@@teampsi6771 hi , i tried to controll my motor with L298N and arduino nano , but my motor was not running . why it happened cause i checked the pins and program was also correct according with pin . but it doesn't work Can you help me please
@nitinsampathi
2 жыл бұрын
@@teampsi6771 Yes, the effort put into this video from the editing to the graphics is amazing
@Ripsticker45
5 жыл бұрын
he didn't put the code in so I did. //CODE: int In1 = 7; int In2 = 8; int ENA = 5; int SPEED = 210; void setup(){ pinMode(In1,OUTPUT); pinMode(In2,OUTPUT); pinMode(ENA, OUTPUT); digitalWrite(In1,HIGH); digitalWrite(In2, LOW); //ENA 255 means high speed and 0 means low speed analogWrite(ENA, SPEED); } void loop(){ }
@sanb3586
5 жыл бұрын
Hello
@sanb3586
5 жыл бұрын
Need help
@kamlarana6072
5 жыл бұрын
Thanks
@loizospapadiomidous1825
5 жыл бұрын
u saved us
@ramygabra4698
4 жыл бұрын
not all heroes wear capes! thanks bro
@jumbo999614
4 жыл бұрын
So you're saying that motor voltage must always be equal or higher than power supply. In this video, you're using 9v Battery then your motor must be 9v or more right? Also what will happen if you don't remove Vin and GND while connecting it to PC?
@lelandclayton5462
4 жыл бұрын
At lower voltages depending on the Motor it will work but turn slower and with enough current it could have more torque. However if you pump in more voltage then the Motor is rated for say 15 Volts into a 12 Volt motor it could hurt it after a while. If you pump in say 24 Volts into the 12 volt motor it will die quickly. It's just a good rule of thumb to disable the power source such as a battery when plugging it into a PC. The PC itself will pump in 5 Volts into the device in this case the Arduino and could cause issues when trying to write code to it if you have the battery plugged in and the USB. Some MCUs such as the Arduino will do a reset when it's finished getting code written to it and depending on the Power Source it won't let it reset.
@othmanmirizi6465
4 жыл бұрын
Sir im using 3-6v motor dc and 9v batteries. But my motor won't move. Is my power source too weak?
@rcarduitrix9504
4 жыл бұрын
Hey your power supply is weak make sure to use 18650 batteries and don't use 9 volt battery..... If you are having trouble using l298n motor driver then you can also use l293d ic ... You can go through my channel there i have made a separate controller to wirelessly control dc motor and servo motor... Hope this helped you :)
@everetteworley1333
4 жыл бұрын
Dude you helped me with a school project that I've been stuck on for so long. Thank you so much!!!
@thepredator1943
5 жыл бұрын
always wanted a pair of talking hands,wonderful
@GaneshHosur97
5 жыл бұрын
Concise and straight to the point explanation. Very well written description .. Hats off.. Great work!!
@harpermartin7813
2 жыл бұрын
Awesome video! It was very helpful. God bless and always remember that Jesus Christ loves you all so much! Jesus Christ is Savior and He died for you! Have a great week!
@kesavanramesh5663
5 жыл бұрын
I was trying to connect a male wire to the screw terminal {facepalm}
@reganclare5622
Жыл бұрын
Pure genius. What a clean demonstration. Thank you good sir.
@ARAcademyTamil
5 жыл бұрын
Hey man give the Arduino code???
@themiraclelab9774
3 жыл бұрын
where can i get the code
@kartikkashyap7595
7 жыл бұрын
Good work !!!!! And please upload such informative videos
@carzycults6119
4 жыл бұрын
Bro I have done the same stuff wid two 5 volt dc motors but they are not rotating can suggest me anything I powered the bridge with 9 volts dc like you sir?
@varshamahajan7285
4 жыл бұрын
How to download arduino uno programming on the laptop can you help us and fast too
@shantanusingh6699
4 жыл бұрын
4:33 Please explain the use of that 5v terminal, is it for enabling or powering Arduino? Is it 5v output or 5v input?? Also Can we use l293 with configuration?
