01:01 - Use a drive socket No.17. Unscrew the lower fastener of the shock absorber. 02:03 - Remove the luggage compartment trim panels. Use a flat screwdriver. 02:41 - Use a combination spanner No.17. Use a adjustable spanner. Unscrew the upper fastener of the shock absorber. 03:30 - Before installing a new shock absorber you should pump it manually 3-5 times. 03:47 - Install the dust sleeve and the bump stop on the new shock absorber. 04:30 - Tighten the top shock absorber fastening. Use a combination spanner No.17. Use a adjustable spanner. 06:14 - Use a drive socket No.17. Tighten the lower fastener of the shock absorber. 🛠️The tools you need to replace shock absorber: - drive socket No.17 - flat screwdriver - combination spanner No.17 - adjustable spanner
@edenf7704
2 жыл бұрын
Great video. Took me about 2.5 hours to do it, very simple. Just make sure to replace the bump stop and vibration damping (Sachs 900 180).
@autodocuk
2 жыл бұрын
Thank you very much for your feedback. We are glad that our video was useful to you. AUTODOC
@ewanrollo5527
5 жыл бұрын
Thanks again. Really useful video for me.
@autodocuk
5 жыл бұрын
Thank you for your feedback. We are happy to know you like our videos.please stay tuned with us that not to miss our news. Best regards,Autodoc!
@Adam-7_7_7
2 жыл бұрын
Top clip mate , clear instructions and tuition - like all your clips 👍
@autodocuk
2 жыл бұрын
Thanks for your positive comment! Stay with us!
@futurecarslondon1109
3 жыл бұрын
Thanks for your help.
@ianpurcell7266
2 жыл бұрын
Replace the dust cover and bump stop and lower shock to lower hub fastener.
@PaulMoorhousehankooks
4 жыл бұрын
Could have cleaned the shroud
@tsiva7tsiva456
Жыл бұрын
Swift dzire tp2 modal dikkey water leakage problems vedous plz
@videocrackent.3486
3 жыл бұрын
Is the supose to be litle movement after fastening the bottom screw on the shock .?
@autodocuk
3 жыл бұрын
Thank you for your comment! Please clarify or rephrase your question. Best Regards, Autodoc team.
@MrCopRobo
2 жыл бұрын
Torque wrench not needed
@josephsebastian8380
6 ай бұрын
❤❤
@serdarsonmez7548
5 жыл бұрын
Can you show we something relevant with corsa D.
@autodocuk
5 жыл бұрын
Thank you for your feedback! Unfortunately, we didn't work with Corsa D . Best regards, Autodoc.
@Barrygee
2 ай бұрын
I changed mine but now something is rattling at the back of the car…everything is done up tight so i have no idea whats causing it but its only started since i changed shock absorbers
@autodocuk
2 ай бұрын
It’s difficult to say anything without proper diagnostics; we recommend contacting a service center.
@Barrygee
2 ай бұрын
@@autodocuk i figured it out, i had tightened the top nuts up far too much and compressed the rubber mounts. I loosened them off a bit and the rattle has gone away. There really should be some sort of guideline for tightening them, I assumed they out to be very tight but they clearly shouldn’t be.
@autodocuk
2 ай бұрын
In practice it is important to use a torque wrench and keep the appropriate tightening torques to avoid undesirable consequences.
@Barrygee
2 ай бұрын
@@autodocuk well i quite agree but since there are no torque settings given in the instructions for the shock absorbers nor do you suggest any torque settings in your videos its hard to know what torque to use. It’s also not so easy to use a torque wrench as you need to grip the top of the strut to prevent it turning whilst tightening, therefore you can’t use a conventional socket and torque wrench and have to use a spanner. Please explain how to measure torque while fitting a rear shock absorber such as this.
@sasaokic7058
5 жыл бұрын
Врх ! ☺
@autodocuk
5 жыл бұрын
@Sasa Djokic Thank you for your feedback! We are grateful that you watch and comment on our videos. You are our devoted follower. Please, send us an e-mail and we will forward you our gift certificate for 50 EUR for purchases through our website. Best regards, AUtodoc.
Пікірлер: 26