Ten wirnik po naprawie lepiej świeci niż ta żarówka. Proponuję z tej frezarki zrobić lampkę nocną
@khinmaungtun411
Жыл бұрын
THANKS FOR YOUR SHARING SIR
@pericacvijetinovic1810
11 ай бұрын
Jedino rešenje je ponovno premotavanje rotora. Sve drugo je kratkog trajanja, što se vidi na videu da rotor i dalje varniči a sigurno neče dugo trajati !
@user-iu1zm5jj2i
Ай бұрын
Ova opracija sa šmirgl papirom je posebno delotvorna za kolektor, kolektor joj se toliko raduje kao da ti koristiš šmirgl papir umesto toalet papira
@sonmaniaksan86
2 ай бұрын
Thanks man that helps a lot
@Peter4253
2 жыл бұрын
Great job, thanks for posting👍
@joekaplowitz2719
Жыл бұрын
Thank you for this video! I have an electric lawnmower and the motor is arcing in a similar way to yours. I will try this repair technique👍👍👍
@Nesdayi
Жыл бұрын
Try replacing the brushes first.
@josedelacruzcortez3719
Жыл бұрын
Tengo una cierra de mano y un esmeril Riovi con ese mismo problema y no consigo el mandril gracias por su explicación
@Chiaroscuro1991
Жыл бұрын
Given a choice you want a flat sharp tool (think tiny chisel) to clean out the commutator rather than a pointed one.
@TheReal1953
2 ай бұрын
They make commutator draw blades just for that purpose. I got carried away once on a GM starter and went pretty deep. Sounded like a Mopar starter afterward....lol.Chinese-made router....commutators are cheap if available.
@Klawy07
Жыл бұрын
Za mała lutownica, trzeba było wziąć większą. 🙂
@jcstevegigs
2 жыл бұрын
Great video-thanks! I have an old B&D bench grinder that suddenly stopped while I was using it...hard! It got pretty hot. Now it just buzzes. When off spins freely but turning it on magnetized it and locks it in place. Any ideas? Brushes? Thank you.
@ZutiDIY
2 жыл бұрын
There's couple of things you can check,1 check the carbon brushes 2-your bearings or bushes might worn out,on turning it on armature magnetized to the core.
@jcstevegigs
2 жыл бұрын
@@ZutiDIY I took it apart today. No brushes? It’s a simple motor. Just power to wrapped copper wire and a metal shaft that spins in the center. I checked everything today. All connections good. At one point it started working!! But started buzzing again. Thanks for your help
@officialWWM
Жыл бұрын
@@ZutiDIY I have this same problem with a 12 volt 4wd motor. It spins freely but when I turn it on, it locks up. There is no sign of damage inside but clearly, I’m missing something :/
@Dragon22078
Жыл бұрын
Your grinder most likely has a “capacitor start motor”. The capacitor jumpstarts the motor to get it started. Replace that capacitor.
@marcelopenafiel8659
Жыл бұрын
Your end plate bearings are worn out that's why the rotor magnetized by the stator. Replace it and it will go back to normal operation
@mamengom4446
10 ай бұрын
Bravo mr
@aryaei
2 жыл бұрын
What was the result?! It lights as same problem before any works!!
@russtorque2993
6 ай бұрын
Is that router used for wood or concrete?
@CarlosSilva-vx6vs
6 ай бұрын
Amigo esses fios de prova são em corrente 127v ou 220 12v ou 24 gostava de saber
@oliverelmes179
Жыл бұрын
cuando se puede se puede .buena .
@otonielpacheco5427
7 ай бұрын
Esse seu ferro de solda parece mais um machado dos Apache do Arizona.
@djrival819
Жыл бұрын
Great video but you should get a new soldering iron that tip his humongus :P
@lylegrenoble2055
Ай бұрын
Nonsense!!! Get him a hatchet and a small forge!!!!😂
@joestreet7036
2 жыл бұрын
I dont use sand paper.. I use fine plastic finger mail file or fine metal file.since brushed are even i want the contacts to be even as well send paper will help but better to use something solid like sanding block
@Bot-tv12
Ай бұрын
What did you use to epoxy
@Bianchi77
Жыл бұрын
Creative video, thanks :)
@Xxxcappie23
2 жыл бұрын
So interesting...So all the elongated commutator bars should be in contact. The ones that were not making contact indicated the fault ?? I don't know if I've accurately assessed what's going on here without technical knowledge hehe
@ZutiDIY
2 жыл бұрын
Yes,you got it right
@augustinechinnappanmuthria7042
2 жыл бұрын
Super 💓
@LopesSolucoesemReformas
4 ай бұрын
Show parabens
@lww3988
4 ай бұрын
謝謝您的教導,來自台灣朋友的問候!
@calebcaceres4486
Жыл бұрын
hi how about where can i get the Test lamp
@SamA-xu9gy
Жыл бұрын
Are sparks present even after repairing the device?
