This was very detailed and most importantly, shows how you put it back together afterwards! Thank you for sharing :)
@Shatanna
4 жыл бұрын
This video was awesome! Thank you for helping me complete my first equipment repair.
@joelarcoable1
11 ай бұрын
exelente no que nose puede claro que se puede en unos dias tengo que cambiarle lagrasa y engrane a una k5ss kitchanaid buen trabajo sra. la felisito like 244
@MissLove26
6 жыл бұрын
Thank you so much! Great video! Perfect angles!
@REMROB
5 жыл бұрын
Best How To Video On This Subject On KZitem! Thank You! WELL DONE !
@SiLoQuieroLoHago
5 жыл бұрын
Thank you!! I am glad you liked it!!
@timscat4evr
3 жыл бұрын
Thank you for making that look so easy... Very clear instructions thank you
@sweetmemories4448
3 жыл бұрын
I liked your video. I was thinking to buy a punch, but is expensive. That too I have to buy different sizes. You used a substitute, Allen wrench @ 1:14, 1:19, which I already have in many different sizes. Thanks for making a nice and clean video and sharing it. My old model Kenmore Elite stand mixer leaked in first 3 to 4 uses after buying aprox 7 yrs ago. It is not leaking any more, perhaps because the separated oil has already leaked out. After watching several KZitem videos, I was thinking to replace the o-ring on the upper portion of the spindle inside the gear chamber. It appears that just by replacing the grease, oil leak may stop. I already clicked thumbs up button.
@alnbravo3159
2 жыл бұрын
Thank you so much for a no nonsense video I did run into a couple of little problems getting the mixer part back on the piece where the beauty ring goes over I really wrestled with that a little bit but other than that everything went well thank you again
@SiLoQuieroLoHago
2 жыл бұрын
Hi Alan!! Welcome to my channel! It makes me very happy to know that my video helped you!! 😀
@lucianodestefano7714
4 жыл бұрын
Grazie senza tuo video non sarei riuscito a riparare kitchenaid. Ciao
@harrywetterskog4097
5 жыл бұрын
Found the video very informative. My mixer makes a squealing sound when you turn it on. Sounds like a bearing not inplace properly or something rubbing. The original owner bought the mixer probably 13 - 14 years ago and when this happened he just didn't use it. Hopefully it would be repairable.
@hpvc7665
6 жыл бұрын
Excellent video! Very clear and helpful.
@SiLoQuieroLoHago
6 жыл бұрын
I am glad you liked it! 😃
@showgirlsaroundtheworldada4484
4 жыл бұрын
The best vlog about this!
@383SS350
5 жыл бұрын
Were there any seals or gaskets that needed to be placed?
@72gunslinger
2 жыл бұрын
The stainless/chrome ring needs to be a seal just like a wheel bearing seal on a older car,truck or trailer
@lizzyann4
3 жыл бұрын
Thank you!!
@anazays66
4 жыл бұрын
Normally , how many years after purchase kitchen aid the leaking would happen?
@equams
4 жыл бұрын
I want to remove the retaining pin to replace the grease, but it would not come out, Please healp.
@showgirlsaroundtheworldada4484
4 жыл бұрын
Thanks!
@Herbert04
4 жыл бұрын
Beauty ring doesn't want to stay up. Keeps falling off. Any suggestions?
@aliciavogt1251
6 жыл бұрын
Thank so much for making this video..it was very helpful.... I just found a Kitchen Aid Artisan Mixer at Goodwill for $35 and from what I can tell, it leaks oil and #2 speed is a bit slower than normal (other speeds are fine).... things that I'm sure/hoping can be fixed!
@SiLoQuieroLoHago
6 жыл бұрын
That sounds like a great deal. Good luck with your project and glad to hear this video may help you! :)
@adasdown2earthessentials186
5 жыл бұрын
Yes,an easy way you can fix it,i did!! And no problems now. I pay 90 for mine, Check this guy videos. You will learn how to fix it in no time!!
@pozmarciv
Жыл бұрын
I have this exact problem.. great video .. did you change the gasket?
@SiLoQuieroLoHago
Жыл бұрын
Hi! Thank you for your comment. I didn’t change the gasket, I only replaced the grease. It’s been 4 years and it continues to working fine.
@pozmarciv
Жыл бұрын
@@SiLoQuieroLoHago Ok great.. Thank you for the video and response
@franzavolio
5 жыл бұрын
I'm having trouble trying to remove the pin! It is sticky! What can I do???
@SiLoQuieroLoHago
5 жыл бұрын
It may be stuck, so you will need to use a punch tool to force it out with the help of an small hammer to carefully hit the punch tool while some else hold the mixer for you. It may require to hit a little harder to get it out. You can see the process in the minute 1:10 on my video.
@Dorilana
3 жыл бұрын
I am having the same problem. I have tried everything. Did you manage to eventually get it out?
