No minutes long intro, no waffling, straight to the point. If only all KZitem tutorials were this good!
@jinkertsun
Жыл бұрын
Excellent video tutorial. I usually wash the door with warm soapy water which helps the new seal fit and make sure the thicker side of the seal faces outwards.
@charlesbrenan6269
Ай бұрын
Just tried this on my bank door frame. Nightmare! The old seal kept disintegrating into tiny bits and refused to come out of the groove. Must have been in there too long, I guess. You made it look so easy and it was probably is - I just took so long over it. But job done and the back door has a brand new seal round the frame! Many thanks for your very helpful vlog! 😊
@POUSEaroundtheHOUSE
28 күн бұрын
No problem 👍
@miranda-q6w
Жыл бұрын
What a champion 🥇 I have been searching for ages trying to find a vid to explain how to do this. Thank you 🙏
@POUSEaroundtheHOUSE
11 ай бұрын
Glad to help.
@tahirsharif9461
Ай бұрын
Done! Great video. Giving the door a wash with soapy water to ensure you get rid of the old rubber was also helpful. The outer edge isn’t equal, so one side of it is off centre more, so that needs to be the outer edge. Will check all my doors and windows now! Likely more swaps required.
@POUSEaroundtheHOUSE
28 күн бұрын
Good tips, thanks for the feedback 👍
@whitewittock
4 ай бұрын
Glad I found this video to know what to buy! Trying to join it at the bottom sounds like the most difficult place to me though
@antonyweaver357
8 ай бұрын
Great video! Excellent explanation, demonstration and a top job… Thank you. 🙏 👍👏
@POUSEaroundtheHOUSE
8 ай бұрын
Glad you found it useful.
@choperooni3388
6 ай бұрын
thanks very much for this, I've just replaced the seal on my son's house in Swansea. There is some play in the door though. When will you do a video on hinge adjustment please?
@bethevoice-gen1rev225
11 ай бұрын
My door is leaking, especially after this week's rain. Will have to replace the seal as I noticed upon investigation it has perished. I take it the same will apply to the door frame seal... Thanks for the vid.
@POUSEaroundtheHOUSE
11 ай бұрын
My seal was the same for the door and the frame. Maybe just check before you commit to doing it. Best of luck.
@bethevoice-gen1rev225
11 ай бұрын
@@POUSEaroundtheHOUSE Thanks...
@sheilaburns8163
2 жыл бұрын
Excellent you actually made this look easy and you have inspired me to have a go myself !!
@ashokgondalia9541
2 жыл бұрын
Absolutely amazing you're a lifesaver I seen this product but I don't know how to use it and now I know. You saved me a lot of time and money by this idea.,, thank you very much my friend
@rob91Harvey
4 ай бұрын
Purchased my first house last year and the back door, the rubber is pretty much disintegrated, just loose hanging strips😂. Looking forward to getting it sorted!
@POUSEaroundtheHOUSE
2 ай бұрын
Best of luck with it.
@AB-bq1vn
2 жыл бұрын
Thank you so much. We've got a lot of gaskets to replace. I didn't realise 2 gaskets on the door are needed. Thank you once again.
@marykane5276
3 жыл бұрын
Great video I have water coming in one of the corners of my door. Looks like the seal on the door frame is the problem but I would replace the seal on frame and door. Thanks to your video I now know what I need to get.
@POUSEaroundtheHOUSE
3 жыл бұрын
Best of luck with it Mary!
@legobatman8353
3 жыл бұрын
This has been on my to do list for ages. You've given me a bit of inspiration. Now just let me finish my coffee and I will 'think' about getting on with it.
@POUSEaroundtheHOUSE
3 жыл бұрын
Worryingly that's the attitude I'm beginning to adopt! I'll have nothing to film. Maybe 'Pouse the barrista'. Best of luck with it.
@legobatman8353
3 жыл бұрын
@@POUSEaroundtheHOUSE loved watching your uploads, keep it up fella.
