Finally I understand how to chose the tolerances after 4 years of studying mechanical engineering, thank you
@basavarajm5196
19 күн бұрын
Hii bro this is basvaraj..this is wonderful video for all design Engineer.. before i saw in this video I don't know how about tolerance? How to put tolerance in dimensions..but now i have known how about tolerance... thank you very much for bringing up this video..❤
@mechanicalvault
15 күн бұрын
Great to know that it helped you 👍
@3dModelDesigner
Ай бұрын
Excellent video❤
@mechanicalvault
Ай бұрын
Thank you 😊
@RAHULR-uf4vh
3 жыл бұрын
You have clarified a doubt that I had for past 2 years. Thankyou very much Sir.
@mechanicalvault
3 жыл бұрын
Glad that it helped you!
@TheMonkeygrunt
3 жыл бұрын
You have no idea how much I'm geeking out right now. I'm so excited i found this channel!
@mechanicalvault
3 жыл бұрын
Thank you DD's Berries!
@siskel2689
3 жыл бұрын
Great video.
@ShibudasCK
3 ай бұрын
EXCELLENT VEDIOE
@mechanicalvault
2 ай бұрын
Thank you 😊
@ravimukati2422
2 жыл бұрын
This is exactly what I was looking for. Thanks for bringing up this video sir.
@Arunkumar-mg9uz
3 жыл бұрын
Ofcourse we likes your video Really informative. THANK YOU
@mechanicalvault
3 жыл бұрын
Glad that you liked my videos!
@dineshd2988
11 ай бұрын
Much knowledgeable video..
@mechanicalvault
11 ай бұрын
Glad that you liked it ✨️
@MukeshKumar-ov8iv
8 ай бұрын
Thanks you sir
@mechanicalvault
8 ай бұрын
🙏🙏🙏 Welcome
@satindersaini8055
3 жыл бұрын
Well done sir thanks for this informative lecture And make more videos on standards used in manufacturing industries
@mechanicalvault
3 жыл бұрын
Glad that you liked it!
@beautyofnature9848
3 жыл бұрын
Thanks for your valuable time and information, my doubts getting some clarifications
@williamcase426
2 жыл бұрын
Great video
@mechanicalvault
2 жыл бұрын
Thank you!
@roxrtk3299
3 жыл бұрын
finally i found a great channel...
@devashishmishra7230
3 жыл бұрын
Thankyou for bringing such great content....very rare to find such channels dedicated to Mechanical Design Engineer.
@gamesnstuff3075
3 жыл бұрын
Thanks for this video 😊
@SuperJJ37
5 ай бұрын
Great job as always!
@mechanicalvault
5 ай бұрын
Thank you 😊
@shivalingappaspatil4746
Жыл бұрын
I'm so glad for this video, really liked this video a lot Thank you so much sir
@erjatinder5762
Жыл бұрын
Great work sir please make more videos 👍
@ferdusalamfahad8348
Ай бұрын
thank you
@gorthisidhardha27
2 жыл бұрын
super sir u converted my confusion to clarity
@mechanicalvault
2 жыл бұрын
Thank you 🙏🙏
@decentgaming1122
2 жыл бұрын
Very good video bro
@mechanicalvault
2 жыл бұрын
Thank you!
@kamleshvasava7320
2 жыл бұрын
Superb sir , I am struggle to find this thing. you made my day. Thanks
@mechanicalvault
2 жыл бұрын
Glad that you liked it!
@srigandhak8913
Жыл бұрын
Thank you so much sir, very easily explained
@maastimaaza
10 ай бұрын
Thank you very much sir. As a design engineer in manufacturing. It is really helpful video.
@mechanicalvault
9 ай бұрын
Glad that you liked it ✨️
@anilwins6415
Жыл бұрын
Thankyou bro_
@mechanicalvault
Жыл бұрын
Welcome always 👍
@mohitbhave1004
3 жыл бұрын
Very well explained, Sir
@mechanicalvault
3 жыл бұрын
Thank you Mohit!
@shoebqureshi7359
2 жыл бұрын
awesome video
@nishantdhengre9396
2 жыл бұрын
Excellent.
