I thought about doing it like this but didn't know what to use for a mold. THANKS.
@RussM
11 ай бұрын
1/2 inch pvc collar works
@MotersickleBum
11 ай бұрын
@@RussM Thanks....that's what I did. it's still holding strong.
@bigj3086
8 ай бұрын
@@MotersickleBumI have a brand new AGM battery that my son broke the positive terminal off from. Been looking at any and all ways to repair it. This is the first one ive seen where they apply that much heat? Was wondering if it would blow up or not??
@MotersickleBum
8 ай бұрын
@@bigj3086 I just used a pvc mold over the old broken terminal but first drilled down into the broken terminal and then drove a sturdy screw into that hole. then i put my mold over the screw that was sticking up and poured the molten lead in. it's still holding strong. If I had it to do over, i'd use 1/2" copper tubing for my mold so that I could just leave it in place. scuff the inside of the copper tube so that the lead sticks to it. BE CAREFUL WHEN POURING THE MOLTEN LEAD. safety first.
@MotersickleBum
8 ай бұрын
@@bigj3086 make sure that you cover the neg terminal when working on the positive terminal. you don't want to short the battery while you're pouring the lead.
@mas2ery
Жыл бұрын
grey conduit! 👍
@wizdumb420
Жыл бұрын
What did you use for your mold?
@someguy9778
Жыл бұрын
pvc pipe
@ayitikonekte
4 ай бұрын
Plastic you mean ?
@KhushbooGupta-io3lj
11 ай бұрын
Bhai terminal toot gya hai to wah pe लोहे के नट को जोड़ के solding karke jod sakte hai
@GetRealBaby
Жыл бұрын
Why did you saw off what looks like a perfectly good battery post? Clean it up with a file and you're good to go, right?
@AhmadAbib
Жыл бұрын
Looks like the post worn out and got smaller, so the terminal clamp couldn't get a good bite...
@GetRealBaby
Жыл бұрын
@@AhmadAbib I would have cleaned up the post, wrapped it with galvanized plumber's tape and that should have provided the clamp with plenty of bite. This guy did it the hard way.
@Banditemcee123
4 күн бұрын
This guy did it the right way!@@GetRealBaby
@mauriciomacedojunior45
2 жыл бұрын
👏👏👏👏
@jerosilinjith9765
2 жыл бұрын
👍👍👍👌👌👌👌
@bernardgraf7187
Жыл бұрын
Best video 👍
@wendypilley1505
10 ай бұрын
Boiling hot water or even Coke would have cleaned away that acid in a jiffy and saved you doing this. I guess anything 4 a video right.
@FrankGrimes9
3 ай бұрын
You don't even understand what you saw. Amazing 🤩
@wendypilley1505
3 ай бұрын
@FrankGrimes9 Arhhhhh Grasshopper, you have so much to learn
@dannysmobiletuneup8317
2 жыл бұрын
What's in the pot?
@GetRealBaby
Жыл бұрын
I think he used lead but not clear where he got it. And was the soldering necessary at the start of the video?
Пікірлер: 33