@adam3rdcanvey
3 жыл бұрын
I've just done this on all my door and windows.. took ages 😂😂. Great vid though mate. My tip would be dont do it in the winter when the seals are rock hard. Or warm them up on a radiator first 😁
@POUSEaroundtheHOUSE
3 жыл бұрын
Good advice. My seal was OK but fair point, I probably should have made in the video.
@johnhearn5680
Жыл бұрын
Thanks for the video. Will have a go at a new door seal. Call out charge in Ascot is £100 plus, anything to do with doors or windows. Many thanks
@magill4046
3 жыл бұрын
Might have a crack at this, my door seals have definitely seen better days. Cheers Pouse 👍
@POUSEaroundtheHOUSE
3 жыл бұрын
25m was £16.99 I think. Made a real difference. Stop those horrible cold spots that attract condensation and mold around the door. Really easy, give it a go! Best of luck with it.
@ryanpratt9746
Жыл бұрын
Hi I can’t seem to find your video on how to adjust the hinge if the door is too tight after seal change (I already replaced my seal yesterday but door is too tight now ). Thanks for the video
@jethrodesilva7011
3 жыл бұрын
Had new exterior doors fitted last year so hopefully I won't need to do this procedure for a while, hopefully. Still, I found it very helpful and I imagine within my skill range. Thank you very much and when the time comes I hope I can remember your advice.
@POUSEaroundtheHOUSE
3 жыл бұрын
Please do come back and watch again when the time comes. Thanks for watching and for now I hope your door seals hold out!
@pauledwards9493
2 жыл бұрын
Christ this is hard work (getting it in the groove) but god it pays off!
@brikfiend
6 ай бұрын
Good Vid Ta . That door's Buzzin Mush !
@POUSEaroundtheHOUSE
6 ай бұрын
Ha ha. A lot of it is render from when house was done, the intention is to replace the door and this was just a temporary measure. But I agree, it is buzzing! Thanks for watching.
@waster1961
Жыл бұрын
I am looking to change seal on a double French door. Seems this video will help but I have a question - there is a panel on one of the doors which blocks access to the seal. How do I get around that?
@rebeccaemilie
2 жыл бұрын
Thanks so much for this I was thinking I’d have to get someone out but I’m gonna do it myself now thanks to your helpful video 😊
@KronenbourgLetsPlaysandReviews
3 жыл бұрын
Excellent, will look at doing mine, as when a heavy rain happens, it seeps in. Think its the actual door frame, so looks like the method is the same. One question, why start at the bottom? Should I not start at the top, as the rain using appears at the bottom, or is it just personal choice?
@POUSEaroundtheHOUSE
2 жыл бұрын
I have seen doors started at the top but I don't think it makes a difference either way as long as it's fitted well with no gap on the join. Thanks for watching 👍
@submergedcity9489
2 жыл бұрын
You start at the bottom so water drops there if it finds a way in and not at the top where it can drip around
@POUSEaroundtheHOUSE
2 жыл бұрын
@@submergedcity9489 well that was my thinking but I have seen seals fitted to new doors starting from the top. Thanks for your feedback 👍
@Dont-Evan-Bother
2 жыл бұрын
Thanks for the information. I had both my front and my back door replaced due to damages after an attempted break in and the "joiner" who fitted the doors had damaged the seals on top and underneath without saying a word and left after he was paid. I'm now stuck with 2 doors that don't keep the cold air out, but after this video I'm fairly confident about replacing the seals myself.
@POUSEaroundtheHOUSE
2 жыл бұрын
Hope it went well, thanks for watching 👍
@garranstvall1442
3 жыл бұрын
Great video Pouse... 👍🏾 looking forward to seeing the video on how to adjust doors or windows 👍🏾👍🏾
@POUSEaroundtheHOUSE
3 жыл бұрын
Thanks. I just have to find time the time to film them now! Thanks for watching.
