!!!!WARNING!!!! Video does not show re-installing insulators on power regulator board!! Very important to isolate the resistor or else smoke signals will be made. It’s better to leave the board connected and remove the two screws holding the POWER IN connector. Then it will not be in the way.
@AudioPhool
Жыл бұрын
I was going to place the similar warning DONOT GROUND THE TRANSISTOR TO THE FRAME you will lose sound from both channels make sure you replace the clear plastic square that falls into your machine when you remove the screw and nut on that board IMPORTANT
@joeyiroc8184
Жыл бұрын
This was excellent. I couldn't move the little PCB in the rear, as it is held on one side by a very small nut, and could not get it removed. But everything else was great. Thank you for the video.
@splatlunch8812
10 ай бұрын
Well I was going to give it a try but im a little worried of messing something up. Its good to see that it may only takes about an hour so perhaps i will have a shop do it for me. A shop up the road is $85 an hour. plus the taxi to get it there and back lol. Great video ,almost good enough for me to follow along with you but as someone pointed out there is a part perhaps missing. I wish it were as easy as spraying alcohol and adding oil.
@rickallen8158
Ай бұрын
Not criticizing your job, you did good showing what has to done, oil is ok on the capstan and pinch roller, but grease is best to lube the pivot for the pinch roller mechanism, that is what teac used from the factory but today there is much better grease that will not dry up and become sticky, Krytox is a good choice, use it once and you'll never have to do it again,,,
@rpk5568
Жыл бұрын
Novel approach, removing the two screws instead of removing the solenoid. Was looking to see how you dealt with the pressure spring that linked the solenoid plunger to the pivoting arm that you removed that was held on with two screws. You didn't show taking those out or putting them back in, must have been a bitch, but without that critical step this how to is incomplete. I assume you put the transistor insulator back on the voltage regulator board that is mounted on the back of the unit. That is used for the bias oscillator. A note on cleaning of pinch rollers and handling of belts. If you don't have proper rubber cleaning chemicals then water is recommended and skin oils begin the deterioration of rubber belts so avoid handling then. But there appear to be dozens of opinions on this subject, but then I have bottles of Teac rubber cleaner. There's lots of reading material on this subject.
@basspig
7 ай бұрын
I'm working on a A3340S where the pinch roller solenoid won't even try to engage. The mechanism is free to move, but the solenoid is only getting 7.6 VDC and not strong enough to overcome the spring loading that pulls the roller away when stopping the tape. I tried to pull a schematic off hifiengine, but their site is giving a 500 error when I hit download. Is that solenoid powered by 12 or 24 VDC? I really need a schematic to trace where the power comes from and why that circuit is soft.
@axelthefoxytechworld8024
7 ай бұрын
it could be 12v or 24 volt either 7.6vdc sounds low to me likely the powersupply needs recaped ive never worked on that nore have i ever had that problem
@basspig
7 ай бұрын
@@axelthefoxytechworld8024 Ripple was my first thought. But there is negligable ripple across the solenoid. I finally procured a schematic and it is more complex than I expected. This solenoid may be in series with diodes and other solenoids depending on the state of various relays. Ugh. But thanks for confirming the voltage should be higher.
@stevenhoelderich9490
2 жыл бұрын
Hello,you need to, replace you take up Reel, brake then, it will stop, spilling the Tape.
@axelthefoxytechworld8024
2 жыл бұрын
The reason it did that is cause the pinch roller wouldn't engage so I had to do it manually
@ChrisAtterson
9 ай бұрын
it looks new
@borysandreyev9717
2 жыл бұрын
Very useful detailed guide
@JamesE707
2 жыл бұрын
During FF/RW, is sounds as if the tape is very close to the playback head? I wonder if the tape lifter can be raised a little more?
@Poppinwheeeeellllllieeeeez
Жыл бұрын
I just flush with 99.9 anhydrous IPA to flush old grease into a cloth. Same with the solenoid. Add oil. Done.
@King_Colombia_Inc
Жыл бұрын
37:28
@ДмитрийИванов-к6и8с
7 ай бұрын
Вот это настоящий ремонт👍😊😊 КАКОЕ СЧАСТЬЕ БЫТЬ МОЛОДЫМ😊😊😊
@JamesE707
2 жыл бұрын
This is a game of patience, and learning (to a point) on the job. That's some fan!, on what seems to be the main motor!
@jamilmohammed7817
Жыл бұрын
I like the blue reel you have on the player will you like to exchange I will like to have it.
@axelthefoxytechworld8024
Жыл бұрын
sorry no
@SDsailor7
2 жыл бұрын
Do you know how to install a computer socket for the power cord? Mine is missing the power cord and i want to install a computer socket so i an use one of those power cords. Thank you
@SDsailor7
2 жыл бұрын
So you don't know how that is done?
@duncoyaomean6687
Жыл бұрын
I’m sending my 4010sl over to you for the same thing. Think I’ll just spray lube it 🤷♂️ 🤦♂️
@jamilmohammed7817
Жыл бұрын
Good job
@Treepadawan
2 жыл бұрын
Hey I just followed this tutorial and my teac and now smoking fuses in the top right and the play button now does not work at all
@axelthefoxytechworld8024
2 жыл бұрын
idk why it would do that you prbaly didnt put it together right if anything could be bad caps finaly leting out the ghost an yeah that happened to me to the micro switches on these the plastic is geting brittle so i had to replace my play microswitch
@Treepadawan
2 жыл бұрын
Where is the microswitch located?
@Treepadawan
2 жыл бұрын
I think my most of my capacitors are fine it’s just a specific spot smoking
@Treepadawan
2 жыл бұрын
Not sure where to go from here but I believe I found both insulations I believe for the transistor plate which I think is the issue for the smoking at least
@axelthefoxytechworld8024
2 жыл бұрын
@@Treepadawan yeah that transistor needs it plastic insulator peice the metal of it canot touch ground
@budokarate6212
Жыл бұрын
What’s the best type of oil to use ? Great video !
@axelthefoxytechworld8024
Жыл бұрын
3-in-one oil or zoom spout if you want the best oil there is thats what i used on this im glad you liked it
@AudioPhool
Жыл бұрын
sewing machine oil its cheap and it works very well works good on the motors so fill them up
@SlyTheFloof
2 жыл бұрын
lol
@Mark-kq9ur
11 ай бұрын
Odd, you cleaned the old grease from the pinch roller assembly, but didn't re lubricate it before assembly
Пікірлер: 40