Would really love to see more 3D printing/ EDM stuff on this channel. It's unusual and not something we see very often compared to normal milling/ turning etc
@trevorgoforth8963
2 жыл бұрын
You're in luck, now that our EDM and 3D printing departments are set up, we will be busting out more content like this!
@gooblio
2 жыл бұрын
😎, get me a hacksaw. Done 😃
@thomasbarlow4223
2 жыл бұрын
Yeah now find me a hacksaw blade that's 0.0010 of an inch thick
@alexchandras5618
2 жыл бұрын
Give me chopsaw. Done 😎
@JohnBlaze505
2 жыл бұрын
Super precise
@gooblio
2 жыл бұрын
@@thomasbarlow4223 The wire is . 010" not . 001" and why can't it be . 032" the part is only being cut to look inside. There's no specification for the cut other than being straight with a decent finish. Band saw and a belt sander. Done and you haven't finished a fixture yet
@gooblio
2 жыл бұрын
@@alexchandras5618 Even better, I use to use one for inspecting the heat treatment on a part. Cut it in half with the chop saw and polish it on the belt sander to check the depth of the case hardening.
@Stasiek_Zabojca
2 жыл бұрын
That moment at 8:41 beautifully shows one of the most challenges in wire EDM. You can't just cut huge chunk of material. Some parts are very challenging with internal stresses, parts will move slightly when cutting and removing material. You have to be smart with bridges you leave to cut the part off. On a machine with micron and smaller capabilities, this may be huge problem for some features. For this part in video, I think that it would be better to cut from side of the mounting plate to the right. Not that it matters, really, it was just to show the inside of the 3D printed part :)
@chrisdilz
2 жыл бұрын
That programme he showed did not finish that part, you could see how much the part moved. The 2nd and 3rd cut wouldn't of even done anything. He would of ran a second programme to clear up that face once it had moved. This happens all the time in unstable material. Something harder and more stable wouldn't of moved as much.
@Stasiek_Zabojca
2 жыл бұрын
@@chrisdilz It's obvious it did not clean up anything as rough pass leaves max a few hundredths of a millimeter to remove in skim pass/passes. It's not just the material, it's about part geometry, how it was hold to the plate. Maybe if it was annealed it could help a little bit, but I don't think it would be much. Also, in the industry you can't just anneal something or make it from different material. You have to find a solution, if there is any.
@Stasiek_Zabojca
Жыл бұрын
@@spelunking4444 Well, it's not really anything that you measure before last pass. You would rather cut a piece of that material (that will be removed anyway) before and measure this and then adjust if needed and proceed to real cutting. Sometimes I just knew what dimensions will be, because it's very repeatable process. From data book, depending on your desired amount of passes, for example for 50mm heigh steel piece: •One roughing pass and one finishing wold be around 0,03mm for finishing pass. •One roughing and three finishing would leave just 0,001mm for last finishing pass.
@ZURAD
2 жыл бұрын
EDM needs a better description than what it was given, so here goes: DI water does NOT allow current to pass through as he said, it specifically is a "dielectric", meaning it resists flow of current. What happens in EDM is that the high voltage breaks down the water in the electrode gap once the "dielectric constant" is exceeded. That is, once the voltage exceeds what the water can resist, an ablative arc forms and burns away a little bit of the target material as well as a much smaller bit of the tool. The accuracy of EDM comes from the short length and duration of said ablative arc. In modern wire EDM, there are hundreds of thousands of arc generated PER SECOND. They only reach a few thou, if that, away from the tool. Very neat stuff overall.
@happygilmore2100
2 жыл бұрын
I know what EDM is and vaguely how it works but thank you for taking your time to explain the process.
@barrysetzer
2 жыл бұрын
Super cool internal geometry! I couldve machined that
@Bawbag0110
2 жыл бұрын
Then give it a big ol kids afterwards 🤣
@Michaelsloncehammr
2 жыл бұрын
Those holes twist drills can’t make that type hole.
@christhut8140
2 жыл бұрын
*couldn't have
@KevinJones-pj8kx
2 жыл бұрын
How much wire was consumed in the process of this cut? That spool was turning at a pretty good pace during the video.
@somethingelse4424
2 жыл бұрын
I was under the impression that the wire was not consumed, but I'm not very familiar with the process. I thought the wire only takes minimal damage and was rewound as the machine goes... Kind of like a bandsaw?
@StevenHeins
2 жыл бұрын
@@somethingelse4424 The wire is actually also eroded by the cutting action, so it has to be fed off of the new reel at the top to a waste bin that is usually at the back of the machine.
