For anyone watching this make sure you turn the key with the spring in one turn or force so as to make the spring stronger.
@ebbonfly
7 ай бұрын
Good point, you have to wind up the spring 1 turn or it will not flip open.
@gielrozilio4541
6 ай бұрын
Can you explain this better?
@raftonpounder6696
Жыл бұрын
It helps if you keep the subject in the frame.
@paulsauser7217
Жыл бұрын
great video thank you by changing the shell of the key my central locking no longer works the battery and good if someone could help me. THANKS
@MoooseBlood
2 жыл бұрын
Thanks man I just got a used 500 and the Fob looks like it survived a fire. Ordered the new one on ebay. Now we must wait.
@Elfak1989
Жыл бұрын
This video is not good. You need to do few extra things for the spring to work correctly and you need to move the key code into new case
@taraboor7942
Жыл бұрын
How do you do that?
@Elfak1989
Жыл бұрын
@@taraboor7942 i actually went to mechanic.. he did it in 10 sec, didnt even charge me…
@aleksandarvesic7491
Жыл бұрын
Very bad explained
@yokapok6490
2 жыл бұрын
qu'est ce qui dit le gars ?
@CaptainDCap
Жыл бұрын
In case your key doesn't close fully, you need to replace the big tear-shaped piece at the end of the key, also. To do this, you need to remove the pin connecting the piece with the actual key. To do this, you need a metal rod and a hammer. Make sure to not lose the pin, as you will need it for the replacement.
@GrandePunto8V
11 ай бұрын
Where is the immo chip? In the plastic? In the PCB (one of the IC's)?
@JulieFalconer-mx1zu
10 ай бұрын
So helpful!!! Thank you, just changed battery effortlessly
@sterichardson1992
3 жыл бұрын
Great video. Helped massively. Thank you.
@TheSnoopdog14
3 жыл бұрын
the most important part is the spring of the blade . once u put that on below the blade and then lock it in place ( the blade ) , u have to turn one turn with the cover ( after inserting the other spring from the top ) , correct ? there were two springs in each key , correct ?
@XayalTV
3 жыл бұрын
Yes, that’s correct
@alfonsosantoyojr.6132
2 жыл бұрын
Mine only closes with the button. It does not open with the button, what did I do wrong? Author never shows the right way during that step…
@MuttleyPT
3 жыл бұрын
Very helpful video. Thank you mate. I spent a little bit more and cut the new key blade as well.
@reverendodarn4295
5 ай бұрын
I used a blunt Stanley knife to carefully pry apart the inner clips so the inside shell comes apart, was much faster than using a screwdriver as shown, apart from that thanks for the video for showing how it all comes apart.
@BLUESKY-zt1nv
7 ай бұрын
what a bloody nightmare ..dont think i will even attempt this
@cookingwithadiyvlog8102
3 жыл бұрын
Great 👍
@Rickyfav
3 жыл бұрын
The transponder is in metallic part of the key? Thanks
@XayalTV
3 жыл бұрын
Yes
@cipcip5338
3 жыл бұрын
Thanks mate Really helpful
@nicolasfeuchter8687
3 жыл бұрын
Is there a time limit (disconnect the rest of they from the battery) which I have to look for? For example, after 10, 15 or xx minutes they will lose the programming?
@XayalTV
3 жыл бұрын
There is no time frame for this
@BlatentlyFakeName
3 жыл бұрын
That only happens on keyless cars
@tristancraven3685
3 жыл бұрын
There is a chip in the old key fob built into the plastic which is for the emobilizer on your vehicle . I bought one of these and found I had to put it back in my old one .
@maddybrooks4910
Ай бұрын
Is there any way you could explain what it looks like please? I know this was quite some time ago now though.. 🥴🥺
@teresaiche4722
4 жыл бұрын
Thank you very much
@gwizz9175
6 ай бұрын
Thanks for this, a job I'll be tackling shortly!
@andrewmorris2958
7 ай бұрын
Great video, made changing my key painless. Thanks mate 👍🙏
@keiracarla4576
3 жыл бұрын
Hi, can I have the link for the eBay one please
@XayalTV
3 жыл бұрын
** for Fiat 500 Panda Punto Bravo 3 Button Remote Flip Key Fob Case +logo *+A45
@elliskaranikolaou2550
Жыл бұрын
Good Job.
@bluestanley123
3 жыл бұрын
Was there any recoding needed after?
@tristancraven3685
3 жыл бұрын
They dont work as the emobolozer chip is built into your old key fob plastic
@nickholland20
Жыл бұрын
You don't need to dismantle the metal key portion from the spring component.if you look thete is a small roll pin that holds the key blank to the mechanism.if you drift this out and also on your original key,just swap them over,redraft in the little pin and bobs your uncle.use a thin panel pin to knock the roll pin out.
@maddybrooks4910
Ай бұрын
Magic! I had just been wondering about this. I was a bit concerned about the pin then being loosened although it looks as though one side of the pin may be slightly wider than the other but it may be a trick of the eye? Thanks for this tip ☝🏼💖🐥✨
@FMFGUF
3 жыл бұрын
Very helpful video, thanks. I managed to fix the non-working door opening button on my Abarth Grande Punto keyfob; a PCB track had been broken, where the battery terminal swings into the casing (a rather poor design).
@Ricardo_KillSwitchPT_Lopes
Жыл бұрын
thanks, it worked perfectly
@MLCProducer
2 жыл бұрын
Has no idea what to do 😂😂
@davidpetty9588
2 жыл бұрын
Did it work ok on the car when finished?
@XayalTV
2 жыл бұрын
Yes
@hudsonbonfim9243
Жыл бұрын
HuDsoN
@fatonor.9613
Жыл бұрын
7u
@THEPOWER99FM
Жыл бұрын
Pain in the ass it is I rather just have a professional do it🤙
@landwomble
3 жыл бұрын
really helpful, took me 30 secs and it looks like new. Thanks, my daughter's dead chuffed
@pauls826
3 жыл бұрын
Cheers wanted know how do this with mine next question...... why are you driving a birds car
@maddybrooks4910
Ай бұрын
I really want to know if it worked after prising out the circuit board with that lil micro flathead screwdriver? I’m looking at doing this myself but was thinking that a plastic modelling tool may be a safer bet for that part of the process …🙄❤️🩹💭🐥✨
Пікірлер: 55