LOL saved my ass. I was fighting with a pin for way too long thinking I must be missing something. Searched for depin Denso ECU connector and luckily your video came up. I thought that pin lock was just a mold mark. Learn something new every day!
@iwiresubaruwiringsolutions5538
4 ай бұрын
Glad you found it useful!
@occamsrazor1285
Жыл бұрын
A little tip: don't pull on the wire "prematurely". You'll bind the locking tab in place and you won't be able to lift it up. Instead: push the wire in to remove any tension on the tab, the push the depinning tool from the front of the connector and lift the tab, then pull the wire out of the back of the connector. Also not that all 5 of the depinning tools are different. If the tool you're using won't fit, look for one that will.
@MixaL1s6804
6 ай бұрын
what if i did what u said not to do? i cant get a pin out. pulled so hard after, the cable cut off and there is only the pin inside the connector, with the locking tab messed up in there idk what to do and i need this plug asap
@occamsrazor1285
6 ай бұрын
@@MixaL1s6804 What kind of connector? You might want to order a new one.
@subbaraoganeshna7268
Жыл бұрын
Thanks for the video. What those male pins called ? I have to add new wires to harness, so I need those male pins. But don't know the name
@iwiresubaruwiringsolutions5538
Жыл бұрын
We carry them here. iwireusa.com/collections/ecu-replacement-plugs
@edgeofneptune7088
Жыл бұрын
Really appreciate the video. I was getting ready to drill out a male pin which had broken off. Thanks to your instructions I was able to remove the pin without damaging the housing.
@NewShockerGuy
2 жыл бұрын
Great vid. Appreciate it. Had to depin a t-harness for my Lexus so that I could tap into wires and properly heat shrink it. I didn't want to cut the wire. This was perfect!
@ghostpunkkilla
3 жыл бұрын
I need this to replace both shells on the body side of my engine harness, the captive clips broke.
@wrx8xb
2 жыл бұрын
I'm agitated with myself that i didn't search for this video sooner. hahaha. you guys are the best.
@fsarachu
2 жыл бұрын
thanks, you saved my harness from being stripped
@alexfeaizi
2 жыл бұрын
Thanks for the information!
@keshersimonelli1417
2 жыл бұрын
You guys are legends ty
@zippack999
3 ай бұрын
Can you make a video on how to do the bulkhead harness avcs for the 207/257 swap
@iwiresubaruwiringsolutions5538
3 ай бұрын
No video at the moment. We do include step-by-step instructions when you purchase the harness.
@hekterr6677
2 жыл бұрын
Do you guys have a source for the actual pins themselves or sell pins?
@brandons.3177
Жыл бұрын
thank you!
@trojangpete8
Жыл бұрын
Not as easy as it looks depining the small whole on the ecm. I have the special tool and it still does not loosen the terminal.
@iwiresubaruwiringsolutions5538
Жыл бұрын
For sure, we make it look easy with our experience. Make sure the lower lock tab is released though.
@amsrilanka6892
10 ай бұрын
Thanks bro
@manolitolicup5941
2 жыл бұрын
Do you have any depin tools for nissan?
@iwiresubaruwiringsolutions5538
2 жыл бұрын
If the ECU connector looks similar it would work on a Nissan as well
@Arielxx01
2 жыл бұрын
It's impossible
@iwiresubaruwiringsolutions5538
2 жыл бұрын
With the right tool and patience you can do it :)
@Arielxx01
2 жыл бұрын
@@iwiresubaruwiringsolutions5538 not if i totaly destroyed it by using too much force xD
@iwiresubaruwiringsolutions5538
2 жыл бұрын
@@Arielxx01 oh no! Good thing we sell replacements ;) iwireusa.com/collections/ecu-replacement-plugs
@jyu0715
Жыл бұрын
shit, same here, been trying for two hours.. its the same connector for honda k series
@Arielxx01
Жыл бұрын
@@jyu0715 you have to figure it out, it's simple after you understand it. Get a light and look inside depined connector
Пікірлер: 29