@aliallouch5566
11 ай бұрын
The way is completely wrong
@jackmclane1826
Жыл бұрын
That is a hit or miss thing. I had this defect three times. This repair worked once. Be happy when it does. It's a decent machine! But I'm not a fan of applying solder to the rotor. That beast rotates FAST. If you get it out of balance, it will quickly vibrate itself to death.
@seymourwrasse3321
9 ай бұрын
Ryobi is a great piece of equipment...if you like entry level crap. I would rather do without an extra week and buy a real tool
@jackmclane1826
9 ай бұрын
@@seymourwrasse3321 If it works, it works! I know contractors that use ryobi on construction sites. Because the Hilti, Metabo and Bosch Pro get stolen all the time. ;)
@mehmetalicar
2 жыл бұрын
malesef olmadı.hala problem var.ark fazla çıkartıyor..grovler cihazı olmadan kusursuz sonuç elde edilemez..
@sairex5856
2 жыл бұрын
Hi sir,about testing using the light bulb,how u connect the wire because at the video i saw u twisted the both of it.so i little bit confused which one positive & negative.
@palamea
Жыл бұрын
Itu bolak balik gk apa2. Di uji dari tiap titik lilitan itu.
@Jason75913
Жыл бұрын
he probably doubled up on wires for both positive and negative
@gregjohnson5194
3 күн бұрын
@ sairex5856 just letting you it’s alternating current A/C no positive & negative. But I couldn’t tell you why they were doubled and twisted. Nor did I learn how to find the short just look for the most sparks… lol
@Ron56610
Жыл бұрын
I don't understand I still see sparks after you did some soldering it didn't work?
@Ex-fk4nr
3 ай бұрын
some spark is normal too much spark is not at the begining it was sparking too much
@StarFyodperor
Жыл бұрын
It turned itself into AC :D
@nilmanisingh4238
10 ай бұрын
Motor of My ryobi 7.1/4 inch CSB 135L circular saw has become defective. How can I replace the motor?
@juanantoniogarcia5457
4 ай бұрын
Por lo qué se escucha del motor al final y el exceso de chispa en los carbones no quedó bien.
@drgajjar3049
8 ай бұрын
सफाई करते वकत का विडियो क्यों नही दिखाया। कहा से कैसी सफाई करनी है।
@daveese
Жыл бұрын
i don't know how u connect the calble to the lamp, can u explain?
@enesb.114
Жыл бұрын
Seri bağlantı
@black_aura_s
Жыл бұрын
Ору с перчатки твоих бро
@zadvindersingh4234
2 жыл бұрын
Why there are marks on armature core May be armature is touching with field core
@Nick-ye5kk
Жыл бұрын
Remove metal for balancing?
@secobaairways4585
2 жыл бұрын
This really needs audio commentary, it was arcing at the end so it looks to have failed?
@MyJootube
Жыл бұрын
all brushed motors do a little sparking
@Jason75913
Жыл бұрын
@@MyJootube This is what I was looking for, I just bought a rotary tool and saw tiny sparks, was wondering if it is defective, but this video seemed to show otherwise. It is when those sparks become gigantic that I should be concerned then.
@sly901
Жыл бұрын
Are you using solder?
@Jason75913
Жыл бұрын
ya
@joestreet7036
2 жыл бұрын
Haven't seen the light bulb thingyou should show how that is set up
@Wimblex
Жыл бұрын
•.• the light was sort of in series, he cut one side ( either positive or negative)making it a switch which lights the bulb when the two wires are connected together •.•
@djemsjeannitton9792
Жыл бұрын
@@Wimblex you're correct sir
@dc6233
Жыл бұрын
Your 115V test light is doing more damage than good, make a 12V DC test light...
@sumanbaral8457
Жыл бұрын
There is a device called a multimeter….
@haseebqureshir9324
10 ай бұрын
❤
@crankfotton
10 ай бұрын
I like this better .. more fun 😂
@haseebqureshir9324
10 ай бұрын
@@crankfotton 🤣
@jorgecueto9649
8 ай бұрын
This tool made sparks. Multimeters only give values and most of the times these values are very very close to each other, making it difficult to find where exactly is the short circuit in the commutator.
@razer192
7 ай бұрын
@@jorgecueto9649is this a short or has the wire snapped and it's arcing across the wires ?
@seymourwrasse3321
9 ай бұрын
what, are you afraid of leaving fingerprints that can be used against you during the trial?
@bont1059
3 ай бұрын
epic
@juancarlosgonzalezalvarez2489
5 ай бұрын
😊
@ctjohndeere
Жыл бұрын
SHOP VAC. motor 6 months old. multimeter tested armature, field coil, brushes good. motor inop. What's up with this?
@Wimblex
Жыл бұрын
•.• I tried it on my Makita drill but there no change and most of the sparking is on one brush •.•
@wasim91110
Жыл бұрын
Check your field coils .... One is definitely short
@salocinengavac3879
2 жыл бұрын
Ça sert à rien de resouder y'a pas d'étain, le collecteur est soudé par point, c'est à dire une machine
@hansstrouf
2 жыл бұрын
tu n'u pas un plus bros fer a souder ?
