I’m happy to see one person do this in English..thank you great video
@diypotentials
2 жыл бұрын
Thanks!
@Vikitech5
2 жыл бұрын
If you have more videos like this send me the links
@diypotentials
2 жыл бұрын
@@Vikitech5 you can click on my channel logo for more DIY projects. Thanks!
@vibyvargas
4 ай бұрын
Thank you sooooo much dude my son is so happy I was able to wire it up all because of how you explained. Thank you
@diypotentials
4 ай бұрын
I’m glad it was helpful. Thanks!
@joelcortes6040
3 жыл бұрын
Honestly this type of controller is intimidating. Just looking wires everywhere don't know where to start. But this guy made it so simple. Thanks for sharing 👍
@diypotentials
3 жыл бұрын
Thanks 😊
@jrebuilds
3 жыл бұрын
Great video! really helped me understand some of these controller that don’t really give any markings on their wire. Will help me for my project. Thank you!
@diypotentials
3 жыл бұрын
Glad it was helpful. Thanks!
@unitedforce6264
Жыл бұрын
I just started to get into electric bikes, and your videos explain so much. Thank you so much
@diypotentials
Жыл бұрын
Awesome! I’m glad it was helpful..
@cosmicwanderer4306
2 ай бұрын
Thanks for sharing. I'm planning to use just the batteries, a DC/AC inverter, the 24V DC motor and a permanent magnet generator (output of 220V). The motor will power, (rotate), the permanent magnet generator. I will get current from generator to feed my equipment and feed the inverter which will keep my batteries up to the task. I hope to reduce my energy costs and be ''off-grid'' at least 80% (eventually). Energy costs are sky-rocketing and will prevent any ''hit to my pocket'' down the road. Again, thanks for sharing.
@diypotentials
2 ай бұрын
Best wishes! Thank you!
@safarijonas3490
3 жыл бұрын
Thank you! VERY well explained with good lighting and organization.
@elijahpd7000
2 жыл бұрын
This tutorial is awesome and very helpful, thank you so much. please make a tutorial on how to use the REVERSE and the BRAKE cables connection. Thanks!
@williamvan909
3 жыл бұрын
Out standing videos 👍👍👍 this will help me with My E-bikes great job thanks again for your help
@diypotentials
3 жыл бұрын
I appreciate the nice words. Thanks!
@hegazyhegazy3381
3 жыл бұрын
@@diypotentials Can you help me calculate the maximum weight that I can carry using that motor and with the same control and batteries please
@Jademyheart
3 жыл бұрын
Thank you 😌 as everyone says! Brilliant upload, learnt something fascinating & very cost effective!! How good is this guy 👌👍💯
@AlexandreMMadeira
Жыл бұрын
I have the same exact throttle but my controller doesn’t have ignition wire. Any solution? Your video was the best a saw so far on the topic.
@omarfa4337
2 жыл бұрын
AWESOME VIDEO !!. . The only thing I can think of would be if you added timestamps for each parts of the video. Hope that helps
@YagwitOG
2 жыл бұрын
Best Tut we have ever watched. Thank you!!
@diypotentials
2 жыл бұрын
Thanks so much!!!
@DougDiLaura
7 ай бұрын
Thank you very much sir. Excellent Video and very clear. Helped me very much in my conversion project.
@diypotentials
7 ай бұрын
Thank you!
@missmary2858
3 жыл бұрын
exactly what i was looking for
@diypotentials
3 жыл бұрын
Thanks! Take care...
@hrcsteubenville2187
3 жыл бұрын
I have an escooter that just died. I installed new batteries and I get nothing. How can I trouble shoot the controller. You are the best in explaining how things work and troubleshooting. Thanks for your videos.
@diypotentials
3 жыл бұрын
Sorry to hear that about your e-scooter. There are so many electronic components and parts involved that it is hard to pinpoint the problem. It could be the controller, a blown fuse, the hall sensors not working, or a wire not connected properly to the motor. I saw several videos that might be helpful for troubleshooting the controller. kzitem.info/news/bejne/xqxosGqfqmelZ5w, kzitem.info/news/bejne/zYqp2Xekbouqh6w, kzitem.info/news/bejne/r4SqrX6JZpx4l2k&pbjreload=101. I hope this helps. Thanks!