@Cranstal
Жыл бұрын
Don't they recommend you start at the top of the door so that the seal at the bottom is a continuous strip and is weather tight?
@ferrets4
11 ай бұрын
Brilliant, you've given me the confidence to give it a go :)
@marialewis4913
Жыл бұрын
Brilliant video, thank you. Exactly what I was looking for.
@POUSEaroundtheHOUSE
Жыл бұрын
No problem.
@Fannybrew
3 жыл бұрын
Hi thanks for the video, would I need the same seal on the frames or will that be a different type? Thanks
@POUSEaroundtheHOUSE
3 жыл бұрын
I'm pretty sure it's the same, the seal is called universal door and window seal. Best of luck with it!
@glynwelshkarelian3489
Жыл бұрын
Good video. The only little thing is that you might want to run your finger around the old seal to find out where the original join was, and start from there. When I did it I was fairly sure I had enough seal but took the old out and replaced with new one side at a time. If I was short I could've left the last bit of old in.
@wendysides7081
Жыл бұрын
Great. Going to have a go. Thanks
@migi7787
3 жыл бұрын
Thanks, great advice. Would you be able to guide me on how to remove the old seal? from UPVC windows? It is sooo stuck due to age and dirt, that mere screw driver cannot remove it? Is there any special tool, or liquid, that can help with this please?
@POUSEaroundtheHOUSE
2 жыл бұрын
Before you tear it out just make sure the seal is one that can be removed as some are fixed to the door and can't be removed. If it can be removed then you could try using some white spirits on a cloth and a bit of elbow grease! Let me know how you get on. Best of luck.
@chriscopley3005
2 жыл бұрын
Thanks for the link. Saved me wasting time on Google then ordering the wrong thing 👍👍
@socialitarobotica
2 жыл бұрын
Do you happen to have a video about replacing the seals around the glass panels?
@POUSEaroundtheHOUSE
2 жыл бұрын
I don't sorry. Maybe one for the future!
@piamadison5539
3 жыл бұрын
Thank you for this video. My external seal is hanging off and needs replacing.
@POUSEaroundtheHOUSE
3 жыл бұрын
No problem. Glad to help.
@snowbind
5 ай бұрын
What an ace video. Thanks mate.
@rayw6928
2 жыл бұрын
Ray White.-Fitted the door seal ok with no problems.Fitted the frame seal and the door doesnt shut. The seal seems too thick to allow the door to shut --Help!. Does it need the frame seal as the water drains out along the lower section anyway?
@zeshankhaled6081
Жыл бұрын
No matter what I try I cannot get the old seal out. The sides lift up but the bit in the groove won't budge from anywhere! Have tried flat edge screwdriver, scraper, pliers but all I've done so far is tear the seal in multiple places :) any tips welcome!
@jessicawilliams4439
3 жыл бұрын
So useful! Do you have a video on replacing the metal strip on the floor? Mine has come completely off 😭
@POUSEaroundtheHOUSE
3 жыл бұрын
I don't sorry, maybe one for another video!
@bathfun
3 жыл бұрын
This is fantastic, my mum's pretty old door is drafty, so, thanks buddy
@POUSEaroundtheHOUSE
3 жыл бұрын
No problem, good luck with it 👍
@smellypunks
10 ай бұрын
Did you do the video with how to adjust the door? Not seeing on the channel.
@captainbimble
Жыл бұрын
Problem I have is when my door is fully opened there is only a very small gap between the top of the door and the ceiling. This means I can't see what I'm doing when at the top of the door. Can the door be easily removed from the frame so I can replace the seal then put the door back or would I be asking for trouble if I attempt to remove the door?
@CB27
Жыл бұрын
The seal on my frame has perished as well. Is it usually the same type of seal?
@POUSEaroundtheHOUSE
Жыл бұрын
Yes, you can use the same seal, just check the sizing as shown in the video. Best of luck with it.