@bigfilsing
4 жыл бұрын
as it goes to the VIN pin on the arduino its an output on the L298N
@hetshah7490
4 жыл бұрын
Bro it's for to power motor driver
@utoothheartyeight
Жыл бұрын
Out
@fourleafclovis78
3 жыл бұрын
did anyone else get: C:\Users\Admin\AppData\Local\Temp\ccuLmagZ.ltrans0.ltrans.o: In function `main': C:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino/main.cpp:46: undefined reference to `loop' collect2.exe: error: ld returned 1 exit status exit status 1 Error compiling for board Arduino Uno.
@luckshaeey
3 жыл бұрын
You used a 9v battery but connected a 12v motor. Why so?
@tinkertom3683
Жыл бұрын
I connect the the l298n to a stepper motor nema17 my DC power supply shows no current being drawn when I send a signal to move the stepper one revolution and then stops I notice it's still continuously drawing max amps and it's in CC mode an till I reset the Arduino then it goes back to normal again it's like the pins 8,9,10,11 are causing it to still run some how also after about 30mins the rc522 RFID scanner stops working any ideas what this could be?
@atabak7912
3 ай бұрын
hi. If I have a 9V 2A adapter instead of a battery, how should I transfer the power to L298N Dual H-Bridge Motor Controller ??
@ranjansarkar3620
4 жыл бұрын
I like the way he explains it! Good!
@saadatkhan2791
5 жыл бұрын
Wow! a really good video. Great explanation, great editing; the effort put in the video is exceptional.
@jaimeherrera2510
7 жыл бұрын
Thank you very much. You explain so clear.
@jeranrai645
4 жыл бұрын
7:33, is it necessary to pull out the Vin and GND connection before connecting the data cable to computer ?
@shastudents9215
5 жыл бұрын
it doesnt work for me, the motor doesnt make any sense, please help
@oskargajewski5904
4 жыл бұрын
Finally i found somebody who explained me this connection. Thank you
@amoghnivas6624
4 жыл бұрын
Sir, when i followed the same procedure as above, the motor rotated stepwise. Please help.
@hcsh36
5 жыл бұрын
Wow very clear instructions!
@manishpanchal8689
7 жыл бұрын
Nice Explanation.
@JavierRomeroo
5 жыл бұрын
Hi Team PSI, great video! Can I use part of your video (without the audio) for a quick explanation on a L298N?
@JekPorkbricks
3 жыл бұрын
Can this also work with a 9V 5A DC motor? As long as I have a power supply of 9V that also has a current of at least 5A? The only L298N that I could find has a value of 25W though, and the motor has 9*5=45W power. I don't know if that'll work.
@16.minato
6 ай бұрын
If i am using power from my latop, can i power the motor driver with arduinos 5v pin ?
@cruzo2355
4 жыл бұрын
Add some potenciometr and or switcher please. :)
@MIHAI0410
3 жыл бұрын
Hi community. I need some advice regarding H Bridge guy's. What I am looking for is just H Bridge which can change the polarity of the around 100 times per second. Must work between 5 Volt to 12 Volt. What you recommend ? Many thanks
@ayushsinha7416
4 жыл бұрын
Bro I have made a wifi control car using node mcu esp8266,l298n motor driver and a 5v battery but the motor is not moving and making beeping sound.
@febochestbox5507
3 жыл бұрын
What about sample wiring connection for 24Vpower supply to drive two 24V DCmotor, using Arduino Uno along a breadboard. Assuming Arduino Board is powered by 9V Battery, ENA and ENB enable.
@PCsolution56
11 ай бұрын
Bro my +ve wire of the 9v battery gets only light up by 5v of the driver
@berk530
4 жыл бұрын
I have 3 TB6612FNG motor driver. I am trying to connect 3 motor drivers to arduino. Which arduino should i use?
@miheerabhyankar9223
6 жыл бұрын
Please give me codings/sketch and very very nice explaining sir.
@sanjunamathews-robotechietips
4 жыл бұрын
Nice video.. I have a doubt.. I am using Ros serial for varying speed from robot operating system and I am having 12v power supply.. In that case is it safe to connect gpio pins while Arduino is connected to laptop.. ?
@emryscass7327
4 жыл бұрын
My motor spins in 'ticks'. So it spins maybe 1/8 of an inch, stops, spins an 1/8 of an inch, stops - this repeats until I power down the arduino. Why isn't it a consistent smooth spin?