@user-nd9bv6zi9g
Жыл бұрын
Взял Ряоби -день в проёбе девиз китайских плотников
@siamaklighvani3951
6 ай бұрын
I have a Bosch router and I experience that the RPM changes and not steady , slow , very slow normal , anyone have any idea on that highly appreciated.
@kingg283
2 ай бұрын
Did you solve your problem?
@siamaklighvani3951
2 ай бұрын
@@kingg283 not yet , but I will , because I need that tool , I bought one Chinese one less than 10 dollars , it was working well till it starts to kick back and the plastic cover was broken so I just use it as a spare parts .
@barkingspider4861
Жыл бұрын
Did not repair the armature.
@bobbauvian7700
Жыл бұрын
how about all the parking? aren't you going to fix that?
@modrribaz1691
Жыл бұрын
I think the problem was the type of spark, not sparking in general. At first, the sparking was coming from a specific place and there was also sound of electric shorting, meaning that is a short. At the end, the sparking was coming from rotation, which can be normal with brushed tools. I could be wrong thought.
@mathematiquesinformatique1423
Жыл бұрын
merci
@draganmilojevic3336
Жыл бұрын
Can you explain or show us how did you connect the wires to make that test device I see 4 wires but I don't get it what's what. Thanks in advance
@ZutiDIY
Жыл бұрын
Hi,its in series connection lamp.
@draganmilojevic3336
8 ай бұрын
Could you please send me a link I can't find it
@gregjohnson5194
3 күн бұрын
Title said how to find short? Did anybody learn how to find the short in this video? I didn’t…. 🥴
@Indiamaisabchorhai
3 ай бұрын
In india whenever electronics device get problem u go to technician. he will see u with device and laugh now i cut the goat 🐐. He make story device have that problem 7 days need to reapir that parts came from japan 😅and u have to pay advance 😂.if u pay advance than now u fucked up now another stories came in film he will make u left right months parcel came from japan 😅but in custom asking for tax have to pay 25percent 😅then now u have to gave money or ur advance is loss😂. He play minds games pressure u .😂😂😂😂😂. Every indian technician stories
@jesusnovato4764
5 ай бұрын
Se não tiver a cola atômica e nem a nuclear use grude 😅
@seymourwrasse3321
9 ай бұрын
Ryobi has the Arkansas warranty, if they break in to two pieces, you still own both of them
@laurentiat5312
9 ай бұрын
The "arcing saw" warranty?😊
@jaysagcal3681
5 ай бұрын
0:11 0:12
@bertdiver3708
Жыл бұрын
And I thought I ha a Big soldering iron! I get it. The big iron transfers the heat quickly so you dont melt the isolative rosin or winding coating.
@ebrahimmogarad2701
Жыл бұрын
سلام مهندس خسته نباشید به عنوان یک همکار از ایران خواستم بهت بگم ما تو ایران به این کاری که تو با آرمیچر کردی می گویم ان کار😂خب یا دوبارسیم پیچیش کن یا فقط کلکتور شو عوض کن یا کلا آرمیچر شو نو بنداز ترکار
@mybetterworks6918
Жыл бұрын
Its not short its cut.
@user-hh8ty8dw3h
2 жыл бұрын
Австралопитек I don't Wana comments
@normanbell236
Жыл бұрын
No fix there i see
@maslukhi6653
2 жыл бұрын
How to make test lamp?
@tttttttt8482
Жыл бұрын
Just two wires and lamp, 100 w
@04222797
Жыл бұрын
Not better after repair!
@salahennaffad7056
10 ай бұрын
Ilm
@jacquylenoir9097
2 жыл бұрын
Surtout, ne pas imiter, dangereux et idiot, ça n'a rien résolu
@gizmo1252000
4 ай бұрын
so after all that nonsense , it,s still sparking like a bitch . which means the armature is done ,and needs replacing .the only time sparks like that are ok ,is when a new set of brushes are put in ,and it quickly goes away ,as soon as the brushes bed in ,if it,s still sparking ,the armature is knackered ,just replace it .
@jamiematthews7079
Жыл бұрын
Get a bigger soldering iron and a multimeter might be an idea, rather buy another tool than go through all that palaver
@bryansoleta2101
2 жыл бұрын
How to make cummutator tester
@kitz8127
Жыл бұрын
Use growler
@user-mc9wv8lq5e
9 ай бұрын
Залепуха 😅
@santiagoacosta4437
8 ай бұрын
IT s not a repair
@jimmyamatthews5792
Ай бұрын
First of all, don't buy a ryobi brand, it's the worst machines ever made, I've had nothing but trouble from them, rather a Japanese make, like Makita etc.
@askerzeynal8638
2 жыл бұрын
C* C* C * C C * C* * C* C* C* C* SLAVA UKRAİNE! LET'S SUPPORT UKRAINE
@mirdallke2
2 жыл бұрын
precz z banderom przecz zukrainskim nazizmem -Wołyń 1943 pamientamy
Пікірлер: 132