Thanks! Finally found a video that showed me how to remove the casing. After this it was quite easy. I only used one screwdriver to loosen the case. Tip: at the position of the click-system just pull the case to the outside with the screwdriver. Thanks again for your helpfull video!👍
@MichaelMullan-e3x
2 ай бұрын
Thank you very much from one Irish man (living in Vienna)to another. This was the help I needed. This is a case of built-in obsolescence by Bosch and the door casing is constructed to make it as hard as possible for amateurs to dismantle. But gratefully you showed us how to do it. Thanks a lot!
@asturt
Ай бұрын
How to take the door apart was what I needed to know. I'm planning to fix a friends dryer door, and it's a very similar Bosch model. The catch on the door has snapped, and the part I need to replace is that whole inside part of the door. I've ordered the replacement, but I needed to know how I would get the thing apart to fix it. Thank you so much for posting this. 👍︎
@bootsowen
Ай бұрын
no problem, let me know how easy it was to fix
@KDParry-qb7jv
Ай бұрын
@@bootsowenhow do you remove the front panel on this washing machine, I have a newer version and it’s almost exactly the same as the one in the video and I need to replace the door seal as it’s full of black mould.
@xr8752
2 ай бұрын
Brilliant video! The whole snap thing does my head in. It always feels to me like the plastics will be weakened when you've had to prise them apart, and it annoys me no end that companies now seem to go out of their way to prevent competent DIYers from servicing their own appliances. Thanks so much for posting this!
@raphaelh.4526
2 ай бұрын
A quick advise for everyone who will need to remove the frame. Don’t lay the door on the floor like in the video because the snaps will snap back because of the weight of the door. Instead hold the door upright with one hand and pull back the white frame a bit and then losen all snaps with a screwdriver with the other hand, will take you one minute only and you will not scratch the door because you don’t need any force
@Patsy950
7 ай бұрын
You're a star! All other videos I've seen had doors with screws on the outside no good to me, my door is like yours, had no idea how to get into it! .. thanks so much for this video, much appreciated 👍
@daviditzcovitz89
11 ай бұрын
This video actually helped me a lot in getting mine fixed! It was the large black plastic surround I needed to replace as the hinge locating pin had snapped through it, making it drop and not sit right when open. I only needed 2 flathead screwdrivers to get this off though, one to act as a placeholder in opening the gap up and one to actually loosen the clips. Easy enough. Whole process took about 40 mins. Cheers!
@Dwaynepipe18-c1k
2 ай бұрын
Thanks so much, I was able to change it. Best wishes from Australia!
@peterburger2304
4 ай бұрын
Thanks a lot for the video. I also managed to fix my bosch-hinge! It looks like a common problem...😏
@dbull46
11 ай бұрын
Cracking video loads of clear detail. Could not of asked to find a better one. Thanks
@bootsowen
11 ай бұрын
Thanks, hopefully it helps you.
@kluminarysolar9522
2 ай бұрын
After 4 hours of searching, you saved my skin, thank you so much dude
@BiancaEsselman
2 ай бұрын
Thanks this is what i needed. As a woman i did it al by my self.
@wickwatts
Жыл бұрын
Brilliant! I don't think Id have been brave enough to unclip the white surround for fear of breaking it. Just fitted a replacement hinge in around 15 minutes. a little fiddly but great advice with multiple screwdrivers hold the clips.
@bootsowen
Жыл бұрын
It's nice to try these repairs yourself!
@WFVExclusiv
Жыл бұрын
Thank you, there was no one who took the video of the dismantling of the door, now there is. Now that I know how to remove the heat shield doors, I can remove them using a similar method.
@bootsowen
Жыл бұрын
It is tricky, but not too hard when you know how!
@WFVExclusiv
Жыл бұрын
@@bootsowen yes definitely, should we unscrew the door hinge to remove it? It shouldn't be obvious that it was disassembled because I don't want it to be out of warranty.
@andreachampion2471
7 ай бұрын
Wow…..thank goodness for this video. 60 F just changed my machines hinge 👏👏👏. Total cost $25NZ rather than paying a call out fee and parts and labour. Result 👍👍👍
@bootsowen
7 ай бұрын
cool, if it saved you money think about adding a tip through paypal or superthanks! cheers.
@joeking2730
Жыл бұрын
Your how-tos are very helpful, whenever I use them they always work
@abelvanwyk8872
2 ай бұрын
Thanx a million mate. The video really helped me and save me some cash. I'd cut some cardboard strips and placed it over the clips to get the outer ring off. Awesome video.