@somethingelse4424
2 жыл бұрын
@@StevenHeins I see, so I assume you adjust the wire feed so that it is as slow as possible without being entirely eroded to the point of breaking? I guess you recover the brass, but I doubt the scrap value does much to offset the cost of new wire.
@StevenHeins
2 жыл бұрын
@@somethingelse4424 yes, it's a balancing act. There are servicing companies that are happy to take it, though it can get contaminated by the swarf from the cut
@HenrikSkov-DK
2 жыл бұрын
I do this every day, just on an older machine. And I love it. It's mega cool to see a newer machine and with an employee who is good at explaining what he's doing. And I love the 3D printed part. Cool 😀
@scottylam523
2 жыл бұрын
I did exactly this at the last company I was at. Cleaning the trapped metal powder out of the edm was always a nightmare after a just a few parts
@fishsticks88
2 жыл бұрын
Same hated that crap..
@chrisdilz
2 жыл бұрын
I dont get it? I just hose down the tank every day and you just change the filters and swap the deionizing resin after a set amount of hours. Not exactly difficult?
@BenWilson24
2 жыл бұрын
Sounds like the part wasn't properly designed for AM if there was still powder trapped inside
@berntinulkshredder
2 жыл бұрын
Love EDM and wire cut things, cutting almost daily. Love when the spark is clean and yeah when it gets it right. How long did that part took you to part it off? Curious of how fast latest things are.
@EricBrummer
2 жыл бұрын
Yea no mention of cut time is a glaring omission when discussing this kind of technology especially for the many viewers that have no idea how long EDM can take.
@ricardo-iw9sq
2 жыл бұрын
Bad flushing 😂😆🤣 mines open flushing ie none submerged and when i have jobs where i have to have the Z high and cutting through cavities I get loads of dry spark issues, usually what titans do in machining blows my mind and have no experience with fancy cnc I do with edm wire 20+ years, with that part opening up with the stresses you should have cut from your jig to the end and leave a tab and then cut the base, I do stuff like this cutting into sections so they can be 3d scanned to make sure they are like what a cad model is supposed to be and to make sure the 3d printer is doing the features needed, It blows my mind when wire cutting a part open to find whats inside and the incredible detail. 👍👍👍
@Nickle314
2 жыл бұрын
Interesting that when you cut it in half, it sprung open. That must mean there is some stress in the part.
@Stasiek_Zabojca
2 жыл бұрын
There is always some internal stress in metal. It's the most noticeable in long and thin parts, even when milling. It's especially true for hardened steels, which have a lot of internal stresses.
@TheTechAdmin
Жыл бұрын
6:49 It's ironic that the "dry run" is simulated with a wire made of water.
@Robert-in4he
2 жыл бұрын
Good video. Could you guys do a solidworks or fusion tutorial on how to model that part? I gather the pipes would be a profile swept along a spiral/helix. How about the ribbing on the outside? This part is complex and it would be a great asset to us all if you could teach us how to model it. If so, it would be greatly appreciated. Have a good day.
@jenbadabam8801
2 жыл бұрын
1:55 e d g i n g
@rizzler05
2 жыл бұрын
did a good job explaining your locations. faster way was to center find the end off part. move to center of part and cut +X.
@465maltbie
2 жыл бұрын
Interesting how you see the stress relieved on that part once it was cut through. Charles
@vn-dc3hv
2 жыл бұрын
I was just thinking the same. I wonder if they did any kind of stress relief HT for the part before EDM.
@turbo2ltr
2 жыл бұрын
Yeah exactly. beat me to it.
@karlmckinnell8652
2 жыл бұрын
EDM a part with to different geometric shapes on either end. When I was an apprentice in the early 90’s our shop EDM’d a testing clamp (heat treated) that utilized the block and cut out for destructive pull testing. It varied in shape and size one end to the other and with the slug split (EDM also) so when installed into the test rig the more pull force applied the greater the clamping pressure. I can’t recall the tolerance from end to end or angles involved but I do remember being amazed that such profiles could be cut to such accuracy. Thanks I’ll be looking forward to seeing what you have next.
@roderos
2 жыл бұрын
Could you try to improve the surface finish of the tube insides by running fine abrasives trough it like sandblasting? Maybe print tollerances to account for the material you need to remove
@kochuev84
2 жыл бұрын
Это просто охрененно!