@shivdayalbhandari4069
3 жыл бұрын
Thanks of lot I cont connect the connection properly I watch our video now ok thanks again
@diypotentials
3 жыл бұрын
That’s awesome! Thanks!
@GRAHAMAUS
Жыл бұрын
@1:19, just to clarify what you're saying. The Hall sensors provide feedback on the rotor's position to the controller, so that it can properly drive the main phase connections. The Hall sensors do not create or manage the torque, that is all done by the main phase windings. The current in the Hall sensors is tiny -- a fraction of a milliamp.
@diypotentials
Жыл бұрын
Thanks for that clarification. You've explained it much better than I did. @1:35-2:00 I explained that the hall sensors collect information by sensing the magnetic field of the rotor, from there the sensors would inform the controller to provide specific magnetic field to interact with the rotor, meaning that the controller would release the electricity needed from the battery to generate the magnetic field in the specific stator poles or phases, therefore would generate torque against the magnetic fields of the rotor. You are absolutely correct, the current in the hall sensors is tiny. Thanks again.
@MrNigel1340
Жыл бұрын
An excellent tutorial, thank you very much.
@diypotentials
Жыл бұрын
Thank you!
@vjajmjrj
8 ай бұрын
Hello, I am interested in buying one of these, I notice on the web page it says there is a charging wire .. Is there a way to know when charge runs out? Also for a 12V battery, how to know if charge is low and how to charge? thank you sir
@mjohnsmith9529
Жыл бұрын
Could you make a video on how to change or upgrade a 48volt 1800w system to a 3000w 72volt conversion.. 2023 question
@tiitus4179
3 жыл бұрын
Hey, thank you so much, this video saa really helpful, thank you
@diypotentials
3 жыл бұрын
Awesome! Glad it was helpful. Thank you!
@xiaosun9111
3 жыл бұрын
great video!
@diypotentials
3 жыл бұрын
Thank you!
@bbrescia11
2 жыл бұрын
Thank you sir! I have a throttle grip with a cruise control function - and I have exactly the same controller you show in this video. How do I hook up the grip's cruise control to the motor controller? Thanks!
@ElKaylOfficial
11 ай бұрын
is it okey to use a 48V 600W motor to 750W DC Controller?
@diypotentials
11 ай бұрын
It should be ok.
@mh73672
8 ай бұрын
and 750w hub 48v motor with 1000w 52v controller?@@diypotentials
@randytinney6854
Жыл бұрын
Thank you for great video. But I have a question? How do you make that motor run in reverse? Thank you, Randy
@janickfrei4287
11 ай бұрын
simply change 2 of the 3 motor cables
@johngavina1
2 жыл бұрын
Im a little confused. So blue and yellow are powered. So what's the difference between the main power line and the small red line? Why does the switch curcuit need both wires powered? Shouldn't one go to ground?
@diypotentials
2 жыл бұрын
The way I understand it is that the yellow wire is a positive line for the switch, so it needs to be connected to the power source which is the red positive wire from the battery--So it is a parallel circuit. Coming out or at the opposite end of the switch is the blue line, which is still positive, that is why it is connected to the small red wire feeding into the controller, where the current will eventaully return to ground. It is very confusing. Maybe others can explain better. Thanks!
@Samuel-lm1wb
2 жыл бұрын
Awesome video, where would you connect the charger port to? Does it connect to the controller?
@moeznaseer5365
2 жыл бұрын
I think charger goes directly into the battery. The controller doesn't do this function. The BMS in the battery pack ensures that all cells are charged correctly.
@Samuel-lm1wb
2 жыл бұрын
@@moeznaseer5365 Hello, thank you for your help. let say I have a bunch of 18650 cells in series and parallel, do I connect the charger port to the cells? I was looking at this diagram. Would you be able to help? thanks esk8content.nyc3.digitaloceanspaces.com/uploads/db2454/original/3X/9/5/95b5b09076b1382f0cef10d579d75cbf6ea337ae.png
@diypotentials
2 жыл бұрын
The controller does not have a charger port. You can charge the batteries with separate charger. Check out my other video on how to charge a battery...kzitem.info/news/bejne/oqCql3migqlphJw. Thanks!
