Excellent no-nonsense video. Good job! Very professional. Thanks!
@lookherejack
3 жыл бұрын
Just wanted to say thank you, this video was very helpful to me. I couldn’t have done it otherwise. Much appreciated good sir!
@SmooothShifter
3 жыл бұрын
Thanks. I had a hard time getting the wheel off as it was older than the one in the video. Old motor had a green wire, and I don't think it faded from blue, but I just used it and it seemed to cycle fine. First fire up didn't work because I didn't have the impeller wheel far enough in and it was pinned to the outside housing. Anyhow, it took me longer than 10 minutes, but I don't do it all the time. Appreciate the video.
@greggo502
11 ай бұрын
Steve, It's guys like you that make KZitem. GREAT!!! Changed out my motor ,everything works fine. Only thing I would add to anyone doing this is its a little easier with a long allen wrench taking off the motor bolts And my old motor had a brown wire ,where the new motor has a red wire (stumped me for a second but only a second Lol) Fantastic video Steve!!
@chunweihsu3157
Жыл бұрын
Dear Steve, I just replace my motor this morning following your video step by step. thanks a lot.
@Solderwire
5 жыл бұрын
Just about to change one of these for a customer, thanks for the heads up.
@arejaz21111
Жыл бұрын
Thank You Bud!!!! i managed to (atleast temporaryly) fix my burner. Bearing was almost seized, i sprayed WD40 just a teeny tiny bit and bearing goes nice and loose, its stable, not wiggling so gonna put back to work:) Would be great if you put a video gow to extract and press back the bearings. Your video was vital so i can dismantle it. Did it 1st time and assembled back thanks to your video.
@b0dycounter
5 жыл бұрын
This was very helpful. I just wish you would have talked through the different size tools needed. torx sizes, wrench sizes, etc. but thanks for your work.
@Sisyphean
4 жыл бұрын
All I needed were 4mm hex for the pump, 5mm for the motor and #2 Phillips in order to change out the pump. My blower impeller was secured with a 4mm hex screw and there was a notch in the fan blade for my wrench to pass through to reach this screw. My t-handle hex wrench wasn't long enough to be outside of the burner ass'y back case so I broke the back motor screw loose and used a standard 4mm to spin it out. I realize this is too late to help you but I figured I'd share this for those that follow.
@NewsYourViews
3 жыл бұрын
Very helpful thanks 👍👍👍
@kennyg1808
5 жыл бұрын
u just just saved me a couple hundred dollars ...perfect video ..thank you!
@willys7974
2 жыл бұрын
This guy is good 👍🏽
@sirhc07
3 жыл бұрын
A motor on a beckett burner is a hell of alot easier to replace 😆
@chunweihsu3157
Жыл бұрын
Dear Steve, I plan to replace my noise one before it breaks down. Would that possible you share name of the T Shape tool with loop on top? thanks for your video.
@Kiangaf
3 жыл бұрын
The fan is nearly always seized on in my experience.
@stevemacphail888
Жыл бұрын
Hold the motor shift after you remove the pump and slowly turn the fan .it will loosen
@thanosied
Жыл бұрын
@@stevemacphail888 what if the fan is secured with a round bolt with a allen shaped screw on the side? I removed the allen shaped screw, but the round bolt won't budge
@stevemacphail888
Жыл бұрын
@@thanosied should only be an allen key holding fan on shaft .nothing more .hold the motor end and turn the fan back and forth
@josephpalermo5626
Жыл бұрын
Question are their hex screws metric?
@stevemacphail888
Жыл бұрын
To be honest I'm not sure I would say yes as they are Italian
@josephpalermo5626
Жыл бұрын
@@stevemacphail888 that’s what I thought. Thank you.
@Ratman_Bejo
3 жыл бұрын
Hello sir, why is this the motor burner?
@stevemacphail888
3 жыл бұрын
Yea motor change
@doublewide420
4 жыл бұрын
Aquastat on the burner,wtf does that
@stevemacphail888
4 жыл бұрын
Not sure what you mean
@wildepiper
4 жыл бұрын
the control on the side of the burner is not an aquastat ,its where the thermostat is hooked to turn on the burner.
Пікірлер: 28