The panel to locate the cruise control button in the correct place isn’t too expensive from Renault. This will need coded on the clocks and ECM. Best way is to use DDT4ALL and OBDlink sx cable.
@Markscampers
2 ай бұрын
I went for mounting it on the right because I didn't want any blanks on my dash lol
@paullynch9098
2 ай бұрын
Just to follow up on my last post, I was on a good road and just started pressing buttons and the cruise control works without any programming, still no light on the dash for cc but at least it works, also I mounted the switch to the opposite side so a word of caution to anyone doing the same thing the switch plug has 5 wires but 2 of them are the same colour 'white with black stripe'. I have a replacement binnacle ordered to change from mph to kmh, it's from a '17 plate so hopefully it will have a cc light
@Markscampers
12 күн бұрын
Thanks for the comment
@topgroover
7 ай бұрын
Great easy to follow no nonsense video. I've just acquired a Movano to convert without cruise control. So I will now be sorting that out. Thank you. 👍
@Markscampers
6 ай бұрын
Thanks for watching
@tamhamill5274
5 ай бұрын
Hi did you used renolink to code the Cruise control in thanks
@lawrencecrowe1214
Ай бұрын
If this is the same as my Vauxhall Vivaro, the cruise will work you just wont see anything on the dash. Which us exactly the same as using a third party cruise control. Its easy to live without the dash information.
@Markscampers
12 күн бұрын
Thanks for watching
@paullynch9098
2 ай бұрын
Good video. Trying to add cc to my vauxhall movano, got wheel and switch and same as your van all the wires and pedel switches are there but tried to get it coded and guy says cc is not on the module, did you have to add any fuses or relays?
@Markscampers
12 күн бұрын
No, not added any fuses or anything to mine
@jeremycanning8934
6 ай бұрын
great simple video. Did you get the cruise working? plus, was the reprogramming etc easy?
@Markscampers
2 ай бұрын
I had to divert my attention to getting the van usable so left programming the cruise control but will get onto it soon and update you.
@MultiOutdoorman
3 ай бұрын
Any tips on flashers going too fast after swapping over to led's Mark?
@Markscampers
3 ай бұрын
You don't have enough resistance. You need to either put a resistor in line or buy the led bulbs with them built in
@MultiOutdoorman
3 ай бұрын
Thanks Mark. Not enough current flowing with Leds. Ecu thinks a bulb has blown. Resistor acts as a controlled shortcircuit to allow more current to pass through the lamp circuit then?
@rambolane100
2 ай бұрын
hi did you manage to get cruise working and did you need to do anything else regards
@Markscampers
2 ай бұрын
I had to divert my attention to getting the van usable so left programming the cruise control but will get onto it soon and update you.
@MrGingergod123
3 ай бұрын
Hi Mark great video where and how can we get it coded once we have done these steps pal
@richards4456
2 ай бұрын
You need DDT4ALL and OBDlink SX cable. Needs to be activated in the clocks and ECM. There is tutorials on here showing it being done.
@Markscampers
2 ай бұрын
I had to divert my attention to getting the van usable so left programming the cruise control but will get onto it soon and update you.
@MultiOutdoorman
3 ай бұрын
Did you get it working?
@Markscampers
2 ай бұрын
I had to divert my attention to getting the van usable so left programming the cruise control but will get onto it soon and update you.
@cleansmartcleaningservices8157
3 ай бұрын
Hello did you get it all working
@Markscampers
2 ай бұрын
I had to divert my attention to getting the van usable so left programming the cruise control but will get onto it soon and update you.
Пікірлер: 27