As well you can predrill 1/2" plywood as a gide for the diamond bit. then center over the counter, you will be able to see where the center is nicely, and then tape it to the counter. As long as you don't push hard when starting drilling with the diamond bit, it will stay in place, and the bit won't walk away from where you want the hole to be.
@FortKnoxCo
6 ай бұрын
Great suggestion 🤙🏼
@BlazeBoltMarketing
25 күн бұрын
very helpful, thank you for sharing
@FortKnoxCo
25 күн бұрын
Your welcome 🤙🏼
@xxxplorer50
10 ай бұрын
Thanks for a very simple but informative video. Keep up the good work.
@FortKnoxCo
10 ай бұрын
Thank you and you’re welcome. Glad you found it helpful
@polygrafix
8 ай бұрын
Did this today, flawless execution. Thanks so much, my wife was worried i was gonna break the countertop, but i watched this video 3 times before doing it
@FortKnoxCo
8 ай бұрын
Nice! Good job! It’s pretty cool to get it done. It’s scary your first time drilling into a nice countertop. You just gotta go for it and like you said, watch it 3 times to make sure you aren’t missing a step. lol. I practiced on a piece of old cut off waste countertop before my first time. I’d even go as far as buying a small scrap from a store to try on if in doubt.
@Greenlighters100
3 ай бұрын
@FortKnoxCo Great video. This gives me confidence to do it. So I'm assuming a good, high quality bit isn't one and done and that a practice hole won't ruin it?
@Narikvp
2 ай бұрын
Question: I have a Dewalt 20V Max Drill. Will that be sufficient power for this kind of job if I use the Milwaukee Diamond bit you mentioned in the video? 2nd Question: Can a 12V power tool work well on granite or quartz? What would you recommend for grinding away some material from a granite cutout to accommodate a slightly (1/16 inch) bigger cooktop, for example? Would a 12V angle grinder work, in your opinion, or should I be going with a 20V power tool for such jobs?
@FortKnoxCo
2 ай бұрын
Botha questions Yes. It can be enough so long as you don’t over work the tool. Let the tool and bit do the work, don’t apply too much pressure on the tool/bit while it’s grinding. Take your time with it.
@Narikvp
2 ай бұрын
@@FortKnoxCo thank you so much for answering my questions! Keep up the great work, your videos are highly educational and explain how to do jobs in a clean way!
@FortKnoxCo
2 ай бұрын
@@Narikvp thank you I really appreciate that
@michaelwinalski9013
7 ай бұрын
This is so helpful. Random question, can you share what faucets you're installing here? The set looks awesome. Thanks!
@FortKnoxCo
7 ай бұрын
Yes of course. I just updated the video in the description I put the actual items links. And the video itself now has links showing the items as well
@michaelwinalski9013
7 ай бұрын
@@FortKnoxCoawesome thank you so much. Great videos man!
@FortKnoxCo
7 ай бұрын
@@michaelwinalski9013 no problem at all 🤙🏼 thank you
@michaelwinalski9013
7 ай бұрын
Last question, do you align the RO hole with the larger sink hole or do you always do 2” from the end of the counter regardless of the primary faucet?
@FortKnoxCo
7 ай бұрын
@@michaelwinalski9013 its kinda personal preference. No matter what you decide, for the faucet to be in a Proper place to function correctly, you will be pretty close either way. Really it will depend on the type and style of faucet you buy. You just want the faucet to reach far enough into the sink so you can fill your bottles or cups without having to til your containers. Ideally you’d like to be able to sit your container plumb vertical in the sink and let it fill. You just don’t want to go to the extreme of getting it too close to the rim of the sink and risk cracking your countertop by making it brittle. Also look under the sink and see how your sink itself sits. You want to plan ahead if you will be running into the sink rim. Some under mount sinks have a larger flange/lip and when you cut your hole you may have a little bit of that sink lip you might need to cut away to let you faucet pass through properly to secure it from underneath
@RedShiftMusic
4 ай бұрын
Great video thanks!! I just drilled through my quartz counter with your help. My core bit also had a pilot bit, so I started straight. I used a wooden template clamped to the counter to ensure the bit wouldn't walk before it bit into the material. Once the core ring started to dig into the material I removed the pilot bit and continued just using the core bit. Add plenty of water. And protect any wiring that might get wet below your sink. Good luck!!