@Samuel-lm1wb
2 жыл бұрын
@@diypotentials THank you for your help. True I can do that but if I combined multiple 18650 cells in parallel and series, I don't think it's possible to charge them separately, how would I charge it in this case? I'll need a charger port right and where wold I connect the charger port to? Thanks!
@Samuel-lm1wb
2 жыл бұрын
@@diypotentials thank you very helpful!
@stefanogizzler
Жыл бұрын
Excellent video
@satyajitbhadraroy7723
4 жыл бұрын
Hi . Is it necessary to run this on battery? If it is driven with a 48 volt DC power supply (from AC to DC conversion circuit) will it not run? Or can get damaged? If it gets damaged please tell me the possible reasons. Thanks in advance
@diypotentials
4 жыл бұрын
I have not try using a AC to DC converter to run it. But as long as the supply output is DC it should be okay. Try it...let me know if it works. Thanks!
@Habibulla.M
3 жыл бұрын
Nice explanation 👍
@diypotentials
3 жыл бұрын
Thanks!
@mikaellind3940
2 ай бұрын
Great video, thank you so much. After I change my controller my ebike is not not running in full power, feels more like medium power. The 2 speed switch (low & Hi) is not working. No wires from controller is labeld. Anyone knows what color and how many wires it suppose to be out from the controller?
@hendog3894
3 жыл бұрын
Really well explained 😀
@diypotentials
3 жыл бұрын
Hello, were you able to wire your motor or do you still need help?
@hendog3894
3 жыл бұрын
@@diypotentials I have a 36v 11a rated current motor, 10s 5p (Samsung 30q) battery, along with a speed controller rated for 30a max.. I'm creating a 'light duties' power assist bike trialor.. hopefully the set up will work. I may need a more powerful motor.
@diypotentials
3 жыл бұрын
Sounds like you are set for the project. Your motor should be sufficient. The motor is I used for my Ebike conversion (kzitem.info/news/bejne/xGyPzYKHoGWHgG0) has a similar rating at 450 Watts. Good luck on your project. Thanks!
@rider2731
3 жыл бұрын
I believe the BLDC motors are also called EC motors (electronically commutated) motors. They are often found in fans in the air conditioning industry. They are preferred because of their energy efficient characteristic but they also cost more than PSC (permanent split capacitor) fans.
@diypotentials
3 жыл бұрын
Totally agree. Thanks!
@AlexandreMMadeira
Жыл бұрын
@@diypotentials My controller doesn't have an ignition wire and I bought a throttle with ingnition key and the throttle has three standard throttle wires and two more wires, the yellow and the blue (ignition) wire. Any thoughts on how to resolve this? Thank you
@guiterman6263
Жыл бұрын
Yes thank you dude i needed to see this
@diypotentials
Жыл бұрын
Thank you!
@simona.digruber9581
3 жыл бұрын
Hey great vid! Could you tell me please what is the name of the third not necessary connector is? The first is for the break and the second for reverse Thanks a lot!
@diypotentials
3 жыл бұрын
Speedometer is the single purple wire and the other red, black and blue wire connector is the pedal assist.
@yaminoshinn1473
2 жыл бұрын
Thankyou will try this , but.... I have both yellow wire for ignition connection at throttle , which one is blue can i connect in any one ?
@yaminoshinn1473
2 жыл бұрын
It works but my source is a weak dc (48 V; 2-3 amp ) adapter so couldn't get the full run as expected but excited for tomorrow to try it on charged batteries with enough power, thankyou once again \m/
@diypotentials
2 жыл бұрын
Awesome to hear it is working…
@yaminoshinn1473
2 жыл бұрын
Update: it's now on full throttle :D , worked for both 48 V n 60 V thanks a lot , but this 48 V 750 W seems only good for bicycles not so much torque but 60 V 1200 W will try for a quad bike upgrade soon it has promissing speed n torque let's see on field with the quad bike n load ... Thankyou once again was about to return those as was unable to get the controller ON .
@jones8732
2 жыл бұрын
@@yaminoshinn1473 @yami no shinn How do you connected the yellow wires? Is it a problem to mix them up? I have a yellow and a white wire at the ignition cable. Hope you can help me out! Thanks.