@thecosmicknowingknowing3099
2 жыл бұрын
Great Grand Rising Cosmic Star's TEAM TITAN ARE THE MOST PEOPLE...DOING THE MOST A TERM THE YOUNG FOLK USE Titan University can get My DoeRaeMeeeee, truth My child Will be on deck soon. Wow you guy's and girl's ROCK. NOW FOR MORE KNOWLEDGE. PEACE PEACE TITAN. BOOOOM
@Kingdingaling75
2 жыл бұрын
I know very little about CNC machines but I cannot understand why calibrating the CNC machine is performed physically/mechanically instead of using lasers. 🤷🏻♂️
@seventimesman4034
2 жыл бұрын
Wire edm's are money..Wish we had one in my current shop. Miss it.. Massaging the burn parameters helped me overcome poor flush conditions.
@walterhiegel3020
2 жыл бұрын
This is the kind of tech that changes everything. Never seen anything like it!
@Nobody-Nowhere
2 жыл бұрын
Goddamn these american measuring units, 3 times of human hair.
@mattjohns3394
2 жыл бұрын
Anything to avoid metric.
@xasanbatista3334
2 жыл бұрын
AGIE is better and much easier
@wd8557
2 жыл бұрын
Congratulation's to the guy who jumped into that unit a filmed everything under water, didn't even see him one time, fantastic work.
@WXSTANG
Жыл бұрын
Just think that all this 3D printed stuff happened from a couple of us crazy dudes who took some old dot matrix printers and added extruder heads. Wild.
@xyzconceptsYT
2 жыл бұрын
Love EDM. Also the machining as well.
@alainpacheco2608
2 жыл бұрын
I have been working at edm for 5 years, they are incredible machines
@rhindy6846
2 жыл бұрын
How did u get into it if you don't mind me asking?
@chrisdilz
2 жыл бұрын
@@rhindy6846 I'm not the guy you asked the question, but heres how i got into it... I went for a CNC milling job but was told unfortunately one person came out on top... 3 weeks later they called me back and asked if i was interested in WEDM instead. I now run 4 WEDM machines, a EDM drill and a EDM Sinker. Ive just put a 6th axis into one of the WEDM machines too. I find it fascinating and the parts I make are so much more interesting than what I would of been milling.
@rhindy6846
2 жыл бұрын
@@chrisdilz thanks for the reply appreciate it. Where I live it seems to be you get put on a machine and that's your machine. I can work all the CNC lathes milling machines and borers but they have just kept me on the milling machine. Don't get me wrong I like milling the beat but would love to know how to work this EDM machines
@chrisdilz
2 жыл бұрын
@@rhindy6846 does your work have them? Tell them your interested! Shadow whoever ops them, cover their holidays? My work would be screwed if I left nobody else can run them, or use the cad software I use with them. One of the best things about Edm Is I no longer have to ask my wife to get metal splinters out my feet 😂
@Humbulla93
2 жыл бұрын
@@chrisdilz i hav a question, does the wire get "used up" or could you reuse the brass wire indefinitely?
@tian1701
2 жыл бұрын
Menurut buku jav kakek Sugiono Halaman 6 - 9 Tertulis: "Barang siapa yang memposting hal hal porno tanpa menyertakan link,akan di kenakan hukuman kebiri atau denda senilai 70(tujuh puluh) perempuan muda" Bahkan pepatah pernah berkata "Berat sama dipikul, ringan sama dijinjing,bila foto tiada judul,minimal link lah anjing"
@brahtrumpwonbigly7309
2 жыл бұрын
I feel the deionized water and how the machine cuts could have used a better explenation. He described distilled water, but didn't explain how the machine cuts or why it needs submerged in deionized fluid specifically. Just a thought.
@brandonr4965
2 жыл бұрын
The deionized water acts similar to the insulation on a copper wire, it focuses the electricity to only the wire and the part, thus making it possible to generate a spark powerful enough to cut through the metal while at the same time preventing that spark from creating an arc to the metal panels of the machine. If you touched the wire outside of that water while the machine was running, it would have enough energy to kill you. I hope that explains the process.
@readthetype
2 жыл бұрын
Why the eff are you making me feel like I’m having a seizure, in a night club, whilst on ecstasy, in order to watch a video about 3D printing? Absolutely *none* of that lines up. And for “more information,” your web site sucks. Fewer acronyms, more plain language please. Fire your marketing team. Also, never say _“whilst.”_
@spplS.
2 жыл бұрын
5:45 "Verein Deutscher Ingenieure" that just doesn't make sense at all. Translated it's something like "club of German engineers". So when you put in "17", do you have 17 clubs of German engineers then?
