Crazy how long that takes but looks so good when it's done!
@rc_1996
2 жыл бұрын
HELL YES!!! So many hours in it!!! Thank you my dude.
@josephloveall8663
2 жыл бұрын
Could you put stars in the sliding door where the sunroof is so there isn’t a huge bald spot or?
@rc_1996
2 жыл бұрын
Yes. It is possible
@304trails8
2 жыл бұрын
Turned out sweet I was really paying attention to your fiber management. Just did mine, a pano roof as well I got half way through and decided I wanted to tidy up the fibers and I had a rats nest lol ended up pulling out 100 fibers to try and beaten things up when I put them back. Worked about 20 percent haha. The other half I dived up into 20 piece bundles and taped the. About every two feet to keep all of them separate and it worked out 10x better but I still have a big bundle of mess in the back running across the headliner. How did yours fit back up with the sunshade motors I see only really one channel for the fibers to lay out of the way I’m hoping my bundle will fit up in there.
@rc_1996
2 жыл бұрын
I just sat that one back in that truck and made sure it wasn’t gonna catch on any pieces of moving parts. What I would suggest if you are worried would be to buy a roll of black duck tape, and go from edge to edge on backside of the headliner on both sides to hold down those fibers. Just make sure you don’t put tape on any areas that are visible from the front. Should make sure any and all fibers that are around the sunshade and motors don’t get caught.
@tattooguy302
Жыл бұрын
Thanks for the insight! Just wondering, why could you not drill through the plastic areas surrounding the Center opening? Does it have some function which would be affected by drilling a few holes through it? Thx!
@rc_1996
Жыл бұрын
U can drill it but you take a very high risk of catching the headliner with the drill bit and destroying the headliner material. U can go thru the plastic but not with a drill bit.
@tattooguy302
Жыл бұрын
@@rc_1996 Ahhh. Gotchya. Just what a project like this needs, a challenge. Lol. Where’d you end up mounting the projector and how’d you power/wire it up? Thx!
@rc_1996
Жыл бұрын
@@tattooguy302 I mounted it under the rear driver side seat and ran ground wire to seat bolt and power wire to ignition on fuse.
@larretta88
8 ай бұрын
How did it hold up to the huge leak in the sunroof? Jw? They all do it right?
@clxrrk8061
Жыл бұрын
Just used a drill bit to drill through the headliner? I’d be worried about it snagging the headliner.
@rc_1996
Жыл бұрын
No. Can’t use a drill bit or it will snag
@clxrrk8061
Жыл бұрын
@@rc_1996 Ahh okay, what’d ya use?
@bigeasy2187
Жыл бұрын
i came here to see how you get the headliner out but you didnt show it
@rc_1996
Жыл бұрын
Gotta pull all the seats and center console and then pull out driver rear door
@jesusdominguez4619
3 ай бұрын
How many stars did you put
@grantweaverling7871
Жыл бұрын
What length and how many piece did u use
@evanchadbourne5343
Жыл бұрын
Where did you place the Optic light box ? In the pillar ?
@rc_1996
Жыл бұрын
No. It is under driver side rear seat.
@evanchadbourne5343
Жыл бұрын
Last questions lol, when you took the front seats out did you have to worry about the SRS system, disconnect the battery etc.? Or did you just disconnect the wire harness and bolts ? Thanks
@rc_1996
Жыл бұрын
@@evanchadbourne5343 I disconnected the battery so there was no power then unplugged the seats and center console.
@evanchadbourne5343
Жыл бұрын
Thanks for the quick responses, been thinking about doing this my self!
@Andrew-rq9sm
Жыл бұрын
What fuze you tapped into brother
@rc_1996
Жыл бұрын
Any ignition key on fuse. Typically it’s a 10amp
@SauceMiller69
4 ай бұрын
How do you get the headliner off
@rc_1996
4 ай бұрын
Pull it out threw driver rear door
@SssandNBtwnMytoes
Жыл бұрын
Wouldn’t it have been easier to have the front windshield removed by a glass company to get the headliner out then rip apart your interior
@rc_1996
Жыл бұрын
Yes but more costly and timely. If customer wants to pay the extra I would do it.
Пікірлер: 35