@laura6519
3 ай бұрын
Thanks so much for this! I've been looking everywhere to find out how to disassemble the parts of my Bosch Tumble Dryer door, which also has a broken hinge and no screws, like your washer. I was told I needed to order a new glass door which included the hinge. Sadly I've already placed the order, but at least this will mean I can take off the plastic front glass and ring from my old door without having to buy those too.
@edmundbrennan5334
Жыл бұрын
Great fix. Been trying to figure this door out for ages. It does actually seal even with a completely broken hinge by the way. I have been just shoving mine on for the last couple of months.
@Julie-hf7mo
9 ай бұрын
Mine has been working furniture for past year like this. However, today, water everywhere. Lesson learned and new hinge on order 😊
@Humppasonni1972
4 ай бұрын
Thanks for the video. Door hinge is now replaced and I saved at least 100€ for doing it myself.
@bootsowen
4 ай бұрын
Nice work! Think about a donation to the channel or becoming a member. Thanks
@synjhindb9951
8 ай бұрын
You legend. Managed to make a temp repair on a Siemens machine (same door) after watching this. You hero
@jpee300
5 ай бұрын
Thanks a lot for the vid! Saved me brute forcing or breaking the cover when removing it. Now just waiting for the new hinge to arrive. Keep up the good work.
@traffic-law
Жыл бұрын
I love watching instructional videos made by people who have no idea what they are doing.
@owenmurt
Жыл бұрын
Thanks lad. I had a fair idea what needed to be done, but I was shitting myself that I'd break the outer plastic ring. Done mine the exact same way as yours, even though its a different make. Thanks again
@dizzeerussell
Жыл бұрын
Awesome boots, I fixed mine tonight with your fantastic tutorial 😀
@seanolly478
4 ай бұрын
Thanks great video I was really worried about breaking the casing but this gave me the confidence to get it done
@BOMBON187
3 ай бұрын
Wow didnt even know Bosch made washing machines 😮
@thegoat949
19 күн бұрын
Great video repaired the door hinge following your video used some 6mm brass rod i had ,threaded it with a 6mm dye drilled the hinge block with a 5.5 mm drill and tapped the hole with a m6 tap screwed in and put a dab of threadlock on . Jobs a good un
@bootsowen
18 күн бұрын
This has to be better than before!
@imranimrantv2216
7 ай бұрын
THANKS BOSS I'VE JUST FIXED MY INNER PANEL WITH HELPING FROM YOUR VIDEO I APPRECIATE ❤
@wajidhussain9835
3 ай бұрын
Hi thank you i have seen your video then i have changed my washing machine hinges you have explain very well. Thanks
@Stilhi24
Жыл бұрын
Thank you for the video. I lost my hope and temper when trying to get that cover off but your video helped. I drilled 5mm hole in it and made 6mm screw thread in it. Then 6mm screw on and cutted the head off.
@amira.1093
11 ай бұрын
Did you do it on both sides? The plastic part and the hinge? Is it holding up?
@amira.1093
11 ай бұрын
I did the same as you suggested since pins are not as easy to find as screws (no intentions here:). I also got a no rust screw. About the opening part I found it more helpfull to use plastic credit card like to stick inside (also used some popsicle stick and plastic box cover) so I had quite a few and it is thinner than a screw driver and easier to stick many of those.
@patriciamarinvega1040
6 ай бұрын
Me has ayudado dos veces a arreglar mi lavadora con dos años de diferencia ❤
@danielhanley-thurkettle8904
Жыл бұрын
Well I hope you'll be able to fix it because I like watching your videos how do you fix stuff
@elainenichols7900
5 ай бұрын
Thank you for the video, my washer door is now fixed 👩🔧
@GeniusSL
Жыл бұрын
Great fix, cheap and fast!
@przemysawklimczak7692
3 ай бұрын
Thank you. It helped me a lot.
@bootsowen
3 ай бұрын
You're welcome!
@user-gf7sf4vz6f
Жыл бұрын
Thank you very much, thanks to the repair of 20€ I saved 600€. I only got it done thanks to your tutorial. Send me your Patreon link and I'll send you a tip.
@bootsowen
Жыл бұрын
Hi, thanks. did you send a paypal already? If so thanks!
@pampafons-ih8jf
Жыл бұрын
Thank you so much, I couldn't figure out where those screws were hidden
@darrenhyland2881
10 ай бұрын
Thanks for the help
@166Roberto
11 ай бұрын
I put the door on the carpet and pulled inelastic trim out with the tip of my fingers It popped out very easily
@willybarr3259
9 ай бұрын
Thank you from this!!
