Functionally operates just as it should kzitem.infoUgkxiiMg_x4gIWeXMWfBnDdRnME4qJUAva4w holds pressure perfectly when not in use. Glad one of the other reviews pointed out that the bottom pressure release valve was open; thought it was defective at first.
@tplcarndt6937
4 жыл бұрын
Thanks to your video I fixed mine in 15 minutes with a sheet of gasket material.You are a real mechanic.Thanks again.
@daniatto5591
4 жыл бұрын
Thank you so much! I just tried this method using a milk carton as the material and it worked like a charm. Thank you!!!!!!!!
@mikelane9608
4 жыл бұрын
I got tired of working around an older pancake compressor that shot craps three years ago. Yesterday I watched six Utube videos on how to fix a compressor that wouldn’t pump up to pressure. It was your video that helped me repair my compressor!! GREAT JOB ARTURO! Thanks!!
@impossible98123
5 жыл бұрын
Thanks for the video. I watched it after my compressor had problems holding air. I took mine apart, had the same split in the gasket in the center and went to an AutoParts store and paid $8 for gasket material (1/16") oil, gas, water and cut a new one using the old as a template (but I did it on a solid surface). Put it back together and went from 40psi and running forever to 120psi, back to normal. Thanks for the idea!
@kennethrichie9656
5 жыл бұрын
You just taught this old man something new. Thanks
@ballentine52jb
6 жыл бұрын
Just wanted to thank you for your video... A friend give me a air compressor. I went and bought hoses and all for it just to find out that it wasn't pumping air. You had the only video that addressed my problem and it worked!!!..... Thanks again for your video and all your help
@stephenpagliaro7063
4 жыл бұрын
Thanks for tip, never thought I'd turn an old pizza box into a compressor gasket and get it back up and running! That's exactly what the problem was. Very Helpful Video!
@MrLucifuge1973
4 жыл бұрын
Great video sir. Couple suggestions. If you cut your cardboard, say an inch bigger then original gasket and reinstall the head it'll give you a perfect impression of the gasket to cut out. You can just use a pencil to knock out the holes for the screws or just take an erasable marker and paint/color the bottom of the screw. With the cardboard in place an the valve cover in the right place press the painted bolt into the screw hole leaving an ink impression for each screw location. Remove the valve head cut out the screw holes and reinstall the head with the holes lined up. Screw each bolt in a few turns on the valve cover in order to make the gasket outline impression. Remove bolts and cut out your "new" gasket. Also if you use the same marker to color in/paint the valve cover, you can quickly press the valve cover on a piece of cardboard and it will leave an perfect impression of the gasket. Lastly, I believe gasket maker is only 7$. Lmao. Kind regards V
@lilpep07
Жыл бұрын
!
@edgray4635
4 жыл бұрын
I used Arturo's technique but without the care and patience he demonstrated. Still worked great for me!
@gerrynoelatanacio
4 жыл бұрын
Been looking and searching all over KZitem and other sites with the same problem. I haven't tried it yet but will do it right away next day. Hope it works out the same as yours. TIA 🤗🤗🤗
@tedjordan7567
6 жыл бұрын
Gracias Arturo! Your fix was exactly what mine needed. Thanks a lot!
@Anonymous-it5jw
6 жыл бұрын
Very helpful! Thanks for showing us how to do this the Old School way.
@freddysamson1
6 жыл бұрын
A really good gasket material for this or even a small gas engine is a milk carton not jug carton the coating when compressed stands in for sealant and works great.
@rgruenhaus
5 жыл бұрын
I guess you mean like a half and half container?
@apatel7787
2 жыл бұрын
Excellent idea. Thanks.
@ogbobbye
3 жыл бұрын
that is called peening a gasket because it is usually done using a small ball peen hammer. that is why old timers use to call ball peen hammers a plumbers hammer. don't do it now days due to it cost more to pay someone to do that than to just buy a gasket. it is a skill to remember if you are ever in need of a gasket in a emergency. thanks for sharing the video
@FrancisDumont-g4u
10 ай бұрын
Thank you for your help... you are so easy to follow as you explain what you are doing Thank You
@KC3VDU_Radio
3 жыл бұрын
I had the same problem, and that fix worked! Thank you!!!!