@FortKnoxCo
4 ай бұрын
That’s great to hear! Good job!!
@kimberella2105
3 ай бұрын
I think I’m Gna give this a try. As a female they’re always trying to rip me off for installation services. If I can install a garbage disposal then I can do this!. Off to Home Depot so I can buy the drill bit. I’m a little nervous. Drilling into granite will be a first for me
@FortKnoxCo
3 ай бұрын
You got this. Just like in the video. Just make sure you have your hole marked where you want it and when you go to use the drill have the speed on high and just start by ringing the edge of the bit to touch the edge of the line where you want it. Let that edge of the bit start to do it thing and make a groove in the surface. Then you can gradually rock it vertical to a straight up n down position and you good. Then it’s just being patient to let the bit do it work.
@steves.9440
2 ай бұрын
I’m glad I came across this very informative "how-to" video you created. You explained each step very clearly. . I have been putting off this exact project for far too long. Now, after watching your video, I have the confidence to proceed.
@FortKnoxCo
2 ай бұрын
I’m very happy to hear that. It’s exactly what I was going for. I really wanted to show people this can be done and not to be intimidated by it. Thank you for finding my channel 🤙🏼 it’s much appreciated
@GunsAndFishingU.S.A.
2 ай бұрын
I am not handy lol i am afraid to do this. I just bought the reverse osmosis filter
@FortKnoxCo
2 ай бұрын
It can be a little intimidating for sure. It’s scary to cut into a beautiful counter top. But you can trust the process. If it’s worth your time you could buy a small scrap piece or quartz or even thick tile and practice cutting holes into that before you try on a counter top. It’s the same thing for each type of of surface. It’s all about taking your time and getting the first edge to cut in a little bit before your rock the drill full vertical
@GunsAndFishingU.S.A.
2 ай бұрын
@@FortKnoxCo ok thanks 🙏 God bless
@1323GamerTV
7 күн бұрын
I love how unnecessary having 2 reverse osmosis hot water dispensers in a kitchen
@FortKnoxCo
7 күн бұрын
Yeah this is a second one across the kitchen it a sort of “butlers pantry” area with a sink. It’s a little excessive but nice to have. And I wanted to film a video of the process so there’s that too. But it’s not hot water, they are both off of the cold water line. Maybe more like “ room temp” water dispensers
@marvin7048
6 ай бұрын
I’m gonna try to replicate this. Watch me mess it up somehow
@FortKnoxCo
6 ай бұрын
You can do it! 🤙🏼 Slow and steady. Scariest part is starting that edge of the drill at an angle. The rest is easy.
@ladyluck5248
7 ай бұрын
Thank you. Like we gals say : if you want it done do it yourself … Off to Lowe’s for the bit. I’ve had a soap dispenser sitting here and I’m going to have to do this myself …. Thanks !!!
@FortKnoxCo
7 ай бұрын
Hahah. Thats awesome. You can do it for sure. Just take your time and let the bit kinda work its way in. Starting that first edge is the most nerve wrecking. After that you’ll see it’s simple.
@RichestTea
Ай бұрын
More water, cut a hole in a paper cup and use that as a shroud around the blade.
@FortKnoxCo
Ай бұрын
That’s a good idea 👍🏼
@AlexRodriguez-do9jx
4 ай бұрын
Will that bit cut through a stainless steel counterop as well? Bc i have a dekton countertop but but my my stainless steel undermount sink extends out like 2-3 inches underneath so if i do this i am hoping i cam cut through both w/out any issues
@FortKnoxCo
4 ай бұрын
No, the stone cutting bit will not cut through the metal. But all you do is get a metal hole cutting bit to cut through that part. The metal cutting bits are way more common and usually less expensive. They are usually metal/wood cutting hole saw bits.