@yaminoshinn1473
2 жыл бұрын
@@jones8732 yes no problem it just provides a switching circuit for powering control box through ignition wire on control box which is connected to throttle wires (In my case yellow wires; in the video above yellow and blue ,assuming yours yellow and white ) i.e. If it's the throttle wire u are talking about . Though it might get reversely controlled( not definite ) in that case u can switch wires , anyways it won't have issues on control box try on low current output source first for more secure approach .
@spacefightertzz
3 жыл бұрын
Nice video. I was just wondering what the wires were to the motor. I'll need to watch this again when I look at my escooter. I did a quick fix on my kugoo m4 pro. I had banged/scrapped the wires that go to the motor. When I tried to accelerate then the motor would make like a vibrate noise and had very little power. So looking at the wires, I cut off the rubber protective and seen 2 thin wires were disconnected and the thick wires were fine. I connected the broken wires them by twisting together and duct taped it for now and scooter is working good. Just a quick fix until I get a soldering iron.
@diypotentials
3 жыл бұрын
Good job! Glad you fixed it. Thanks!
@Thekboys34
Жыл бұрын
Can you do a full part list how to charge the batteries?
@EmadeEasy
Жыл бұрын
Great video, how do you put a charge port and where
@leskeometv
Ай бұрын
Yo i have the brushless motor controler 48v and 250w, motor 48v 250w so max speed on e bike is 36kmh what to do on the controller to go faster
@NiazTechnical
3 жыл бұрын
Helpful information
@rays8307
4 ай бұрын
Best video ever
@gsrbooster
3 жыл бұрын
I just got the same throttle and was trying to figure out to how to connect it, so thank you for making this vid. Since the throttle has a voltage meter and it's directly connected to the battery, do you think a fuse between the two connection is necessary? I've seen some users do it with other voltage meters and others who don't.
@diypotentials
3 жыл бұрын
If you are connecting it through a controller, I don't think a fuse is necessary. I use the throttle on 36V 30AH lithium-ion battery pack without a fuse and no problem at all. Take a look...kzitem.info/news/bejne/xGyPzYKHoGWHgG0. Thanks for asking...
@pranavkrishna5119
2 жыл бұрын
How many kilometer can I run with this setup in a cycle
@freddykruger3320
Жыл бұрын
How is this controller rated for 48 volts, 30 amps and yet only 750w output? The output should be close to 1500 watts.
@michellekoete7881
Жыл бұрын
Very helpful
@othmanjorry1173
2 жыл бұрын
OOHH that great i appreciate you
@diypotentials
2 жыл бұрын
Thanks 😊!
@kafandosdonald4830
8 ай бұрын
hello, For acceleration, at the level of the average, I note that it is the principle of the potentiometer which is used. I wanted to know what voltage is used? is it 5V or 48V? thank you for answering me dear friend
@diypotentials
8 ай бұрын
It is the 48V. Thanks!
@nirmalaciniequipmentsprem8122
3 жыл бұрын
Super bro ... thanks....and also tell me what will happen ,if I connect the two wires in opposite direction...which is coming from throttle...
@diypotentials
3 жыл бұрын
It probably won’t turn on... Thanks!
@richardesposito6622
3 жыл бұрын
HI! Thank you soo much for sharing your thoughts with all of us re ebike controllers! I have a 2008ish 500watt 36volt AC hubmtr. with a 7 speed Shimano, throttle type ebike from the landfill! I can't find Battery, housing, charger and BMS and I believe the controller is in the hub. Connector to the battery has 6 pins 4 large pins and 2 small and the one to the hub has 5 small only two large pins. Spent hours of research, learning but still afraid to buy a possible battery, BMS and charger for it. I have had the ebike for months and I just want to go out get some exercise and experiment with this more. Also read I may need to change the throttle to a potentiometer type and I would need to getting bike rolling for the wheel to start rotating. Not a problem for me to do that and cooling down with fins or holes to stop any overheating is also. Cant I just get a get an LI 20 amp battery kit with BMS, charger with a SW/fuses and not the 30 amp controller you are showing here? I think I saw a 1-5 volt potentiometer on your other video but not sure where to get it? Way grateful for any thoughts on this!