@fg786
2 жыл бұрын
On the machine there are stickers. Wear gloves, eye protection, safety boots and wash your hands, danger of falling in, no pacemakers allowed. "I can actually put my hand in it no problem." The part gapes apart. Is that due to residual stresses from 3D printing or due to uneven clamping on the part holder?
@hithere3609
2 жыл бұрын
#VeryCool! #ThankYou! for keeping it positive. This video shows what is possible if we all try to get the best grades in school. Please in the next video give a shout out for all those who are coming up. By shooting out "YA HOOOOO!"
@ibonjaio8345
2 жыл бұрын
Really nice video!! Waiting more wire edm apps!! And if you need some tips foe ONA AV35 I could help you. Congrats!
@toroidwinder2089
2 жыл бұрын
The laser process obviously built in internal stresses. The software manu needs to add control over where the laser first and last melts. For example, melt on one side first, and subsequent passes will freeze and shrink, adding to stresses. If you were lasering a tube for example, and spiralled from the inside out, the outer runs will freeze and try to pull the work outward. If you can convince the software to start at center of tube thickness, and work outward in both radial directions, I believe the stresses would not conspire. I would be happy to brainstorm this issue with you guys, the machine builders, and the software designers...I work all three topics. You are awesome..well, actually, badass!! John
@alexportiiii6414
Жыл бұрын
Polish it internally with extrude hone. High abrasive clay pumped at high force. Freaking amazing. Nice job!
@Th4thWiseman
2 жыл бұрын
Nice 3D print,nice video using an EDM in a very basic straight cut, professional presentation! Good viewing example👍
@leviathanops4524
2 жыл бұрын
I like the video, and i mean this constructively, but holy fuck the intro music is so LOUD, and the voice is so chill and quiet. Audio needs some normalization but this video was super cool, 3d printed metal is so wild to think about how it can change manufacturing forever
@kidjetrecon7153
5 ай бұрын
I thought I was big shit flame cutting 2” steel , not so much. X&Y will never change.Amazing, water jet cutting was just entertaining my trade, this is way more interesting.
@solidkreate5007
2 жыл бұрын
You guys should machine an SST cube with an 8Ra finish and EDM a snake curve in it an watch everyone's heads explode when you move it apart.
@AUS5113
2 жыл бұрын
That was totally sick to watch. Love the technology that is being invented these days. Seeing this video makes me wish I had my own machine shop where I could just run wild trying to invent things.
@saschafunk1644
2 жыл бұрын
All the sand cores in our foundry in Germany have been produced with 3D Printing Technology for 25 years.
@carbonfibercreationswashin7213
2 жыл бұрын
Very cool and amazing. This type of part may not even be possible to make without 3D printing or hundreds of man hours of hands on fabrication. Instead the 3D printer did most of the work besides the set up and cad
@OneCupOfCoffee204
2 жыл бұрын
What is the purpose of the ridiculous music? If I want to listen to music, I wouldn't be looking at machining videos!!
@josefk455
2 жыл бұрын
2 finish passes. Don’t think so. Part opens up quite a bit (what I would also expect) @8:42
@Nickle314
2 жыл бұрын
I've just commented on the same. That must mean there is some internal stresses in the part. Question is would a heat treat remove the stresses?
@josefk455
2 жыл бұрын
@@Nickle314 never cut printed parts myself but a bit of movement is normal to me with separating cuts. This looks quite a bit more open than I’m used to it with my parts.
@ABaumstumpf
2 жыл бұрын
The claim that you are not shocked cause of the deionised water is quit frankly false and dangerous. The water is initially deiosnised - sure - but that just increases its resistance, not make it not conduct electricity. On the other hand, as soon as the process starts, the water becomes a lot more conductive. The reason you do not get shocked is cause the designers of the machine were not such colossal morons and took the safety of idiots into consideration and galvanically isolated the powersupply (and the wire is directly next to the big lump of metal that closes the loop).
@Blake-gh8xl
2 жыл бұрын
Whoever produces this channel needs to be fired. This is youtube, not the history Channel/east coast chopper pickers. Interesting content but can't do it.
@tomiem1386
Жыл бұрын
I can't wait for this technology to become more affordable and avaliable to consumers and hobbiests. Imagine all the things people could create
@HermanLeung909
2 жыл бұрын
The EDM doesn't look much different to the Sodick EDM I used 40 years ago.
