 жыл бұрын
Quick and easy Thank you so much🙏
@SunTojo
2 жыл бұрын
Where did you buy the low beam for the car cause I can’t find it can you send me a link?
@oryday1133
2 жыл бұрын
Thanks much easier than I thought
@Ojeramup12
Жыл бұрын
THanks, I will change mine today.
@jennyhurst6807
Жыл бұрын
Very simple and helpful, thank you
@MexiLvz91
2 жыл бұрын
Hi, was wondering if you uploaded the one for how to change signal lights?
@jenniferramirez403
2 ай бұрын
So helpful this is!!
@jastorino
Жыл бұрын
For low beams make sure you get HB3 / 9005. H11 will NOT fit for low beams, at least on my 2017 SE
@rdepew61
Жыл бұрын
The me with me 9005 2017 SE
@BrianTheTrader
2 жыл бұрын
2014 Escape has two T10 screws that must be removed. And the power is on the bottom and also a bit hard to remove. I gave up at this point.
@joshuavanburkleo9513
Жыл бұрын
Brutal to not know that until I read it here lol.
@mikecrabtree3341
6 ай бұрын
Perfect! Thanks😊
@alexe407
3 жыл бұрын
Finally something easy to fix!
@Leftoverlasagna26
Жыл бұрын
Thank you for posting!
@y122075t
3 жыл бұрын
Is it normal for both low beams to go out at same time - possibly something else!?
@rebd00mer93
2 жыл бұрын
Anything is possible but thats why they recommend changing both bulbs at the same time.
@y122075t
3 жыл бұрын
Good, simple & detailed! Thx!!
@teamgreen404
3 жыл бұрын
Thanks for your post! So helpful! 👍👍
@jackstraw5527
2 жыл бұрын
The 2014 I’m looking at looks nothing like this. It looks way harder.
@Stephadamo
Сағат бұрын
TY kindest stranger
@Issamboch
Жыл бұрын
Thank you so much ❤
@apriltear3401
3 жыл бұрын
You Rock, dude. Thanks !
@andrewnava9633
2 жыл бұрын
Great video! 👍
@stephendverner
3 жыл бұрын
Thank you for this video. It helped.
@jordanpersad6368
2 жыл бұрын
Wow that is so easy! Thank you!
@markheidema3699
2 жыл бұрын
Thanks for sharing!
@150itsgherbobaby2
2 жыл бұрын
So what is the size for High beam? Please
@kingkampz3579
3 жыл бұрын
Thank you so much! Super helpful!
@barberdoug2012
2 жыл бұрын
Very Helpful Thanks!
@juliocruz3784
6 ай бұрын
Thank you!!!!
@jamesbroom7095
4 жыл бұрын
Yeah.. all the videos show it on the driver's side which is a snap compared to the passenger which is MUCH MUCH more difficult
@dailydrivencarsddc1182
3 жыл бұрын
How much more difficult?
@jamesbroom7095
3 жыл бұрын
@@dailydrivencarsddc1182 See Colin Kerry comments below.... that pretty much sums it up. Driver's side is a snap (15 min job at the most).... passenger side... well... with midget hands maybe 20-30 minutes... my hands.... much longer!
@FrederickPine73
4 жыл бұрын
Big help sir. Thank you!
@canuckitude
2 жыл бұрын
So the bulb I pulled out of this location says 9005 which has a wider space between the prongs. I searched my local parts store and they say it's H11 too... which has very close prongs..
@wesleymccoy870
2 жыл бұрын
I know the feeling! They say H11 for the high beams but H11 only fits the low beams on a 2017 SE the prongs on the bulbs are too far apart for the highbeams
@jastorino
Жыл бұрын
I just did my low beams on 2017 SE. HB3/9005 is what I pulled out and what fit. H11 would NOT fit due to the connector prongs being much closer, I tried.
@nabeelshatat3158
4 жыл бұрын
Thank you very much
@JohnDoe-556
9 ай бұрын
Thank you
@g.ellisii4232
4 жыл бұрын
Thanks bro!
@avici0182
3 жыл бұрын
Much appreciated 🙏
@arjay_2002
2 жыл бұрын
What about fog lights
@burninglion82
2 жыл бұрын
How to change the fuse for headlights
@daverobertson6795
3 жыл бұрын
Thanks!
@JaginTx
9 ай бұрын
Show the passenger side low beam replacement
@paulelester
4 жыл бұрын
How about doing the side that is hard to replace bulb ? You have to go to dealership to get it with special tools . Lame design Ford
@alohaXamanda
5 ай бұрын
Unfortunately this video isn't helpful for those of us with HID lights, not sure which specific models have those but they are about $130 per bulb and you need tools to replace them.
@Ronin8500
2 жыл бұрын
I would give you a like, if you would change the passenger side low beam!! There's a trick to the passenger side low beam.
@AlKiMisT1111
3 жыл бұрын
Thank you sir. Oh and I fixed it so you weren't at 666 likes anymore 👹😉😁
@paulgoyette9171
Жыл бұрын
Shouldn't you have gloves on? Not supposed to touch the bulb with bare hands.
@Duckleet-Website
Жыл бұрын
my is screwed in and has a metal plate behind it.
@EzioAuditore96
5 ай бұрын
What about the INFAMOUS passenger side where no man’s hand can reach??????
@baconsandyspringcustoms.2073
8 ай бұрын
There is a trick there is no slack on the passenger side
@tonybatista1928
4 ай бұрын
That's the easy side
@nurovisuals7350
2 жыл бұрын
Thanks! Bosnian accident ? Lol
@jimhughes1070
2 жыл бұрын
Don't you wish it was really that easy 🤣🤣🤣 our 2014 escape works nothing like that... In fact it appears as though they are removing the entire front of the car...(watching the bay from the big window at the dealership) 😬😳😳😳🙄🥴
@SlainteRacing
Жыл бұрын
This is lame like all the other ones. The passenger side is "not like the driver side" there is no space and no slack in the wire. No one shows that and glasses over it. Only one video I found does, took them an hour. Called Ford, they claim you have to drop the bumper? I so far have spent over 45 minutes attempting the passenger side. Driver side took less then three like this video.
Пікірлер: 127