@jenngoodger2036
Жыл бұрын
Thanks for a clear and concise demonstration! Takes the stress out of it.
@FortKnoxCo
Жыл бұрын
You’re very welcome. It’s definitely something you can do yourself and save some money.
@abl3to
3 ай бұрын
Great video, not only did you explain how to do it but I really liked when you explained why. I'm planning on doing this too and glad I came across your video, thanks!
@FortKnoxCo
3 ай бұрын
Thank you for that. I appreciate it. I try to make sure the videos have some really value and not just wasting peoples time. I really want ppl to be able to learn the process.
@nalanimulcahy8451
3 ай бұрын
I'm just drilling into a laminate countertop but I'm subscribing, your instruction and close up filming are both next level. Absolutely fantastic - and you don't shout!🥰
@FortKnoxCo
3 ай бұрын
Haha, I appreciate that. I do try to actually put some value in the videos I make and have information that I feel I would have wanted to know. I truly want people to try stuff themselves and have the confidence to do so. It’s a great feeling
@hellapellanyc6465
9 ай бұрын
Hi, when drilling hole for faucet I've realized the 1" hole is even too big. They recommend 1 3/8. Don't understand why they recommend the holes so big?
@FortKnoxCo
9 ай бұрын
Yeah. I’ve always still measured the fixture to my drill bit to make sure I’m close. I’ve done the recommended size and found the same that it’s a little too big. Maybe they figure the flange at the base will just cover it up but it’s better to have a snug fit so you have more to tighten down around.
@JamesJinZo
3 ай бұрын
Is DeWalt DCD799 strong enough to drill into quartz & granite counter?
@FortKnoxCo
3 ай бұрын
Yeah. Any basic drill can do it. You just need to let the drill do the work. Don’t slam it or put too much manual pressure on it. Let the drill bit do its job and be patient. The power and rpm’s or the drill will be fine.
@sre2007
9 ай бұрын
What is your thought on taping the surface to prevent damage in cause of some mishap? Like at the end when it punched through.
@FortKnoxCo
9 ай бұрын
You could but the tape won’t do much when that bit hits the surface. Unless you had something really thick. But you would t want to be cutting through the tape with the diamond bit. Could gum it up. But if you taped around the outside to help prevent it wouldn’t hurt. They do sell stick down and suction type guides to help with making sure the bit goes straight down and doesn’t run on you. But most just use the tilt in technique. There’s several ways to accomplish this. Just depends on how much prep or money you want to spend on the tools needed. There’s some fancy set up to make it easier for sure
@robmuld2685
15 күн бұрын
Thank you very much for this video! I wasn't going to do it at first, but you gave me the confidence that I could. The execution was flawless and I saved a ton of money by not paying someone else to do it.
@FortKnoxCo
15 күн бұрын
That’s exactly why I made the video!! So awesome to hear this. It’s really why I like making videos in general. I know ppl are capable of doing a lot of things themselves and it feels good when you get something like that done. 🤙🏼🤙🏼 good job!
@samuelspade889
3 ай бұрын
I guess trying to make a pilot hole would face the same problem of a walking drill bit.
@FortKnoxCo
3 ай бұрын
Yeah. There’s a few ways to keep it centered. Seems like everyone I see just does the tilt in method though. Works really well once you try it a couple times
@sergiojimenez2525
8 ай бұрын
Good job, thank you. Best advice; don’t good cheap.
@FortKnoxCo
8 ай бұрын
💯. Spend a couple extra bucks to have a tool that will make you life a lot easier.
@SlightlySlanted
10 ай бұрын
Wow love your videos!!! So useful and informative!