@andrewut7ya511
2 жыл бұрын
Im not a machinist, i just like precision tools and work. Can someone tell me why this part was cut? Was this just for a demo or a test of some kind?
@out_on_bail
2 жыл бұрын
Puts hand in water that was deionised but actually isn’t cause has the shavings of metal from part.
@goinhot9133
2 жыл бұрын
By the time your setup & ready to cut, my cordless recip saw is waiting for next part 🥱😉
@amirfmaster2515
Жыл бұрын
"Puts hand in water" Don't try this at home well...i don't have an Ona at home so never mind...
@Hitagara
Ай бұрын
Oh, these fantastic cutting technologies that come from the Soviet Union...
@darchojandreoski6015
2 жыл бұрын
Die Autobahn Richtung von Kicevo Stadt aus Richtung Stadt Tetovo und Stadt Gostivar ist jetzt gesperrt Die ersten Wohnhäuser dort wurden zerschossen von R.MKD ARMIJA PANZER - Die Stadt Skopje Autobahn Kreuz wird Richtung Stadt Gostivar und Stadt Tetovo gesperrt heute Nacht Zaiziki machen wir diese 2 Städte.
@harambo88
2 жыл бұрын
my friend was allowed to hear some of his music while i am on toilet. he likes electronic dance music, i love the algo, he is so sour.
@abundantharmony
2 жыл бұрын
Wow.. all of that info we will never use just to squeeze out 10 mins. 07:00 is when he cuts the thing.
@randywl8925
2 жыл бұрын
As the wire is cutting, it clouds up the water. Would that make the water conductive again so that if you stuck your hand in there you'd get fried?
@geoff0brn
2 жыл бұрын
Not fried but a little shock near the cut.
@iBlue0riginal
Жыл бұрын
8:22 Nice, putting your hand into the hexavalent chromium soup.
@chokalocpurple9243
2 жыл бұрын
It’s funny seeing the people who don’t get the importance of this getting butt hurt in the comments for no reason
@KenFullman
Жыл бұрын
I'd be interested to know how much material is removed in this first pass.
@tloekke77
2 жыл бұрын
Cool, when printing tube like that is there at way to polish them inside to get a clean surface
@michaelmorrison4201
2 жыл бұрын
Looks like you guys have some pretty neat toys. The joker would be proud
@RichardBaran
2 жыл бұрын
7:02 save you all some time. Did they explain why you do this instead of a water jet?
@martyb3783
2 жыл бұрын
I am shocked that you still use inches as a measurement unit. Great video otherwise.
@Rareenergy
2 жыл бұрын
Why not auto sense part with an xbox camera and a "slice in half" button.
@nakabamiTV
Жыл бұрын
why is finding the position so complicated, why cannot it be done with optical position?
@JusticeLogic819
2 жыл бұрын
The moment you started cutting that piece you had ions in the water,immediate contamination.
@haas324
2 жыл бұрын
Trumpf machines a great when they are running properly. Good luck with service though. Every time I have had to deal with Trumpf service. It was a nightmare.
@BenWilson24
2 жыл бұрын
Yup, had the same experience...
@dylannorris1836
2 жыл бұрын
Are 3d printed parts structurally weaker then machined parts?
@goatsinker347
2 жыл бұрын
That machine looks very affordable 😆😆
@Sphyxx
2 жыл бұрын
I wish I had money for cool af machinery to make all kinds of stuff
@highlandermachineworks5795
2 жыл бұрын
Anyone catch the mistake about 1/2 way through?
@dontask8979
2 жыл бұрын
Does the wire get pulled through and more or less get replaced as it goes?
@kiloton1920
2 жыл бұрын
I am guessing that part is made to mix and emulsify oil and water
@Samsgarden
2 жыл бұрын
Impossible, yet you cut it. Hmmm. Hyperbole much?
@DAVE_WHITE
2 жыл бұрын
you picked brass 0.25 not 0.10 at 5:39 in
@xyzconceptsYT
2 жыл бұрын
He picked the metric equivalent being 0.25mm = 0.010" (close enough 😉)
@bloodsweatandtearsforeverl9833
2 жыл бұрын
I wonder what would happen if I used a brass wire on my welder
@ElZamo92
2 жыл бұрын
Machining stuff in imperial units… it hurts my soul…
@Gunth0r
2 жыл бұрын
bro, your dry run was super wet, it almost made me edge again
@tdg9281
2 жыл бұрын
Love all of your videos but why are you guys using the imperial system instead of metric ?!? It is literally superior in every aspect
@TITANSofCNC
2 жыл бұрын
And Love you🤙🙏 In the US, 99% of small and large companies use Imperial. We have great respect for our Global audience though and in all machining videos we offer speeds, feeds and all parameters in both imperial and metric.