@jorgejorge2151
8 ай бұрын
The hinge broke in my machine as well (and, as I see, this happens quite often. Is zinc really suitable for this application?) The first thing I did was to try to fix it myself but ... no screws!, Thanks to your tutorial I saw the way how to do it (let me recommend chisels instead of screwdrivers, they are "stronger"). Luckily, the local branch office had the spare part and I picked it up myself. Finally, we were able to put our next laundry same day! Thanks🙂
@itsDragon_Star
6 ай бұрын
I have bought a spare part from internet but it turned out that it's too small, I couldn't close the door, so we just removed the broken knot from the plastic not, and we drill a little bit of hole, I inserted the broken knot half way in the plastic knot and we attached it in the hole that we drill, so now it holds. I just hope I could return the one that I ordered
@MrRujo
11 ай бұрын
Thanks for clear and usefull explanation to repair and fix it!
@bootsowen
11 ай бұрын
You're welcome!
@MrRujo
11 ай бұрын
Today I went to Praxis shop and buy a part of 6mm steel a € 2,50 and fix the broken part as you suggested in less an hour. The door is now woking as usual. No service costs a € 69,- and buy me a beer...😂
@bootsowen
11 ай бұрын
Cool. Thanks. PayPal link In description! Prost!
@zx8401ztv
Жыл бұрын
Thank you for repairing that bosch bootsowen :-D i bought an almost identical bosch serie 4 in 2018 and the only problem so far is the door switch/sensor plays up and i have to open and close the door a few times before it will start the wash. Not a bad machine otherwise :-D But the door may need a drilling later on ha ha :-D I had to turn off the beeping as it just annoying. I hope you havn't caught the new strain of covid, wear a mask if you go to supermarkets with lots of people around.
@bethcollins461
Жыл бұрын
Excellent video, big help.Thanks Boots
@KiM-og1pf
Жыл бұрын
Thank you for saving my headphones! 😊
@originalellamalacha
Жыл бұрын
Great video thanks, helped me out massively.
@aidanbrennan9989
Жыл бұрын
Great video, exactly the problem that i have
@kevinbeattie7595
Жыл бұрын
Worked a dream thank you
@robert3325
11 ай бұрын
Great tuition. Thanks for sharing.😅
@kekster11
Ай бұрын
Thanks Sir!!!
@bootsowen
Ай бұрын
Welcome!!
@huseyinaslan06
6 ай бұрын
THX FORM TURKEY👍👍🤲🤲🤲🇹🇷🇹🇷
@stufish4040
Жыл бұрын
Fantastic ! :)
@claudiahdasilva
11 ай бұрын
What torx screw driver is this ? T5?
@bootsowen
9 ай бұрын
Maybe t20
@tommyhanlon8012
Жыл бұрын
Good one.
@bootsowen
Жыл бұрын
I liked this fix. Was going to buy a part but couldn’t part with £10
@keithwilberforce
6 ай бұрын
Cheers fella £15.97 for new part and fixed new hinge to door, and diy is not me
@monkeyboythethird
Жыл бұрын
I am on my 3rd hinge broke in the exact place after one year sompart out of warranty - very frustrating as seems to be design/manufacturing fault in the parts - £13.95 is cheaper than buying a new washing machine but really Bosch should be covering the cost
@monkeyboythethird
Жыл бұрын
Oh and thanks for the video - very helpful - you feel like you are going to break the door prying it off - would be interested to hear how your repaired hinge is fairing !
@bootsowen
Жыл бұрын
Do you need to buy a new one or can you just mend the broken ones. I had a dryer once and I mended the door with a heavy duty house door hinge. Clumsy but didn’t break again.
@michaelvivian5076
Жыл бұрын
Anyone know what the plastic square part is called. We lost one during repair and I can't find a replacement
@bootsowen
Жыл бұрын
Where? Which part
@indesitlghotpointwashingma8305
Жыл бұрын
is this yours
@bootsowen
Жыл бұрын
It is now
@claudiahdasilva
11 ай бұрын
@@bootsowenWhat torx screw driver is this ? T5?
@jimthechemist
Жыл бұрын
Well done, most people would have paid the £11
@bootsowen
Жыл бұрын
Where are they now?
@AhsanKhan-fq2pq
Жыл бұрын
Thank you for your video lad, much appreciated Btw I love your fucking beard
Пікірлер: 92