An engine normally needs 100lbs compression minimum to start and run with any kind power. If the cylinders vary more than 10%, add a teaspoon or so of motor oil to the weak cylinder and see if the compression goes up any. If it does, the rings are probably bad. The rings may also be washed out with too much gas too causing low compression. f it doesn't, the valves are probably not seating correctly or burnt or bent. Keep up the great job Jason. Always waiting for the next video. 👍👍
@kingofpressurewash
5 жыл бұрын
You are absolutely right bout all the above. That info is in my head but hasn't been used to much sense college 20 years ago.
@bluewatermarketing3338
5 жыл бұрын
You Sir are the most hands on and love watching your videos. learning a lot. thanks
@kingofpressurewash
5 жыл бұрын
Thanks
@aceshigh235
5 жыл бұрын
Clear, Concise and informative - well done!
@kingofpressurewash
5 жыл бұрын
Thanks for watching
@libertypowerwash9904
5 жыл бұрын
One of your best videos 👍🏻
@kingofpressurewash
5 жыл бұрын
Thanks I try
@nendymaharna3938
10 ай бұрын
Over all, for u best gx630 or gx690?
@keithdittmar1701
5 жыл бұрын
Thank You! This could be very useful.
@kingofpressurewash
5 жыл бұрын
Thanks for watching
@TheGregWallace
2 жыл бұрын
Comment........Can you suggest what the best battery would be for starting this motor?
@TheSkyhawking
5 жыл бұрын
Jason nice job. Quick question did you get it back up and running. After doing all that...Thanks
@kingofpressurewash
5 жыл бұрын
edward yack yes I put new plugs in and change the oil. Started right up and ran perfect
@country6368
5 жыл бұрын
Can u do a video in how to check your gallons per minute if there’s a way to make sure it’s accurate to what the label says thank you
@kingofpressurewash
5 жыл бұрын
For downstream or mixing valve or both
@country6368
5 жыл бұрын
Power Washing well both if u dont mind sir and how can u tell your mix ratio if u down stream straight SH with a 5 gpm machine
@kingofpressurewash
5 жыл бұрын
Depends on what injector you are using
@country6368
5 жыл бұрын
Power Washing i took the tip out my wand and turned on my machine shot water in a bucket and timed it fir one minute it was about 3/4 of a inch from top of the bucket should i do that with a tip in or not
@kingofpressurewash
5 жыл бұрын
@@country6368 tip out you can try tip in also
@CRTRUCKING113
2 жыл бұрын
Thanks for your help 👍
@RIATAC451911
3 жыл бұрын
My gx610 keeps blowing the dip stick out. Any ideas?
@kingofpressurewash
3 жыл бұрын
Might have a compression part problem
@RIATAC451911
3 жыл бұрын
@@kingofpressurewash I didn't know if these engines had a pcv valve/filter that might cause this, or if the the rings are shot.
@pierredery7350
4 жыл бұрын
Thank you help run my honda 690 motor
@jossr71
4 жыл бұрын
i have a gxc690 with no spark. i replace the coils and new spark plugs and still no spark. i also disconnect the oil sensor and still don't have spark. do you have any idea what the problem might be?? i i was told to check the compression, is that has to do with no spark? i really appreciate your help thanks
@kingofpressurewash
4 жыл бұрын
Check the fuse behind the switch. That should have nothing to do with it but I will still check it. Make sure there’s no wires unhooked right there behind the ignition switch
@berniemac8413
Жыл бұрын
Did you ever find out what your issue was with the no spark? I have one and it doesn’t have any spark either.
@jossr71
Жыл бұрын
@@berniemac8413 it end up being a relay, if the spark is not strong
@berniemac8413
Жыл бұрын
@@jossr71 a relay? Where is it located?
@jossr71
Жыл бұрын
@@berniemac8413 it only has one relay, should be somewhere in there
Пікірлер: 33