@andy86376
2 жыл бұрын
So it is falling apart already? or are these loose pipes separate?.
@metalextras
2 жыл бұрын
3D Printing is still an open book technology, dependent on the material, plastic, alloy or low melt metal can be done with precision finish, other than that, still need precision deburring and coating to cover all those porosity...
@ChevTecGroup
2 жыл бұрын
You know that the most successful space launch companies use 3d printing to build the majority of their engine parts?
@BenWilson24
2 жыл бұрын
The as-printed parts are >99% dense and virtually 100% dense after HIP
@madebym.e.
2 жыл бұрын
Very interesting is the machine made in germany?
@gertkristensen6451
2 жыл бұрын
3d printing you can make fantastic parts but you cant make the parts in the real wold .. edm machining and mold you can make parts
@BenWilson24
2 жыл бұрын
I 3d printed end use production parts for 5 years at an aerospace OEM and now support a list of contract manufacturers printing production parts for several industries
@darthbane4980
2 жыл бұрын
Well I guess it wasn’t impossible……..
@kiwaycanny6522
2 жыл бұрын
I love Electronic dance Musik / edm
@chananielwizman2401
2 жыл бұрын
I college used kerosene not h20 . Was a ram edm
@diytools6874
2 жыл бұрын
I love EDM.i make every day cuts for almost 20 years and never bored these machines...i think the part has big distance from upper and lower nozzle... this is speed issue!but you make an excellent cut!!
@williamlind2843
2 жыл бұрын
The owner of my company bought some wire EDM machines 15 years ago because we were offloading the work. Nobody wanted to touch them. He asked me and I accepted the challenge. I love it. Bonus is he lets me recycle all the chopped-up wire. It's only about $5,000 every 4 months!! 3 machines run 24 hours a day when they are not getting PM done!
@henryhbk
2 жыл бұрын
My 2 comments would be why not use a water jet vs. EDM for a cut like this? and second of course given a 3D printed part, it's just easier to digitally cut it in the original model with a plane-cut and then print it in halves... but that is of course less cool.
@connorjohnson4402
2 жыл бұрын
precision a waterjet cant make a clean cut or perfectly straight faced cut past certain thicknesses, also how would you print the floating tubes in the middle?
@BenWilson24
2 жыл бұрын
Width of the cut, smoothness of the cut, setup. Typically, the EDM cuts are straight for 3d printed parts, so it's like 5 lines of gcode
@highpointsights
2 жыл бұрын
Did that for about 15 years. I had parts that we ran all the time holding holding +/- .000025. We checked the parts with go/no gages supplied by the customer. At one time Mitsubishi had about 70% market share. That is no longer the case!! Still good machines. Our shop had Fanuc and Mitsubishi!! Fanucs are a very good machine but not nearly as friendly as the Mits!!
@Nocturnal2010
2 жыл бұрын
I use deionized water for all my aquariums. Never even thought about other functions for that water. 👍🏿👍🏿👍🏿
@1shivanox
2 жыл бұрын
Hey, with the IRIS 6, whats possible on surface flatness in .mm² (how straight is the cut) with this kind of technique? greetings from germany
@stanislavtimanov
2 жыл бұрын
Titan, this is simply example, but if you show to produce plastic extrisuon tool - this is GREAT! ONA - the best. Easy to use, low price for parts. I think this better then Fanuc Robocut
@RealWunderBanana
2 жыл бұрын
If only they had 3D printing when carburetors were main stream, they could've made super crazy stuff.
@ambydaly5713
2 жыл бұрын
Is your shop temperature controlled if working to 0.0001”. Also have you got your machine on a substantial isolation base from the main machine shop. If you are not doing this have you got local temperature sensing at the part on the cnc table?
@tomte47
2 жыл бұрын
These are invaluable in the Tool and Die industry, precision combined with the ability to cut hardened steel and even Tungsten carbide. Can make your guys running the cnc mill lazy though :), often if we have say 20 small parts with some simple features and an outer 2d shape you end up making a big block with all 20 in it then you just mill/drill the features and drill starting holes for the edm. So its just one big part in the mill move it to the edm and cut 20 complete parts out, no fixtures etc required. Its not really worth it for very large series since the edm is very slow.
Пікірлер: 290