You sir are awesome:) I am a professional metal fabricator by trade and would not have came to this solution on my own... hurts to say that lol. Perfect though, low speed = no sparks. Sparks are scary in old houses. Solved my problem. Thanks again.
@stipcrane
Жыл бұрын
I went out to harbor Freight and picked up a cheap cut-off wheel for my drill and shortened a duct inside a hard to access joist bay. Worked great! Thanks.
@addismultitasking3504
Жыл бұрын
Cool, have a good weekend
@suzanacarey
4 ай бұрын
I'm gonna try it with my Dremel. Thanks for the video!
@addismultitasking3504
4 ай бұрын
Good luck it should work
@donblue6507
20 күн бұрын
I was just gonna say that , I use Dremels for control cabinets as well does tear up the sheet metal like a saw
@Prash1c
9 ай бұрын
Great video, thank you!! Essentially an angle grinder blade on a drill driver--which is accessible to most average mortals and non-pros. An angle grinder, sawzle, and drill-driver are probably a good 3 to have at your home at all times for stuff like this.
@addismultitasking3504
9 ай бұрын
Great point!
@JodiSamurai
2 ай бұрын
Great demo boss man!! .. But, I would have to write you up for handing sheet metal without gloves..
@addismultitasking3504
2 ай бұрын
LOL
@sardulsamra1518
2 ай бұрын
Very Very helpful video. Thanks 🙏
@addismultitasking3504
2 ай бұрын
Glad it was helpful!
@hal8683
Жыл бұрын
Wow !!! Glove up for any metal work! do NOT reach in a metal cut or sandpaper without good gloves etc. Be Happy and ?
@NullDogma
Жыл бұрын
a pair a red and greens will do the job.
@KingMorgh
Жыл бұрын
I bet you the oscillating tool would work nice
@billysmether6237
10 ай бұрын
Nice! Great video!!!
@addismultitasking3504
10 ай бұрын
Thanks!
@thehamburglar9mm
Жыл бұрын
Not much of a welder, but one hell of a grinder.
@addismultitasking3504
Жыл бұрын
lol..thanks for watching
@Betoche-rr3sb
Жыл бұрын
Hi, how did you measure the hole?
@burrmanchu687
Жыл бұрын
Just use a Dremel with a little cut off wheel?
@addismultitasking3504
Жыл бұрын
That works too
@hal8683
Жыл бұрын
Dremel may do it also ??
@KAT-df7ey
2 жыл бұрын
Great video! I've been trying to learn how to cut kitchen ducts, but there's grease I dont want any sparks it might cause fire. Do you think your method would work? I'm surprised you didnt get sparks too
@addismultitasking3504
2 жыл бұрын
Go slow , there will be slight sparks
@billsharp896
2 жыл бұрын
Really appreciate your video. I've been trying to find a better way to cut into my ducting than with snips. Can you please comment on using what appears to be a cordless drill to this. In the SHARK cut-off wheel product description it says to not use an electric drill, use min 20,000 RPM to max 25,000 RPM . Did it work ok with a regular drill? Thanks
@addismultitasking3504
2 жыл бұрын
you can use any drill just vary the speed with your finger, those cut off wheels will explode if you rotate them too fast
@billsharp896
2 жыл бұрын
Understood & thanks!
@ajellyraccoon7143
2 жыл бұрын
Could you use an oscillating tool with a metal blade?
Пікірлер: 30