@budshepherd9893
2 жыл бұрын
thank you for taking your valuable time to educate us in this video.... you should be a teacher.. you showed us in detail and I thank you for this video...your new friend, Buddy S.
@arturoramirez907
2 жыл бұрын
Thank you so much for your comment and also I glad to be able for helping more people with the same issue thanks again God bless you 🙏
@gregtaylor6146
3 жыл бұрын
Thank you for sharing your knowledge Sir, count mine another one saved from the dumpster!
@MsNailgun
3 жыл бұрын
Great freaking video. Got the same unit with the same problem. Gonna give it a shot. Thank you.
@barryallenflash1
3 жыл бұрын
When you started making the gasket, I was thinking...hmmm...we used to do that in the Army. WOW! I have a Campbell Hausfeld and has the same issue, gonna try this and see if it works. I'll let ya know!
@arturoramirez907
3 жыл бұрын
Hey great hopefully it will be fixed
@richardsmith184
2 жыл бұрын
Thanks for a great fix . You my Hero of the Day!.
@brianomalley4101
4 жыл бұрын
Thanks for the video!!! I had the same problem. Gasket was no good. This fixed my compressor, runs right up to 125psi now
@edgardomatos6923
Ай бұрын
I'm building pressure , but when I put the hose to the air valve to fill tires or ball . I loose pressure .. weird! thanks for making this video . nothing g wrong with old school. that's sometimes the best way
@BigGreenJohnny
5 жыл бұрын
Thanks Arturo! I had the same problem and same compressor. I had no idea it would be this simple. Easy fix using an orange juice carton, will probably be buying an actual gasket if it breaks again.
@arturoramirez907
5 жыл бұрын
Hi I so glad to hear that also if you want to made a great gasket your self just get the material in the Auto parts I did it myself and replace is a bag with different sizes I buy it from Auto zone God bless you Arturo
@renatoruiz3392
Жыл бұрын
Muy chingon tu video Arturo me sirvió bastante., Muchas gracias carnal🤙🏻🤙🏻🤙🏻🤙🏻
@rosolion
3 жыл бұрын
Arturo gracias, con este video pude arreglar mi compresor.
@tawelfryn
4 жыл бұрын
Thankyou, slightly different model, but same principal, works a treat now!
@31acruz
Жыл бұрын
Good job ! a sheet of gaket is about $6 but cardboard will do in a pinch until one gets to the store. well done!
@frankolay3426
4 жыл бұрын
same thing fixed the gasket working now thank you.
@bubbabee1475
2 жыл бұрын
Great job Arturo, u saved me a lot of money 👍🏼
@golf-n-guns
2 жыл бұрын
My Harbor Freight 94734 had the same problem. Cut out a new one out of Fel-Pro 3075 and works like new again. Thanks.
@timothydean
4 жыл бұрын
God bless you that really helped me cause mine was doing the same thing!. thank you mister
@arturoramirez907
4 жыл бұрын
Thank you Mr Tim God bless you as well 🙏 and I glad the video help you out.
@charritolopez8223
4 жыл бұрын
@@arturoramirez907 se podra usar un tubo de bicicleta para aser un empaque
@georgiospantelakis7010
5 жыл бұрын
Had the same problem... solved temporary with a fat piece of paper taken from a shoe box. I will buy a proper gasket sheet and make a new gasket. Thanks for the video.
@MISTAMUSIK
4 жыл бұрын
Me personally I would try this but I would also use a silicon gasket maker for cars! It would be stronger and you may not need to replace for a long time or maybe never!! I may also use real gasket material and also the silicone gasket maker!!
@_RocketRooster
3 жыл бұрын
If you use silicon gasket maker the silicon will squeeze out inside the head when you tighten down the head bolts and when you start it up a piece of silicon will most likely break off and lodge in the reed valve and you'll be scraping gasket maker off the head when you go to repair it for the second time. Gasket making material from the parts store and making a copy of the old gasket is a much better plain.
@jeffpomeroy5070
4 жыл бұрын
I would use a paper punch for the holes. Instead of drilling them. Nice work.
