Thank you for the great instruction. Exactly what I was looking for. Concise and to the point.
@aaronadams385
2 жыл бұрын
It is my pleasure. I am glad you found it useful Thanks for subscribing. Have a great day.
@josesquiabro5819
10 ай бұрын
Dude you are heaven sent!!! Thank you for the videos! Explained perfectly!!!
@aaronadams385
10 ай бұрын
Glad you like them!
@hsmd4533
2 жыл бұрын
Great video, thanks for explaining this so well
@djjoeykmusic
11 ай бұрын
Great video A lot of information. Thank you so much Blessings
@aaronadams385
10 ай бұрын
You are so welcome
@Torch4Life
8 ай бұрын
Great demo Mr Adams, my problem is I need a 67.50 degree bevel.
@MrJaydub1001
3 ай бұрын
I know it's really late but a 33.50 degree bevel on the off-piece puts a 67.50 bevel on the work piece.
@jamiebond6349
Ай бұрын
helpful video.. well explained
@edmuboro4582
Жыл бұрын
Perfect for small projects. Not got a lot of power so if the wood starts to flex it stops the saw pretty easy. Use it for small tasks and you will be happy. Safety system Works great kzitem.infoUgkxjpBI8OOeUXib_iT7UomCrQ-uauwZJ62c .lose your grip on the saw it shuts off and the sheath closes over exposed saw.
@kennethmorgan8268
Жыл бұрын
So your not struggling during the cut, make sure you use your square to guide the table of your circular saw
@ivonne2587
2 жыл бұрын
The exact info I was looking for!!
@crs4600
Жыл бұрын
Newbie here, why isn't the wood secured to the table with clamps? Isn't that dangerous?
@evelynpadilla1045
2 жыл бұрын
Does every Circular saw have that thing for the 45 degrees?
@aaronadams385
2 жыл бұрын
Most of the saws that I have ever used do.
@LoveLumps7585
Жыл бұрын
Thanks for sharing 👍🏽. I will you know how it goes
@howdy4686
Жыл бұрын
Thank you!
@davidseed8911
5 ай бұрын
Think I might have unplugged before adjusting the blade angle
@mobilecommunicationsnetwor5268
Жыл бұрын
Why does the depth have to be set to all the way down?
@devoncsmith2696
10 ай бұрын
To compensate for the angle when you cut through the timber.
@89TNash
Жыл бұрын
How to cut that 45 and be straight? I cut some wood today and seemed a little off
@devoncsmith2696
10 ай бұрын
Takes practice. The more you do it, the better you get at it. When you join two or more angled cuts together, you are better using a drop saw, because 9 times out of 10, one angle might be off a couple of mms than the next one, and so when it comes to joining the angled cuts together, your angled cut might end up having being too short creating a gap.
@jameslabs1
2 жыл бұрын
Thanks
@aaronadams385
Жыл бұрын
No problem
@2pacnasgame
11 ай бұрын
I did that my blade did not go all the way threw
@ScottFranklin-of3nz
Жыл бұрын
Here in oklahoma Vocational school teachers were not mentioned by board of education pay or any teachers awards may 2023
Пікірлер: 29