@markgriffiths8027
Жыл бұрын
Great demonstration how to fit thanks and going to attempt mine tommorow, quick question though would you replace both seals as there is also one in the frame of the door?
@POUSEaroundtheHOUSE
Жыл бұрын
It's up to you, I only replaced one in the end as the fitting was tight. If you feel it needs it then go for both. Best of luck with it.
@markgriffiths8027
Жыл бұрын
@@POUSEaroundtheHOUSE Decided to do both turned into a bit of a nightmare as they were factory bonded in the corners, but with a few minor alterations and a lot of patience job done not drafts and much quieter 👍
@roxanascarlat6329
2 жыл бұрын
I have a question. The other seal (the one between the glass and the window frame) can be replaced? And if so what is that called, if it has a special name. Thx
@POUSEaroundtheHOUSE
2 жыл бұрын
It depends on the type of door. Most doors are made with the bespoke plastic inserts to fit the glass into place. You could try a local window company and see if they could provide one? Window and door seals are sometime referred to as gaskets which may help with your search. Best of luck.
@Indica_noon
2 жыл бұрын
Have you got any tips how to remove a super perished door seal? Like it’s falling to bits and hanging on by a thread in some/ most places :(
@POUSEaroundtheHOUSE
2 жыл бұрын
You could try turps or white spirits with a nail brush? Best of luck.
@funglam7395
Жыл бұрын
Mr Pouse. Love your videos man! This was so useful. Bought the same seal and your tips were greatly appreciated!!
@suelingchu4592
2 жыл бұрын
Awesome vid. Really informative and I will be looking through your other vids for inspiration. I'm ready to order seal to guve it a go but on inspection of my door I've found that the seal is the 'flipper' version. Is it possible to change it to the 'D' or 'P' shape? Thank you.
@gillianstubbs9935
6 ай бұрын
Brill! Going to have a go of replacing ours.
@joemorris1282
3 жыл бұрын
Love your vids Pouse, I did this on a window last year in the same way you did it, and now you've reminded me to do it with my front door, crackin!
@POUSEaroundtheHOUSE
3 жыл бұрын
Thanks for the feedback. It made a huge difference to my door. Best of luck with it!
@MonticArckeys
2 жыл бұрын
You make it look so easy. Just tried this for nearly an hour and can't get the new one to stay in at all
@POUSEaroundtheHOUSE
2 жыл бұрын
Are you sure it's the correct size? You have to get the first bit to bite then the rest will be forced into place but it does need a bit of elbow grease. Best of luck.
@peterthomas9632
Жыл бұрын
Is it the same procedure for the door frame it’s self ?
@cravader
Жыл бұрын
thanks so much - just about to do this myself!
@POUSEaroundtheHOUSE
Жыл бұрын
Hope it went well! Thanks for watching.
@shine5063
2 жыл бұрын
Can you please advice Which Side of the seal will be inside, Longer or shorter Side will face inside
@rmuttley5511
Жыл бұрын
Brill. Nice and easy to follow.
@kasianosowska7562
Жыл бұрын
Would you use the same seal for the frame, please?
@POUSEaroundtheHOUSE
Жыл бұрын
Yes you can as long as the frame has the same groove.
@donnabutler3800
2 жыл бұрын
Hiya, do you use the same seal for the door frame as the door? Ty. 😊
@POUSEaroundtheHOUSE
2 жыл бұрын
You can yes if it's the same fitting. Mine was. Best of luck with it.
@donnabutler3800
2 жыл бұрын
@@POUSEaroundtheHOUSE thank you.
@noral1960
Жыл бұрын
excellent video..thank you so much..
@notreallyhere1136
3 жыл бұрын
Thanks for this, definitely a job I need to do. And wasn’t sure where to start. Looking forward to the next video on how to adjust the door as well. The fit is really not tight
@POUSEaroundtheHOUSE
3 жыл бұрын
Thanks for the feedback Andre.