@Ryuisdragon
Жыл бұрын
Could i connect two different Motor in the same motor driver using the In 3&4 and the Enb to control it, without changing the power source?
@MakersMic
4 жыл бұрын
great info that helped me out on my project!
@Msopasniful
4 жыл бұрын
Hello, can i connect 4 motors to L298N? I connected two motors to the L298N and they work normally but while I connect the third it slows down and only one motor works. I am using a 9V battery. Do they need two batteries or is it something else?
@foodies4140
4 жыл бұрын
can we connect 4 motors to the same arduino
@sukanyabharti6704
2 жыл бұрын
sir is there any extra component required like resistor or any more? or by using this much only it will work...i m little bit confused..please help
@milosp.551
Жыл бұрын
Can you connect battery on arduino and via 5v pin it delivery power to driver?
@shan_singh
4 жыл бұрын
would've been nice if you provided code in description!!
@armedcoffee6535
3 жыл бұрын
Yes
@hindolsarkar2036
6 жыл бұрын
Hey where is the source code?
@harshadpatil6622
5 жыл бұрын
I want code
@raifhanna131
3 жыл бұрын
can we use steps of any Axis"x,y,z" out of cnc controller to control the speed of a Dc motor or stepper motor while running G-Code???
@bhartiya_nagrik
3 жыл бұрын
Can I connect 5v of arudino to the 5v of motor driver? .... Please reply fast 🙏🙏🙏🙏
@mochastellar
4 жыл бұрын
Can someone explain why arduino is not plugged to the laptop? Is that enough the voltage source only from the battery?
@seanlyon2870
2 жыл бұрын
Nice video! What should I change if I use a 24 power to power a 24V motor? Thanks
@samyount2546
3 жыл бұрын
For anyone whose motor just pulses without rotating (which was happening to me) you just need to use an independent power supply for your Arduino so that the 9v battery's current doesn't get overcharged when trying to start the motor and power the Arduino at the same time.
@BongChoch
2 жыл бұрын
still not working broo can you please help
@livinglivelike
Жыл бұрын
@@BongChoch do you still need help?
@AmeyaPradhan
10 ай бұрын
How? can you explain the schematic
@tonycarboni2002
2 жыл бұрын
3:20 "screw them up". How'd he know what I was doing with this thing all day.
@DeveloperJunaid
6 жыл бұрын
Sir If We use 9v battery to 12v dc motor and if Its clip which fits the power supply terminal of arduino, then will it damage the motor?
@amartaoussi2317
4 жыл бұрын
مخرج رقم 3 لاعلاقة له بالمحرك رقم 1 ترجم وتعلم مني هههههه
@MuhammadAwais-jh2dy
Жыл бұрын
Do u have video about linear actuator with arduino
@MARK-qk5qu
4 жыл бұрын
Hi, i need the same mechanic but i need to put a rain drop sensor to trigger the motor, how will i do it, please help me.
@sahilkamble240
5 жыл бұрын
Hi my l298 motor driver ni 12 volt not supported but + supply attach to 5 volt out put it has worked but but way problem of 12 Volt is not supported
@Skyonly_22
2 жыл бұрын
Hello can i ask.. What battery that u use ?
@RMCMC_AmitNikhade
4 жыл бұрын
How can I use separate batteries for the Arduino and the motors. Please help.
@istvannejonas6246
Жыл бұрын
I am thankfull for video!
@croydon21H
4 жыл бұрын
is it not possible to attach 9v battery connected to motor driver and still use usb to upload code?
@shivamganmote3847
4 жыл бұрын
Can we use dc dc power booster instead of motor driver ?? Plz ans ...
@madridmadrid7660
Жыл бұрын
Can you do one where to add press buttons on it
@maheshgond1106
4 жыл бұрын
Why you disconnected the Arduino to motor driver Vin and Gnd connection after send the code in Arduino board
@kuldeeprane1469
3 жыл бұрын
Can I do the same thing to my Arduino nano
@abhishekbiswas9871
4 жыл бұрын
Can u make a tutorial of same setup controlled using mobile app and wifi module esp8266. Great video.