@bobgreen3116
3 жыл бұрын
Thank you so much. Great information. Thank you for posting this video. 👍👍
@klkincaid6161
6 жыл бұрын
Bien Hecho fantástico! El video perfecto, sus instrucciones detalladas es la manera más fácil de seguir cada paso! Magnifico mi amigo! Gracias
@joesmith-wc5qh
5 жыл бұрын
Arturo that was excellent man thank you for taking the time to post this video. Hopefully the problem with the one I found is the same issue. Thank you again well done amigo.
@tomwarren5258
4 ай бұрын
Fantastic thank you I learned something new every day
@jamesmana5247
4 жыл бұрын
You did an excellent job. LOL I thought you might buy the gasket but they are a set and you only need one. WTF. I will have more work to do to make mine because I could not save the old gasket. That's alright as I have made hundreds in the paste. Good job
@jaimecortes1608
Жыл бұрын
I would just trace around the old gasket with a pencil since it's in good condition. Then use a ruler to trace the missing piece of the gasket. But great diy fix video. 👍
@natnaeltmariam4872
3 жыл бұрын
Nice job bro. If you use wood drill bit, drilling the hole would be easier.
@DUCERS3
4 жыл бұрын
Gracias Arturo! Saludos
@da1cru1
6 жыл бұрын
what make/model compressor is this? I have an OLD Sears Craftsman Tankless compressor that does not have a screw in output, and no filter! they have a weird shaped gasket that looks similar to an arch that fits in a slot that takes up most of the head and slightly into the plate that goes over the alum output tube! I've been searching for a replacement head that matches in size,etc.. but also has threaded output... Any help be appreciated!!!
@redpanda2401
2 жыл бұрын
Awesome, great vid Mr Ramirez !
@LASTSAGI888
4 жыл бұрын
You just put a thin coat of oil on block then stamp it onto cardboard then outline cut and walah
@thearrow5793
6 жыл бұрын
Good job man.....keep going... thanks...
@johndaly9843
Жыл бұрын
Thank you. Worked pefectly !!
@thomaslenton2133
4 жыл бұрын
Thank you! I'm hoping this is why my compressor isn't building up pressure and leaking as soon as I turn it off.
@Chriscaseyartist
Жыл бұрын
So clever! Thank you for the video!
@amyromus6210
3 жыл бұрын
At first I thought this is never going to work i tried it and believe it or not it worked!!!
@johnabalos1455
4 жыл бұрын
Old school is GREAT!!!!!!!
@aidancoughlan8746
3 жыл бұрын
Must try that think I got the same problem with mine great video thanks for putting it up
@arturoramirez907
3 жыл бұрын
I'm so glad you like it and hopefully everything goes well for you too and also get your fix it thank you
@mikemichael8683
5 жыл бұрын
Very good job!
@ronsbeerreviewstools4361
5 жыл бұрын
Arturo, good fix, this is a good informative video. Thumbs up & I subbed.
@l.a.raustadt518
4 жыл бұрын
More fun to watch than the impeachment bull shitio! Bravo Arturo!
@chrissilliker8633
4 жыл бұрын
Go Trump
@jvcovers1003
14 күн бұрын
Thanks bro, I'll try mine.
@kenday7942
11 ай бұрын
I am totally surprised that cardboard will work as a gasket material. How long does that last? I think I would take Arturo‘s suggestion to use regular gasket material and do everything else pretty much the same. Reading some of the other comments other people have had success using cardboard. Totally surprising!
@rgruenhaus
5 жыл бұрын
Very similar to mine and it doesn't seem to have any filters that can clog and it was all of a sudden, so this must be the same problem with mine. Would have helped if you showed it not building pressure before instead of just telling us, but you got it working as expected. What do you think caused the gasket to break down? Thanks for showing your repair. Where can we buy that gasket?
@arturoramirez907
5 жыл бұрын
Hi I just checked your message well the gasket over the time is going to get damage because the compression and the heat but you can probably find out a new one online or buy the material and made it your self that's what I did
@badtoro
6 ай бұрын
neat but wouldnt the heat be a concern for that paper to ignite?
@jamesrooney7689
5 жыл бұрын
your a good man thank you
@mrpeterpan4202
5 жыл бұрын
Good job.......Thanks for the video!!!
@gergemall
6 жыл бұрын
Great job. Thank you
@rumsiker
Жыл бұрын
WHAT IS WRONG WITH USING THE OLD GASKET AS A TEMPLATE, AND THE CENTER MARK EACH START AND USE A STRAIGHT ADAGE AND DRAW YOUR LINE, THE HOLS CAN USE A PAPER PAUNCH OR A SMALL SOCKET
@bradenharwood
2 жыл бұрын
Dude, thank you.