@diypotentials
3 жыл бұрын
Hello, I'm not familiar with the hub-motor you described, so I won't be able to give any feedback on that. However, I don't think the controller is in the hub. There might be a hall sensor circuit inside the hub, though. But I might be wrong. Also since the motor is rated at 500 watts at 36V, it needs about 14 amps to reach 500 watts at 36V. So if you are planning on getting a controller, any one able to handle 14-20 amps or more would be sufficient, even the 30 amp one so long it is rated for 36V. For battery, a 20 AH (amp-hours) will be sufficient. Of course the more AH the battery has, the more run-time you will get. I found a video that might be more helpful..kzitem.info/news/bejne/om6HyYKsi5phqoI. Best of luck. Thanks!
@richardesposito6622
3 жыл бұрын
@@diypotentials Thanks again for looking at this and commenting here! With this I am getting a little more confidence on purchasing the controller you have here along with an Li battery/BMS and charger may just get it to work! I love that throttle you have here too! Not many frills on this ebike so just a Voltage reading is great for my needs. My mistake on the Hub Mtr pin out it's really a 7 pin push and screw on plug. There are 5 small male pins on it. I am guessing these may be 5 vdc for the hall sensors plus the throttle? Not sure yet until I test those leads and look further. If so what you are noting above makes more sense. I know it has a thermistor in the hub for overheating conditions but no direct pinouts for that. Enjoy your day and Kind Regards!
@fredricktroy1933
4 жыл бұрын
Current rating of 30amps. Is that the max amp it can handle or the max amp it is drawing from the battery?
@diypotentials
4 жыл бұрын
The controller is rated at 30A. The rated power is 750W and the rated voltage is 48V. If you are going to apply 30A, you have to lower the voltage level to 24V in order to meet the power rating (24V X 30A = 720W). If you are applying 48V, the current (amperage) should be a round 15A (48V X 15A=720W). Hope this helps. Thanks!
@fredricktroy1933
4 жыл бұрын
DIY Potentials: Projects & Ideas yes. Thank you
@jones8732
2 жыл бұрын
@@diypotentials Isn't it possible to connect a 48V, 30Amp battery? Because the controller handles it down to 15Amp anyway, right?
@marcmihelich971
2 жыл бұрын
Does the controller step down the voltage for the "on off switch" or do you need a toggle switch that matches that batteries voltage?
@diypotentials
2 жыл бұрын
The controller is rated for 48v. For the throttle switch, the controller will allow a small amount of voltage to do its job. Thanks!
@20ISH-TRUCKDRIVER
2 жыл бұрын
Very nice video
@diypotentials
2 жыл бұрын
Thank you!
@madmanau8730
7 ай бұрын
Can you provide a link for that bus block or terminal block you used? I can only find ones that distribute across all the cables not just the two terminals connected end-to-end.
@diypotentials
7 ай бұрын
Sorry for the late response. Here is the link for a similar one. amzn.to/4bVWYWK. Thanks for watching.
@dhruvayerabati6046
2 жыл бұрын
I was wondering what were the big alligator clips coming from the battery and connecting to the speed controller. I am thinking of doing a similar project and this part I need
@diypotentials
2 жыл бұрын
Those were 12 AWG wires with ring terminal connectors and alligator clips. You can find them on Amazon or ebay. You can also purchase the parts separately and put them together. Here is a link just for example. amzn.to/3BRqj3z. I hope this helps. Thanks!
@dhruvayerabati6046
2 жыл бұрын
@@diypotentials Thanks
@OnerZiur-xy1my
22 күн бұрын
Hello, what do I do if my controller doesn't have an ignition switch wire? Please and thank you
@AakashChalla
11 ай бұрын
Do every controller has same type of connetions?
@johnhenry2102
2 жыл бұрын
Thank you for the details video, but how do you mount the hall sensor, my package actually has the hall sensor separate, where do I put this sensor onto the bike?
@diypotentials
2 жыл бұрын
Hello, my understanding is that the hall sensors should be already installed in the BLDC motor. I recommend reaching out to the seller on this matter… Thanks!
@jeroenberendsen3632
2 жыл бұрын
It could be a hall sensor to mount ob your fork. Then you place a little magnet on your wheel. that setup is used for a speedometer it is seperate from te workings of the motor
@mischiefallday
2 жыл бұрын
Thank you !!