@FortKnoxCo
10 ай бұрын
Thank you
@BrianKlesmith
10 ай бұрын
Exactly what I needed. Much appreciated.
@FortKnoxCo
10 ай бұрын
Awesome. Your very welcome
@ChuPapi74
3 ай бұрын
Just did this and worked perfectly. Still a little nerve racking. Last .25 inches took a little longer than I thought it should 😂. Thanks for the help dude!
@FortKnoxCo
3 ай бұрын
That’s awesome you did it. I know how crazy it is to take a drill to a nice countertop. But it can be done. And with each time you build more confidence. Happy I could help 🤙🏼
@ChuPapi74
3 ай бұрын
@@FortKnoxCo Absolutely! Jesus loves you my dude!
@FortKnoxCo
3 ай бұрын
@@ChuPapi74 🙏🏼
@r.z.2263
3 ай бұрын
Thank you so much!!! will do it myself soon! :)
@FortKnoxCo
3 ай бұрын
That’s awesome to hear. You got this!
@tomdavis3495
10 ай бұрын
Do you happen to know how many holes you get out of one of those bits? Thanks
@FortKnoxCo
10 ай бұрын
I’ve drilled over 20 and it’s still kicking. It also depends on how well you take care of it meaning, not trying to over press when cutting through and making sure the bit is clean and not overheating a lot.
@tomdavis3495
10 ай бұрын
I use the Milwaukee bits for tile, and I understand how to take care of them due to over-heating. Sounds like it is just the same as tile but thicker! ;))) Thanks for the great video!@@FortKnoxCo
@FortKnoxCo
10 ай бұрын
@@tomdavis3495 oh cool. Yeah then you know what you’re doing. It’s the same thing and the same wear n tear as a tile. I appreciate it 🤙🏼
@carlosz7208
10 ай бұрын
Will this bit cut through stainless steel sink also? My counter guys didn’t have the bit to cut the sink but did cut the hole for the air gap. I think they went 1 1/4 but may need a 1 1/2 bit to enlarged and then cut through the sink. Thanks
@FortKnoxCo
10 ай бұрын
@@carlosz7208 this bit is for stone/tile only. There are similar bits for cutting metal and easily found. They are more common. They have actual teeth on the ends.
@ebfsystem
6 ай бұрын
Anyone knows if the size of the wholes for water filters are standard? 1"?
@FortKnoxCo
6 ай бұрын
Most all do the systems with spigots require a 1” hole. But you can look at the system your installing specs or the spigot your installing and it will tell you what it requires to install
@davee9527
5 ай бұрын
The APEC water systems RO only requires a 1/2" hole.
@FortKnoxCo
5 ай бұрын
@@davee9527 nice! Thats really good to know.
@Serve_one_another_with_love
10 ай бұрын
What is the model number of your drill?
@FortKnoxCo
10 ай бұрын
It’s their 18v drill. Not impact. Not sure on the model. But is the standard found in every display. Around $100 when pricing is right
@bobbrown6682
4 ай бұрын
Great video. Thank you!!
@FortKnoxCo
4 ай бұрын
Your welcome !
@juliogalvez5798
Жыл бұрын
Good job, thanks
@FortKnoxCo
Жыл бұрын
Thank you. I appreciate it
@Gamzesue
5 ай бұрын
thank you for info
@FortKnoxCo
5 ай бұрын
No problem at all
@elliottkelly3861
5 ай бұрын
I did it I can’t believe it
@FortKnoxCo
5 ай бұрын
Nice!! Good job man 🤙🏼🤙🏼
@mortalman6761
6 ай бұрын
Kick Ass Vid!
@FortKnoxCo
6 ай бұрын
Thank you I appreciate that 🤙🏼
@judgeacaseasitstands4879
Жыл бұрын
❤
@FortKnoxCo
Жыл бұрын
Thank you!
@matusala8322
5 ай бұрын
I used spear headed drill bit and it did the job perfectly.
Пікірлер: 92