This is years of experience here. Great video. Keep them coming.
@GunSmoke098
Жыл бұрын
Closed end of a 13mm wrench slides right over parking brake cables and disengages the fingers.
@TheBFHGarage
Жыл бұрын
Never thought about that... I'll have to try that next time! 👍👍
@tsmith578
Жыл бұрын
Hey Mike,. Here's something for you to try for removing parking brake cables,. Find yourself a old old hold down spring from some drum brakes and clip / cut / grind the ends of it You can thread it on the parking brake retaining clip to release the tabs from the bracket. I have used this method for a lot of them with pretty good results. Thank you for your videos. Tim from Wisconsin.
@mefistofer
Жыл бұрын
So professional Mike, great work! I have to replace the control arms on my Cherokee due to wear this will help a lot!
@Burke_Motorsports
Жыл бұрын
That flex starting at 1:34 had me rolling. 💪
@mycomputerguylarry
Жыл бұрын
Thanks for the video I am doing this in a month or so...
@ScrapMetalJr
10 ай бұрын
a 13 mm box end makes quick work of those brake cables, esp a ratcheting wrench. slide over cable and with a few spins they pop out.
@dangelo5427
Жыл бұрын
Going to save me so much time. Great video. Thank you
@DonNagel9250
10 ай бұрын
Excellent advice and video!
@eliinthewolverinestate6729
Жыл бұрын
I had so many problems with dana 44a in wj. I swapped in a dana 35. My dana 44a had the more expensive axle shafts. The bolt in ones for the locker.
@Thundarr995
Жыл бұрын
Whenever I take those phased drive shafts apart,now anyway, 😂I mark it in 2 different spots, with 2 different colors. Just in case the paint somehow gets wiped off. Awhile ago I replaced the carrier bearing on my S-10 drive shaft. I marked it,but the paint mark got scraped off when I removed the bearing. I didn't realize it until I installed the new bearing and I couldn't find the paint mark on the splined shaft. Lucky for me,It only went together 1 way. The factory made 1 of the splines extra wide. Not all of them are like that through. That would've been really bad if that drive shaft didn't have that because that truck was my only transportation at the time.
@robertware8643
5 ай бұрын
I’m building a new rear axle housing Dana 44 4.56 it’s going to be fun
@TheBFHGarage
5 ай бұрын
Lots of fun and don't forget to check out my other videos detailing axle work!
@robertware8643
5 ай бұрын
Roger that!
@robertdoran7387
Жыл бұрын
Got a 2003 Wrangler X with D30 front and D35 rear. Hoping I can just buy a Rubicon D44 and bolt it right on the rear suspension parts.
@trashandtrail
Жыл бұрын
Awesome!
@kyleharris3
5 ай бұрын
Do you not have to change the front gears to match the rear?... I've always heard if you change one, you have to change the other.
@TheBFHGarage
5 ай бұрын
Yes absolutely!
@TwoFeatherChannel
Жыл бұрын
could he put Bump Stop Pad extensions, so the bump stop hits the pad extension to bottom out before the shock bottoms out?
@TheBFHGarage
Жыл бұрын
That's exactly what you want to do... Just not 5" worth
@shawnt1975
Жыл бұрын
@@TheBFHGarage I hate it when my shock is to long
@tylerdeal1498
11 ай бұрын
can you use the d 44 with stock driveshaft and no sye? I have a 35 now and looking to upgrade.
@TheBFHGarage
11 ай бұрын
More than likely you will have to get your drive shaft shortened by an inch. The D44 is one inch longer. Sometimes people don't have to, so be sure to measure.
@tylerdeal1498
11 ай бұрын
@@TheBFHGarage ok thanks will do.
@josearguello6989
Жыл бұрын
does he have a SYE without adjustable control arms?
@TheBFHGarage
Жыл бұрын
Yes. Small lift so SYE isn't truly needed but they bought it that way. If they increase lift, they will need adjustable control arms.
Пікірлер: 28