@nathanrucker4987
2 жыл бұрын
Thank you for the video. I can’t find a diagram on this controller and this is a huge help. I am trying to figure out what the remaining 4 sets of wires are for that you didn’t cover. Do you know what the black plug with the red, blue, and black wire is for. Is that peddle assist? I took the controller apart to see if the board had any clues on it. The wires were labeled as Red=+5V, Black=TX, and Blue=RX. Are the orange and black wires going into the female 3 pin plug the low brake wires? The circuit is labeled BKL on orange and GND on black. Are the grey and black wires going into the two pin plug the switching wires for forward and reverse? Grey is labeled BACK and Black is GND. Is the purple wire an battery voltage indicator wire? It is labeled XC Thank you in advance for your help.
@diypotentials
2 жыл бұрын
Hello, the black plug with the red, blue, and black wire is peddle assist. The black and orange plug is for Brake. The gray and black plug is for reverse. You are correct. The purple wire is the speedometer. Thanks!
@nathanrucker4987
2 жыл бұрын
@@diypotentials thank you very much!
@iziqjojuklar359
5 ай бұрын
How do we get current, voltage, speed and heat values from the motor controller
@oneanon
Жыл бұрын
my scooter has potentiometer and hall effect throttle what controler should I us
@sherwinsarmiento3970
2 ай бұрын
Can my 36V throttle work on a 48-volt controller for an e-bike?
@fil21fil
2 жыл бұрын
Amazing Video! how do you charge your 4x12 volt battery ? do you use a proper 48 volt charger or do you charge each battery singularly? thanks Man🙏
@diypotentials
2 жыл бұрын
Thanks for the nice words. I charge them individually, with a 12v charger. How to Charge a Battery--lead acid and lithium-ion batteries (2021) kzitem.info/news/bejne/oqCql3migqlphJw
@toydroneagrishots
2 жыл бұрын
Very few Gems like you know the internals of how it works.
@diypotentials
2 жыл бұрын
I appreciate the kind words. Thanks so much!
@trewatkins530
3 жыл бұрын
One question the blue wire off the throttle goes to any power source other than the battery right im work with different controller for a brushed set up and as this throttle is universal i need to now figure the blue wire as b4 it was blue and yellow
@diypotentials
3 жыл бұрын
That is the ignition wire to be connected to the controller.
@bertarichetaphotogra
3 жыл бұрын
What the rating for your BLDC motor? What is its RPM?
@diypotentials
3 жыл бұрын
The RPM is rated at 2800RPM. With no load, it is rated at 3100RPM. You can search this phrase on ebay for more info. 750W 48V Electric GoKart Tricycle Cart Brushless Motor Gear Reduction w/ Control. Thanks!
@shadow_7362
2 жыл бұрын
im new to all of this and bought my own stuff what is the thing that he is connecting to called at 8:45
@diypotentials
2 жыл бұрын
It is called the terminal block. Thanks!
@shafiullahislam6270
2 жыл бұрын
Sir, how many kilometers will a 3 wheeler van rickshaw run with this small battery
@diypotentials
2 жыл бұрын
So sorry. I don’t know the answer to your question. Thank you.
@shafiullahislam6270
2 жыл бұрын
@@diypotentials I want to explain to you how long this DLDC motor can run with this small battery
@atokwamenasagoe2725
Жыл бұрын
Please I want to know how to connect it to move in both forward and reverse direction...Thank you
@diypotentials
Жыл бұрын
The terminal with the black and gray wires is for reverse..
@nitaitv9365
3 жыл бұрын
So the lcd screen or screen does not show the speed but shows the volts?
@enyeazuvictor7798
Жыл бұрын
can 12v12ah acid lead battery work on 1000w bdlc motor
@diypotentials
Жыл бұрын
Lead acid batteries will work on bldc motors, but they have to meet the motor’s voltage requirement. For example, if the motor is rated for 48v, then you have to add 3 more 12v batteries to the circuit. Watch my video on how to connect batteries in series…How to Wire Batteries in Series and Parallel for Beginners! kzitem.info/news/bejne/uWyusqGrpGmml4I
@lucaspennato5616
Жыл бұрын
Hi, please, can you tell me what the blue/black/red connector and the dark (single wire) connector are for? I've the same controller but I don't know what they are for. THANKS!
@diypotentials
Жыл бұрын
The blue/black/red connector is for the pedal assist and the dark single wire is for the speed meter. Also, I just added the wiring info in the description. Thanks and good luck on your project!
@phatxboixdavid
3 жыл бұрын
Hey can you just use a 12 car battery for this 1000w motor?