@nomanafridi5503
7 ай бұрын
Thanks
@maheshpeddinti4645
3 жыл бұрын
Thank you soo much Kevin👍
@mechanicalvault
3 жыл бұрын
👍👍🙏🙏
@Andersonsanjay1
3 жыл бұрын
Good explanation
@hiteshkale888
3 жыл бұрын
Sir thank you🙏 for this video
@aniketgade1272
2 жыл бұрын
👍
@Onkar14
2 жыл бұрын
Sir, Very informative. I would like to see more videos on design from you.
@Abss0966
Жыл бұрын
I like the intro music lol
@mechanicalvault
Жыл бұрын
And what about the content 🤔
@changw_w9413
Жыл бұрын
Thank you for providing such a great video. I have a question Sir, how do you know if the tolerance stated in the table is equally disposed on the basic size? Could the tolerance be unilateral (+x / +y) instead of bilateral (+/-x)? Thank for reading my question.
@omkarparab9226
2 жыл бұрын
It is required to compute the limit dimension for an interference fit on the shaft basis system for a basic size of 30mm diameter, with a negative clearance of 0.20 mm, tolerance on hole 0.025mm and tolerance on the shaft 0.050mm. (ans)
@voductaitran7587
3 күн бұрын
hi, may i ask. for IT12, is it acceptable to add the tolerance tighter (into IT11) or looser (into IT13) in the drawing? If the drawing specific that we must use IT12, is tighter or looser acceptable or not ? Thank you
@enochtayengwa2895
2 жыл бұрын
🙏 thank you
@PRATIKSUMAN-vu9rx
6 ай бұрын
Can you Please explain me ,if the plastic part is made up of Injection molding so it's Grade is IT12 TO IT 14 ,SO WHICH ONE IS SELCTED FOR TOLERANCE AND WHY ?
@mechanicalvault
6 ай бұрын
You can start with higher grade if allowed by function and reduce the tolerance if needed.
@venkatsureshmedishetty657
Жыл бұрын
Why higher tolerance is given to larger dimensions? Please clarify
@sandhoshkumar162
3 жыл бұрын
Gud mrg sir let me know that other mfg process tolerance for sheet metal component like rolling, bending, oxy cutting, plasma, ..etc
@amolaegade5428
Жыл бұрын
can anybody explain why fits weren't considered anywhere in this video to arrive at tolerance values....in this video tolerance values were selected on the basis of manufacturing process but don't you think selecting tolerances based on fits is more appropriate compared to that...
@mechanicalvault
11 ай бұрын
If we have mating feature in design which form engineering fit, then it makes sense to choose IT grade based upon function. But most of the dimensions and Tolerances on the part may not form the engineering fit, so in those cases, simply select the cost effective manufacturing Process and relevant IT grade.
@amolaegade5428
11 ай бұрын
@@mechanicalvault understood thanks for your reply
@KarthikeyanEkambaram-om4wt
2 жыл бұрын
Where we can find the IT grades for manufacturing process is there any standards for selection ?
@ajaykrishna8715
3 жыл бұрын
Sir which book we will get value of IT value and for all manufacturing process Which IT grade??
@bhaveshmishra5629
2 жыл бұрын
DEAR SIR CAN U PLEASE MENTION FROM WICH BOOK YOU HAVE TAKEN THIS DATA. THANKYOU
@kaleshkumark.s.5092
3 жыл бұрын
Hi Sir, Is there any other standards for Inch based Drawings?How can we define gen.tol for Inch dim.?
@dorcasandthesibs
2 жыл бұрын
I found this video very informative: kzitem.info/news/bejne/0mN6xWumsqtyeaQ
@keshavkapadnis8782
3 жыл бұрын
Good morning Sir when we select tolerance then that time why divided by 2 . Can toy explain me details.
@ashwads
Жыл бұрын
it's not supposed to be divided by two, after we get the tolerance value, then we need to find either the upper limit or lower limit. there are more table comes to find that... infact i missed the book and forgot how exactly it's done
@mukundkumar5996
9 ай бұрын
Hii sir, I want to take training from you so please guide how contact with you??
@mechanicalvault
9 ай бұрын
Please connect to Jagadish - (M) 8329029492. He will help you to get all course information.
@rohithmylada1616
3 жыл бұрын
I have a small doubt. Is it ISO 286-1: 1998 or 1988?
Пікірлер: 81