@wotcherfaz
2 жыл бұрын
It was a lot trickier to really bed the bead into the groove I found. It kept coming out while I was trying to continue further along. But perseverance pays off.. The door is tighter than before. I also notice that there are two grooves in the frame, but only one had been fitted with the seal... I guess fitting a seal to the other one will improve the insulation.
@POUSEaroundtheHOUSE
2 жыл бұрын
I guess you could try two seals if you want. it is tricky to bed in and requires a fair bit of force but worth it in the end. Thanks for watching 👍
@leoz235
3 жыл бұрын
Hi Pouse! Great video. You mentioned another video giving guidance on adjusting the hinges to close the gap? Where might I find it please? Thanks in advance.
@POUSEaroundtheHOUSE
3 жыл бұрын
I haven't done it yet! Hopefully soon. Thanks for watching.
@kymsmith5823
Жыл бұрын
How do you fix the rubber that's actually on the glass please? My pation windows is coming off and some missing
@gavpatterson1943
Жыл бұрын
What is the black seal called that goes around the exterior face of the window and is attached to the door. Mine has started to crack.
@pureblood1978x
3 жыл бұрын
So happy to see this video. Maybe customers won't keep asking me to do it. It's a horrible job on a full house.
@POUSEaroundtheHOUSE
3 жыл бұрын
Glad you enjoyed it. Thanks for watching!
@joebrennan.4389
3 жыл бұрын
Thanks Pousey, one of your best videos yet, very useful information. ..👍
@POUSEaroundtheHOUSE
3 жыл бұрын
Glad you enjoyed it. Thanks for watching!
@paulperrin4574
10 ай бұрын
Good stuff mate thank you..
@SD-gw5vm
Жыл бұрын
Lifesaver. Thank you so much
@sennysenny1925
2 жыл бұрын
Brilliant going to tackle this at weekend x
@sierradonaven6591
3 жыл бұрын
You always up my willingness to give it a try. Thank you.
@POUSEaroundtheHOUSE
3 жыл бұрын
Brilliant, give it a go...only if your door seals need changing of course! Thanks for watching.
@danward5607
3 жыл бұрын
Before people start ripping there door and windows seals out check if there what’s called Co extruded ,as most of the decent quality and newer profiles are pressed in on manufacturer and not designed to be removed , older door profile like the one in the video and cheap profiles like new builds use can often be removed
@POUSEaroundtheHOUSE
3 жыл бұрын
Thanks for the feedback Dan 👍
@stoneymaloney3457
8 ай бұрын
Boom great video no BS thank you
@POUSEaroundtheHOUSE
8 ай бұрын
Glad you enjoyed it
@paulwrite1405
9 ай бұрын
Good video well explains but d have put the join on the top
@gregorybolton6599
3 жыл бұрын
Great vid as usual very informative keep up the good work
@POUSEaroundtheHOUSE
3 жыл бұрын
Thank you!
@mikedolman7056
Жыл бұрын
Great video thanks
@POUSEaroundtheHOUSE
Жыл бұрын
No problem.
@niknoks7638
3 жыл бұрын
Your a bloody legend mate 👍👏
@POUSEaroundtheHOUSE
3 жыл бұрын
Thanks for the kind words!
@rehanamahmood123
2 жыл бұрын
So useful! Thank you for sharing.
@POUSEaroundtheHOUSE
2 жыл бұрын
No problem, thanks for watching 👍
@paulcowan3222
3 жыл бұрын
why is the join at the bottom of th door when I clean the road dust off the front door the water comes through the join. would it be better to have join at the top
@POUSEaroundtheHOUSE
3 жыл бұрын
You could put it at the top, no reason why not. I chose bottom as if it rains and water did drive in by seal I felt it'd be better to keep the continuous seal at the top. You could dab a bit of super glue or sealant on the join if it's a problem? Thanks for watching.
@julieandoliver1980
10 ай бұрын
But how do I know what thickness of seal I need not the arrow bit,I had some fitted by council and he said it was the only size he had on the van but could be bigger ??????