@rgruenhaus
2 жыл бұрын
What was the model number of that compressor and did you check the price of the gasket?
@joedegorostiza8305
5 жыл бұрын
I like your style - "fix without spending anything and to do least as possible work".
@thansoe9207
4 жыл бұрын
thank you very much for sharing.
@airwolf08
5 жыл бұрын
Very good video
@osirisone6019
Жыл бұрын
Muchos gracias
@nickblosser
3 жыл бұрын
Great job G!!!
@monkeyking-self-proclaimed7050
Ай бұрын
I bought a compressor from some guy. On the way to pickup the compressor, he told me it's not work and decided to give me the compressor for free. I came home plugged it in and realized that he just didn't know how to close the valve.
@naleenemb5232
2 жыл бұрын
Thanks for you !
@timmitchell4633
5 жыл бұрын
Great video, I have a "brand new", old Craftsman 15362 Air Compressor/ Direct Oil Lubricated - Cast Iron Cylinder, [135 PSI max., 3.7 SCFM @ 40 psi, 2.4 SCFM @ 90 psi, 1.0 HP 3 Gallons]; right out the box malfunction during the initial 'Start up" mild run, break-in procedure. Oil started leaking from the system and it wouldn't build pressure. I checked the fluid bulb, still contained fluid, tightened the bolts down, tried it the pump again, ...."No joy" then turned it off and threw in the back of the garage for ..... LATER. What should I do to fix/ repair for use? Thanks in advance
@arturoramirez907
5 жыл бұрын
Hi sorry for your bad experience with your air compressor well as far I hope it is possible a different things but you don't give up I not really an expert but just checking the oil level and gasket,the air pressure valve and final opened and you will be able to found the problem that's what I did my best wishes for you and your project God bless you have a great day.
@shanespence4063
3 жыл бұрын
Thanks for the video
@arturoramirez907
3 жыл бұрын
I'm so glad this info was helpful for you and also get your fix
@GraveCareMaintenanceServices
5 жыл бұрын
good video, but instead of using a Stanley knife / blade to cut out the gasket, why not puncture a hole in each of the segments that need cut out and just use scissors ? less chance of the knife / blade slipping and either cutting yourself or damaging your gasket.
@kcdiazWTV
3 жыл бұрын
Yup. This worked for me.
@coreydrakes6996
6 жыл бұрын
Perfect. Thanks
@leehelppie4544
3 жыл бұрын
great job!
@billvakras8272
Жыл бұрын
Old air compressors are like ticking time bombs - you never know when they will go off. It's not a good idea to have a bomb near you... that's why you never repair an airframe older than 10 years. safety first
@MidniteClubII
2 жыл бұрын
Senyor Arturo, why didnt you just take the old gasket and outline the gasket on the piece of cardboard?... My Stepfather used your method with the wrench when he didnt have a gasket to outline. Anyway. Thanks for sharing. :)
@jonboy6920
5 жыл бұрын
Great job there my friend !!!
@donlum9128
2 жыл бұрын
Thanks, old school cool
@cjoakman7715
4 жыл бұрын
I also make gaskets like this....sort of. Instead of tapping on the cardboard, I use the curved part of the wrench and press down against the cardboard and then rub it back and forth across the surface, pressing down the whole time and paying attention to where the bolt holes, ports, or whatever are on the head or whatever you are making the gasket for. Also, you HAVE to hold the piece of cardboard or gasket material perfectly still. Don't let it move at all or you will have bad results.
@jeffreymeeder372
5 жыл бұрын
My compressor wouldn't get above 50 lbs. This is exactly what was wrong with it. The head bolts had loosened after 10 years and the gasket failed in the same place
@icenesiswayons9962
5 жыл бұрын
@Jeffrey meeder if you the gasket didn't fix yours, it most likely the check valve on the tank!
@ShawnMtz_78
4 жыл бұрын
Cool...old school...my question is, would moisture damage your diy gasket?...