@boowonder888
7 жыл бұрын
Thanks 4 letting me know about pwm and it's sinus sign on next to the pin, that's important info!
@user-irb
3 жыл бұрын
Hi can you fix N20motor connect adurino noisy?
@caldas1798
4 жыл бұрын
my motor doesnt turn rotate i heard a sond but nothing happened Any help??
@RixtronixLAB
2 жыл бұрын
Creative video, thanks for sharing, like it :)
@sourabhgayake7015
4 жыл бұрын
Can i use it for 24V DC, 1440RPM, 5A Motor....
@zainfarooquimohammed823
2 жыл бұрын
can you post your program in comments
@harshadpatil6622
5 жыл бұрын
Plz giv code
@NagashreeKMGMEC
2 жыл бұрын
Sir can we use 1000kV motor with 5V battery
@Mememeister
7 жыл бұрын
Thank you very much. Really good video!
@jfukui_
7 ай бұрын
Obrigado, ajudou bastante!!!
@pramodkalhara3999
Ай бұрын
bro thank you very much
@theenlightenedone4738
6 жыл бұрын
Great video........Check out my ps2 controlled car I used a l298n but the motor over heats fast any advice
@gamecity7265
6 жыл бұрын
I programed a stepper motor that stop 24 time in one loop. Would you know how to turn on an led for each stop ? So 24 blink. LED on while motors stops. LED off while motor rotates. Thanx for your great help
@julienvandenbroeck4378
4 жыл бұрын
Where's your laptop? How do you get into your routine. You still have a lot to add.
@thehypothesisxplorer4449
3 жыл бұрын
I have a 3V DC motor. Can I run it with this motor drive?
@freemanfreed1581
5 жыл бұрын
we can separately give power to arduino right? connecting arduino to external power source instead of connecting the 5v from the motor driver with the arduino power pin is also possible??
@hiteshjain2640
4 жыл бұрын
Hey good work, can you review my video on Robotherapy it’s on the same topic
@jdstudios1912
2 жыл бұрын
Very helpful thank you so much, i do have a follow up question. How would one co about scaling this up to two motors?
@shayanv3337
Жыл бұрын
NEATEST DC MOTOR ARDUINO INTEGRATION VIDEO IN KZitem ,THANK YOU
@Anton-sz6ef
5 жыл бұрын
Please someone answer : can I use it for a physics project where I need a high frequency current of like 3.3V meaning low and 5V meaning high. Can I like use it by changing it really fast with the Arduino commands and create the signal I want to create ? Thank you!
@genbot7207
5 жыл бұрын
it dependes on your motor . if u use a motor that doesnt want to exceed the power limit of 3.3v ,then u can reduce the speed in the programing which will produce a less amount of power supply. so u r motor could run. but make sure u program perfectly so that ur motor reaches correct 3-3.5v .
@Anton-sz6ef
5 жыл бұрын
@@genbot7207 Noo not for a motor. I use it for an experiment with electromagnetic radiation. Basically i just send 3.3V then 5V repeatedly very very fast to create 0 and 1 and stuff like that. The thing is it might be too fast for the driver to handle. I am talking about GHz here.
@lungchuingamriammei6631
3 жыл бұрын
But sir when do we remove the power jumper cable
@sanjibsahu7519
Жыл бұрын
can you give me the code
@sreeshnar4639
Жыл бұрын
Is it possible to work without uploading code
@Ryuisdragon
Жыл бұрын
No
@mohamedameri360
6 жыл бұрын
Your tutorial is contradicting itself, first u said we have to connect 12V only for big DC motors, so I used the 5V for my small DC motor but then u also used the 5V terminal! WTF? u basically used both terminals... How are we supposed to do exactly??
@ujjwaljha2402
5 жыл бұрын
he is using 5v supply to power the arduino
@bharathbandaru8619
5 жыл бұрын
we are using 3-6v dc motor with motor cnotroller and arduino uno. can we use 9v battery supply to drive the motor. If yes, can you tell me how to conect with arduino?
@omkarkhade4602
5 жыл бұрын
yes , you can use 9v power supply for your 6v motor but dont go beyond 9v. The connections are explained in the video.
Пікірлер: 279