@diypotentials
3 жыл бұрын
It depends on the motor’s rated voltage requirement. If the motor is rated at 48V for example, you will need more than one 12 V batteries.
@Dkrpan59
2 ай бұрын
How do you connect a display on the bldc
@phoenixcreations94
Жыл бұрын
Great, but i have a question, can this exact same motor work remotely ???
@diypotentials
Жыл бұрын
That is beyond my knowledge…sorry. Thanks for asking…
@pathumdanthanarayana9740
Жыл бұрын
Hi there! Thank you for your great explanation! I have one question. Would the 4x 12V batteries connected in parallel be enough to power, for example, a small buggy? Or would powering something like this require more power? Thanks.
@diypotentials
Жыл бұрын
It depends on the power requirement of the buggy. If the buggy is rated for 12v, then the answer is yes. Connecting the batteries in parallel will not increase the voltage level. If the buggy is rated for 48v for example, you have to connect the 4 12v batteries in series to get the 48v needed. I hope this helps!
@pathumdanthanarayana9740
Жыл бұрын
@@diypotentials Thank you! Another question I had was, would 48V be a high enough voltage to power a 4-wheeled small vehicle like a golf cart for example? I assume 48V is plenty to produce high speeds for a bike since it is low weight, but would 48V be sufficient for achieving high speeds for a heavier vehicle like a golf cart or would a higher voltage need to be used? Once again, thank you so much!
@diypotentials
Жыл бұрын
@@pathumdanthanarayana9740 It depends on the golf cart's specific voltage requirement. If it is rated for 48v then you can power it with 48v. If it is rate for 36V for example, then 48v would be to much for the engine to handle. Over time you can damage the engine. The heavier the vehicle, the more energy it will use, which means that it will draw more amps out of the batteries to meet the weight and speed needed.
@pathumdanthanarayana9740
Жыл бұрын
@@diypotentials Makes sense, thank you for your explanation :)
@DyLemmaOG
2 жыл бұрын
Hey man, what if my controller doesn't have a red electric switch wire for the blue on the voltage throttle to go to?
@diypotentials
2 жыл бұрын
It might have separate terminal for the throttle. Hopefully your controller comes with a diagram. Best wishes.
@adityabhaskara581
3 жыл бұрын
Hi I saw one cable with the black pin. I have the same pin and could not get information on that, could you please tell me what that is? Thank you.
@diypotentials
3 жыл бұрын
Can you give me the time it appears on the video?
@monsteroriginal
3 жыл бұрын
72v 35AH motor and controller can you make that vid?
@diypotentials
3 жыл бұрын
Thanks for the suggestion...I don't have the 72v motor at the moment. Maybe in the future...
@MrSoto92
6 ай бұрын
what is the total amperage being supplied? Is it 28A?
@crustytoenail1110
2 жыл бұрын
I'm thinking of building an E-bike with a 48volt 2000watt permenant magnet motor. It doesn't have hall sensors. Any downfalls with my idea?
@diypotentials
2 жыл бұрын
Check out part I & II of my ebike videos…Powerful Electric Bike Conversion Part II--Lithium-ion Battery Power Boost Upgrade kzitem.info/news/bejne/xGyPzYKHoGWHgG0
@DevasKarpDevas5000
Жыл бұрын
Hey, I am looking to use this type of Motor controller with a microcontroller, so I am having trouble finding out the correct connections. I saw your other tutorial with the small motor driver and there are 4 digital pins, Z/F, VR, Signal and EL. So as far as I know, the equivalent of the VR would be the throttle cable, but aside from that I am kind of lost, as the small motor driver has a Signal pin which I've seen is for sensor feedback, but the only cables related to this are the three hall cables, so I think an equivalent to this would be an external encoder. Now, the Z/F pin stands for direction of the motor, and EL stands for Start/Stop, so I would appreciate if you could provide me some guidance on which cables from this motor driver would be equivalent to be connected to a microcontroller, as I can't seem to find a suitable schematic or datasheet of the motor driver.
@cbrwrx
6 ай бұрын
Did you ever figure this out?
@wessley4606
3 жыл бұрын
Can you connect this to a brushed motor?
@diypotentials
3 жыл бұрын
No. You can purchase a controller for a brushed motor...check out my video on e-bike install. I used a controller for a brushed motor. Thanks!