@farrokhfaramarzi
2 жыл бұрын
Very good, thank you.
@03133786
2 жыл бұрын
Great video! 👍
@POUSEaroundtheHOUSE
2 жыл бұрын
Thanks for the feedback 👍
@welshmanjasonpatrick8607
3 жыл бұрын
Very good tips on door frame
@POUSEaroundtheHOUSE
3 жыл бұрын
Glad you enjoyed it, thanks for watching.
@mishatomskovich7103
2 жыл бұрын
Fantastic video. May thanks...
@willcarter9168
3 жыл бұрын
Cheers for the video and the link on amazon! Spot on :)
@POUSEaroundtheHOUSE
3 жыл бұрын
No problem.
@robertdukes4420
Жыл бұрын
Losing my mind with this. Got the same seal as you and I start popping it in but by the time I get to the bottom of the edge the top has popped out. Tried rocking it into place but no dice. Managed one window but simply pushing it into the groove doesn’t work I had to spend hours messing about with it. Any guidance on what I’m doing wrong would be super helpful
@POUSEaroundtheHOUSE
Жыл бұрын
Hi Robert, the only thing I can think is maybe the seal isn't quite the right size? Let me know if you manged to do it and what the solution was. Best of luck with it.
@robertdukes4420
Жыл бұрын
@@POUSEaroundtheHOUSE appreciate the reply! I did eventually manage it yes thanks - issue i was having was just pressing the seal against the opening wasn't making it connect, i had to press right in the middle over the groove with the tip of my finger in order to get it to connect properly. Room feels much warmer already and hoping the whistling will stop when winds pick up again! Cheers
@philrichmond7567
3 жыл бұрын
Good to see you again.👍🏾
@POUSEaroundtheHOUSE
3 жыл бұрын
I'm still here.....just!!
@ratchriat1716
3 жыл бұрын
thanks for sharing this information with us found this video very informative and useful stay safe.
@POUSEaroundtheHOUSE
3 жыл бұрын
Thank you. Stay safe also and thanks for your continued support.
@stuartibbotson7179
3 жыл бұрын
really usefull thanks for doing this cracking video
@POUSEaroundtheHOUSE
2 жыл бұрын
No problem, thanks for watching 👍
@jons6125
3 жыл бұрын
I need the hinge adjustment video! Could drive a car through my gap the seal doesn’t even get close!
@POUSEaroundtheHOUSE
3 жыл бұрын
Maybe park the car in it? I'll see what I can do with the hinge video. Thanks for watching.
@monikag9081
2 жыл бұрын
my door doesn't seem to have a groove, the seal is just taped to the side. Is that just a type of door or the previous owners messed up with it? 🤨
@craigypd
11 ай бұрын
Good vid 👌
@POUSEaroundtheHOUSE
11 ай бұрын
Thank you!
@paulmarkham2197
Жыл бұрын
Cheers mate
@lewishowel4288
8 ай бұрын
does anyone have the link for the video about reducing gap when door is shut? driving me mad...lol
@duoadupa1195
2 жыл бұрын
You should start of the top of the door. And before put seal to hot water.
@sandocheese45
3 жыл бұрын
Nice one pouse, good job your tall, I'd need a ladder 😃👍
@POUSEaroundtheHOUSE
3 жыл бұрын
I did use a little help!! Thanks for watching.
@awantamta
10 ай бұрын
Great
@boxingday11
3 жыл бұрын
Good tips as usual 👍
@POUSEaroundtheHOUSE
3 жыл бұрын
Thanks!
@johnnymacf1
3 жыл бұрын
Nice one👍
@POUSEaroundtheHOUSE
3 жыл бұрын
No problem.
@MrFreddiew1
2 жыл бұрын
Clean the frame and seal groove first...
@charlesforeman9438
10 ай бұрын
I would have given the grove a good clean of dirt and mould before fitting the new seal.
Пікірлер: 188