@tortask-cao4469
5 жыл бұрын
My friend, I want to repair my kitchenaid myself, but the safety pin in the planetarium does not come out, I don't know if it has rust, but I'm spoiling it with the hammer and it doesn't come out, what do I do? I am from Venezuela and I have not got a good technician and decided to do it myself. My machine does not work the speeds and drips the oil and I want to do what you did in the video. remove the electronic feet and take them to a technician to check them and see what they have. I tried to balance them on the speed card but I don't get any improvement.
@SiLoQuieroLoHago
5 жыл бұрын
Es difícil sacar el safety pin porque esta metido a presión. Si le das golpes firmes pero suave utilizando un martillo puedes sacarlo. Mi esposo me sostenía la batidora mientras yo le daba golpes con el martillo como muestro en el minuto 1:10.
@tortask-cao4469
5 жыл бұрын
@@SiLoQuieroLoHago Gracias amiga ya mi hermano lo saco costo mucho le dio de golpes, se maltrato un poco pero que creo asi lo volvere a colocar. Quiero repararla porque no consigo quien lo aga, vivo en Venezuela los talleres responsables de esa marca ya no existen, los respuestos los tienes que encargar. Una vez estaba batiendo y depronto bajo la velocidad y como que la fuerza, pense que eran las velocidades descontroladas y no! porque no la puedo volver a controlar por la tarjeta que esta atras con los tornillos. Dije que la voy a desarmar ver como estan los engranajes engrasarlos y mandar a probar las tarjetas electronicas que tiene.
@383SS350
5 жыл бұрын
Try spraying a little WD40, and letting it soak. Keep applying the WD40, while it soaks.
@xavifefi
6 жыл бұрын
Can i use graphitized grease ones i clean the old one ?
@SiLoQuieroLoHago
6 жыл бұрын
I used KitchenAid grease that is a food safe grease. In case of incidental food contact, must not cause any physiological hazard or affect the food’s odor and taste in any way. You can buy it on Amazon. Kitchenaid 0011665W4176597 Genuine Original Equipment Manufacturer (OEM) Part for Kitchenaid & Whirlpool www.amazon.com/dp/B00OSC174E/ref=cm_sw_r_cp_apu_X1ICBbJ45GH4K
@Dorilana
3 жыл бұрын
PLEASE HELP ME. I CAN'T GET THE PIN OUT TO REMOVE THE PLANETARY. I've used a punch and hammer, and then a bit from a screw driver, to better cover the overall size of the surface of the pin, and a hammer. I have even sprayed it with WD40 in hopes that some would leak between the pin and it's chamber. I wiggled the whole planetary in hopes of getting the WD40 in better. I've tried putting the mixer at every angle.... upright, upside down and on it's side. I've tried both sides of the pin. I've even had 2 other people try it ... but nothing is working! And the end of the pin, and area around the pin is taking a beating. 😢 Edit: Extra information about my model. It is an Artisan and does not have screws under the silver name band thingy.
@xopenex1
3 жыл бұрын
Make sure the punch is not to big to slip through the hole where the pin is housed. If you have been trying just one side--try the other side of the pin. Don't hold back on the your effort or force to move the pin out. Good luck
@jennitampa5026
6 жыл бұрын
What should I say???? Thanks
@farnorth13
4 жыл бұрын
how long before it starts to leak again ?
@farnorth13
4 жыл бұрын
@Merman I changed the grease in mine. I don't think it was used very much in it's life. It may also be older as I did not see a nylon gear....they all appeared to be metal.
@SiLoQuieroLoHago
4 жыл бұрын
Diane Cadeau Hi!! I made this video two years ago and I am currently using the mixer without any leak.
@alexandersimpson3638
3 жыл бұрын
Oil?
@SiLoQuieroLoHago
3 жыл бұрын
Yes, oil. When the grease inside the gearbox of a KitchenAid stand mixer separates, the liquid part of the grease can leak out of the mixer as an oil. The grease inside the mixer's gearbox can separate for several reasons; heat from overloading the mixer, not using the mixer often enough, and time are the most common reasons.
@alexandersimpson3638
3 жыл бұрын
@@SiLoQuieroLoHago I might use a neoprene gasket, should help with a little luck...
@WiSeNhEiMeR-1369
4 жыл бұрын
I did not SEE the promised KitchenAid GREASE information ... I would love to have the REAL stuff --- or a CHEAPER alternative
@SiLoQuieroLoHago
4 жыл бұрын
Dave Cooper www.amazon.com/dp/B0722VGTHJ/ref=cm_sw_r_cp_awdb_t1_pfcwEbM4R8HYC
@SelfEsteemArchitect
2 жыл бұрын
Step.one, dismantle the entire machine....
@dougjenkins5482
5 жыл бұрын
Cut the lame music.
@neely8607
5 жыл бұрын
Aww... Someone having a case of the Mondays? Poor little thing.
@farnorth13
4 жыл бұрын
Doug, just mute the sound if the music bothers you.....easy as pie.....instead of complaining.
@chinachew3376
4 жыл бұрын
🙉
@72gunslinger
2 жыл бұрын
The stainless/chrome ring needs to be a seal just like a wheel bearing seal on a older car,truck or trailer
Пікірлер: 54