This is crazy. After watching, about half of this video, seeing him fumble, springs and plastic pieces, I grabbed a small dental pic with a hook, reached in underneath the safety latch, where I could clearly see the spring, ripped it out with the hook. Done. Don’t waste your time tearing this whole thing apart.
@PhillipBlanton
2 жыл бұрын
Thanks for this video. I just picked one up on Saturday and HATED that "feature". I googled "Micro Torch disable safety button" and found your video. Mine was assembled slightly differently than yours but otherwise identical. At 2:25 there are two silver screws visible. You removed the right one to take the top mechanism off. On mine, which was identical in every way except for this, that screw was installed in the silver, rectangular hole to the left of the lock lever instead of the hole it was in yours. Otherwise the process was the same. Additionally, on yours, you removed the switch AND the spring, but on mine I removed only the spring that pops that little switch back up after you push the ignitor in. I put a tiny drop of super-glue into the bottom to hold that little switch down so it didn't rattle. After it was all back together, I filed down the tiny plastic tab that now protrudes beneath that switch so that it looks nice.
@MatthewTimbs
Жыл бұрын
Yep mine was the same. Bernzomatic brand
@onefastbob
11 ай бұрын
Pull the safety tab down to it's locked position. Using 2 part epoxy, glue the safety tab in the locked down or on position. Done, no need to disassemble anything.
@BJ-on4wj
2 жыл бұрын
If you don't want to do all that I just super glued mine in the down passion and it's been holding for over a year
@OrcinusLaryngologist
Жыл бұрын
Working still?
@BJ-on4wj
Жыл бұрын
@@OrcinusLaryngologist sure is the only problem I'm having with it is the spark ignitor is starting to go out but that's a easy fix
@OrcinusLaryngologist
Жыл бұрын
@@BJ-on4wj I put a safety from a Bic in there. The curvature & locking edges of it make it seem as if they engineered it to be done that way. It’s so perfect - wish I could post a photo.
@hellhammer4041
Жыл бұрын
You don't have to take it apart.Just get a little pocket knife and stick your knife under the safety and pop it out. Make sure you get the Spring that goes with the Child safety out as well If It stays in there it will keep the hammer from Stricking and the Continuous flame switch From Latching. so when you Pluck the little plastic child proof thing out make sure you pluck the Spring under the trigger out As well. They will be a little space under the trigger now but I believe it will let more air go into the lighter and let it breathe and keep it from getting as hot.
@MatthewTimbs
Жыл бұрын
I picked up a Bernzomatic torch secondhand that looks different (gray plastic outside and yellow buttons) but is almost identical inside. one difference is the screw that holds the main burner assembly to the body. ON yours it was on the right side (away from the fire end) and on mine it was on the same end as the business end. Beside that your instructions were spot on. I missed the little square valve actuator part the first try but it worked otherwise. Also the screws are very cheap so be careful not to strip them. the one holding the button spring stripped on mine, I had to cut a new slot with a file but it took all of 5 seconds to do that.
@venticated6012
Ай бұрын
awesome now my torch is broke lol
@joshwarodriguez7103
Жыл бұрын
You saved my life mate have a great life mate🙌🏽
@markharris2539
3 жыл бұрын
Was hoping there was a way to just jam it open. Bummer
@bigfranksworld
Жыл бұрын
Just what I needed. Thanks!
@ronsnow8342
3 жыл бұрын
Thank you for posting this.
@95Z28A4
4 ай бұрын
Awesome content. Camera skills.......not much. Thanks for the help!
@justinpaul9424
Жыл бұрын
Thanks for the help
@JohnnyG1956
Жыл бұрын
I have two of these and performed this procedure on both. The only deviation from this procedure is that I nipped the top of the child lock off with wire cutters and put it back in place with some super glue. It probably doesn't make a functional difference, but mine look original (no home under the "flame on" button.)
@jfbreese
Жыл бұрын
Thank you!
@danacarbone9405
3 ай бұрын
Mine does not keep the flame!!!!!!!!!!!!! I have to click it 5 or 6 times then it just goes out again. I can hear the gas flowing but why does it go out??????? always. I justfill it and it does the same thing
@kalebtodd2618
3 жыл бұрын
so, while i was doing this, my gas line disconnected and now will not work. is there a way to trouble shoot that
@manchildrc
2 жыл бұрын
The easiest permanent solution to take a pair of needle nose pliers grab the safety clip by the bottom and twist it it'll break once it breaks you're in business
@OrcinusLaryngologist
Жыл бұрын
Yeah but you also have those who don’t have that dust a ship in a bottle-gingerly. 😮
@timhales8906
3 жыл бұрын
do what i did and glue it open,been holding good for a year
@chronicironic1358
3 жыл бұрын
Does the torch still work?
@OrcinusLaryngologist
Жыл бұрын
Glue it open? Wouldn’t the glue wear away quickly from rubbing on the igniter button? How’s it holding up?
@markbrown1609
2 жыл бұрын
not if you got some little firebugs running around the looking for trouble.
@jacobakelly01
3 жыл бұрын
is there another spring you missed?? I have two extra springs and have no idea where they go. Also, my continuous stopped working like it's missing a spring. I've watched the video like 4 times. Please help
@amymarie9380
2 жыл бұрын
Hey did you ever figure this out because the exact same thing happened to me!!! Lol it's driving me crazy cause the push lock is just loose asF
@AbnormalityTV
3 жыл бұрын
You don't need to do all this just put a Lighter Safety inside the slot after you push the safety down and jam it inside, it won't come out and its not in the way. So much easier than taking it all apart trust me plus if you have a warranty it wont void it because you can just take it out, *So if you have a warranty I don't advise you doing this idea because you will void the warranty, my method does NOT*
Пікірлер: 30