@sknerl
Жыл бұрын
I usually add gasket maker or oil to the cardboard. It’s a pretty common method to make gasket. I have sheets of gasket material, but usually can’t find it when I need it. Cereal boxes, and such make decent gaskets. I toss material in my shop for when this happens. I’d guess 70% of gaskets are made like this as most who replace these are pretty handy.
@cedricjones5798
5 жыл бұрын
I have a craftsman compressor what is the black knob for on it under the red knob it was given to me so trying to figure out how to regulate air in tank for pressurized tank that I use. It has a big red knob & black know under it any help is greatly appreciated.
@arturoramirez907
5 жыл бұрын
Hi yeah that's the pressure control know when you moved keep eye on the Gage control and you will see how much you are adjusting just don't go over 125ps
@cedricjones5798
5 жыл бұрын
@@arturoramirez907 which knob the black one or red one. The red us on top & black at the bottom. I know the red one. So when it to pressure I want then turn black knob to lock it there? Is that for tank or out going pressure? It keeps firing up all the time.
@w4st3lander
4 жыл бұрын
Plz don t use metal to remove little bits of gasket beacuse you will scratch the surface and that will make a leak
@braxtonellison1349
Жыл бұрын
Ok primo😊 heck yeah I got rubber flashing i can make a gasket out of... awesome video
@jessicakline2661
5 жыл бұрын
What's that black plastic/ rubber bulb thing do on the end of the top of the case has working on mines missing mine and trying to figure out something I could fab up to replace it
@rikovasquez693
5 жыл бұрын
That’s your oil fill/breather cap.
@DogDaze66
2 жыл бұрын
How much oil does it require ? I’ve the same one but bought it with no manual
@arturoramirez907
2 жыл бұрын
To be honest I don't ever put oil on my so I don't know how much it will take it maybe check out online hopefully you can get the info
@ArmandoRodriguez-bq6pt
4 жыл бұрын
Hola buenos días amigo tengo un compresor igualito a ese mi pregunta es no carga ya cambié empaques así como tú lo hiciste y no avienta nada de aire por la válvula de drenar espero tu respuesta y muchas gracias
@JoseRamirez-px3uq
2 жыл бұрын
Thanks Arturo for cheering this video !
@impactajuvenile
5 жыл бұрын
Repair shop would’ve charged like $60-100.00 for that repair probably???
@MiKa-fu2wi
5 жыл бұрын
yeep, and they woulda used cardboard too lmao
@shimanegabrielmolao2372
5 жыл бұрын
Good job
@jesusescobar435
2 жыл бұрын
Este compa si hubiese nacido antes del accidente del transbordador challenger, hubiese Salvado el equipo y los astronautas. (Porque fue in gasket el que hizo explorer al challenger que no? ) and also free advertisement for DEWALT.
@alijuman6172
5 жыл бұрын
Thx man
@NissanAltima2005
5 жыл бұрын
Good job
@fleaniswerkhardt4647
6 жыл бұрын
The air compressor I was given recently the same problem - so this video is really helpful. It's slightly different than the one in the video but similar in many other ways. The head is identical . I pulled the head off today and saw it had a metal gasket. The thing I noticed was that in this video - at 2:40 you mention 2 steel plates. What do they do? They look important. Are they simple valves of some sort? When I took the head off the compressor I have - there was only 1 of these small plates in the head. The guy who gave me this compressor must have taken the head off - and lost one of these - because there was only 1 of them. So - where do I get them from ?
@tommiller6580
5 жыл бұрын
There are called reed valves, one is suction, one is discharge, Harbor Freight carries them and other suppliers.
@bradpayn8058
4 жыл бұрын
Now I've got my work cut out for me. A year or so ago, I moved to a house with a small shop behind it. The people who lived here before left three small compressors behind (he was a roofer I hear). I already had a little pancake compressor that still works fine. All of those other three run good but don't build air. They've been here a year and nobody came looking yet, so I guess they are mine. One is a Craftsman, just like yours - I guess tomorrow I'll start with it first, and see what I can see in there. Then move onto the others. On of the others is a brand I never heard of, Mountain something or other - nothing comes on the computer, for it, and the other has no brand markings at all. Neither look that old though, but I never got in them, figured I didn't know where to get brand specific parts. At least now I know how to make gaskets - I'm sure I saw sheets of gasket material cheap at the parts store though. It looks like cardboard lol. Good video.
Пікірлер: 209