@titinegruta9532
Жыл бұрын
Super...super video
@diypotentials
Жыл бұрын
Thank you!
@aniekanben5696
2 жыл бұрын
Please how do I get the complete kit and how much does it cost?? Thanks for your anticipated reply
@diypotentials
2 жыл бұрын
Hello, the links to the items are below the video description. Thanks and good luck on your projects.
@simonaskubilius3732
2 жыл бұрын
Hi how fast its? its got onli 600rps?do its powerful to use on off road buggy? Thanks
@yologamer5907
Жыл бұрын
same question, same project
@Steve1979a
Жыл бұрын
Hi, what would the Ah be of the battery setup and what’s the maximum discharge ?
@diypotentials
Жыл бұрын
The battery pack is 7ah. I would discharge it up to 7A only. That would be 336W. I recommend having a higher AH battery pack for a real application. Mine is just for demonstration with no load…
@RajuAhmed-ur1kp
7 ай бұрын
That 4 batteries how long can run the motor?
@NewMicroElectronics-yv1ek
Жыл бұрын
Very good 😂
@user-bc6gd9tc8m
3 жыл бұрын
Can you install this on vehicle not a bike also how fast would it go and do you now any bdcl motors which can be installed in a heavier vehicle
@diypotentials
3 жыл бұрын
A go kart, but not on a vehicle. The motor is not powerful enough for a vehicle. You might visit evwest.com for possible dc motors for vehicle conversion. Thanks!
@alexvillamil6589
6 ай бұрын
Hi. I have one of these and for some reason with all the connections properly. The brittle response is not working properly. I also have an issue where everything is connected properly but the bike started to go in reverse randomly. Please help!
@76o_1
6 ай бұрын
I got one of these too but I’m having trouble having to go not sure what it hs
@TheAmish111
3 жыл бұрын
Hi I had a question. Does it matter what awg wire we use for the battery connections? Do you mind sending a link to the wires you used? I have a similar setup but my kit came without battery wires. I have a 48V 33A controller and I wanted to get the most out of it so I was going to use 4 12v 30A batteries. Now I just need to know which wires to purchase
@diypotentials
3 жыл бұрын
Hello, you won’t be drawing 30A at a time. I recommend a 12 awg wire. Here is the wire current chart. If you think you will be drawing more amps, refer to the chart to the right rating for your project. Thanks! www.solaris-shop.com/content/American%20Wire%20Gauge%20Conductor%20Size%20Table.pdf
@mirzagee8191
2 жыл бұрын
Great video bro please help me
@richardlough5133
3 жыл бұрын
I have a 3000 watt 72 volt motor and im trying to use the same throttle you have. There's red, black, yellow, blue, and green coming from the twist throttle and the controller the following: it has a orange and a red w/white stripe for the electric lock and for the throttle there's black red and grey. Can you please please help me 🆘 ...
@diypotentials
3 жыл бұрын
Hi Richard, if I were to make the connection, I would connect the grey wire of the controller throttle plug to the green wire of bike's throttle plug. The red and black wires from both plugs should match. For the switch, since red wire w/white stripe is often associated with positive, I would align it with the yellow wire of the switch plug first. If that doesn't work, align the yellow wire with the orange and connect the blue to the red wire with white stripe. When you connect the wires, make sure the switch is on the OFF position. Good luck with your project. Thanks!
@abdullahyousef3596
Жыл бұрын
I can't find the switch wire on the motor controller, can you help me please
@danieldougan8550
3 жыл бұрын
So is the DC brushless motor or bldc motor actually a three-phase AC motor?
@diypotentials
3 жыл бұрын
The bldc motor is a direct current (dc) motor. AC motors run on alternating current (ac). So a bldc motor is not an ac motor. Both ac and dc motors can have multiple phases. Thanks 😊!
@guruprasadhr4253
Жыл бұрын
Super sir
@diypotentials
Жыл бұрын
Thanks!
@vahagnmelikyan2906
2 жыл бұрын
Will this motor work backward? I mean rotating shaft to charge the battery
@diypotentials
2 жыл бұрын
It can work as a generator. But it will produce AC voltages. You will need to convert AC to DC to charge the battery and regulate the voltage level. Thanks!
Пікірлер: 481