Thank you! It worked like a charm. A little improvement I did was to drill through that little rubbery thing (2:50) and re-use it to hold new cable in place. No glue needed.
@techzact
3 жыл бұрын
You are welcome. Im glad it helped 🙂 Nice solution :)
@dicecard921
Жыл бұрын
What did you use to drill through the rubber?
@aarghhgraa
Жыл бұрын
@@dicecard921 I used the smallest drill bits I had at home. Just that and a lot of patience xD -- the rubber thingy stretches when drilled so the result diameter of hole is less than drill bit's diameter. For the life of me, I don't remember which drill bit was just right for the job.
@Emperorrobert
10 ай бұрын
@@dicecard921 Iron driller 2 mm - 3,5 mm at 0,5 mm stepp
@zahasanusi3823
3 жыл бұрын
Thank you!. U make me fix my Superlux Hd681 that have been broken almost 2 years. Easy to follow tutorials.
@durczyslaw1
Жыл бұрын
Thank you. That was very helpful. My Syperlux sounds properly again.
@Emperorrobert
10 ай бұрын
Thank You very much, I fixed my wife headphones today, by Your video. One thing: I used the original cable holder, drilled up to 3,5 mm.
@dowjones5981
2 жыл бұрын
I have the Superlux HD668B headphones and a reviewer from Amazon recommended to use heat shrink tubing on the 3.5mm plug. I did that on my headphones and its much more sturdy. I will still be careful with it. I guess some people are very rough with the headphones or accidentally yanking them. Try it. It doesn't cost much.
@kurdegg
3 жыл бұрын
Took them out of the box after 2 years of sitting broken and I find this video added two weeks ago. Really good one thanks!
@techzact
3 жыл бұрын
Hope it helps ;) thanks
@kurdegg
3 жыл бұрын
@@techzact It just did! Thank you very much :)
@techzact
3 жыл бұрын
You are welcome :) you made my day
@Towbee92
2 жыл бұрын
Thank you for the video. I managed to keep the plug, was tricky but works fine. Glued it into place with hot glue, now it comes out of the hole left from the cable but its rigid.
@Rehpotsirhc
Жыл бұрын
I can actually hear your voice perfectly fine even with a broken cable despite everything else sounding unrecognizable
@valerymoyseenko
2 жыл бұрын
Thanks a lot, it was really helpful for me. The same problem, I got stuck at the point of disassembly and did not dare to apply force. You took this risk for me and others. Unlike your case, I just made the cable with the jack near the headphones a little longer, now it resists bending better. The manufacturer must do this from the very beginning.
@yosto7522
2 жыл бұрын
Thanks it was very helpful. A suggestion, if theres enough room you can make a knot with the main cable right before you connect the red-white ones, that way not matter how much force you put on it, it wont be damaged and you dont need extra tools (hot glue).
@giano_olanzo3108
3 жыл бұрын
Finally a good video on how to fix them, appreciated 🙏
@techzact
3 жыл бұрын
Thank you! Hope it helps :)
@vulkaras7745
Жыл бұрын
Thank you very much, it helped me with my superlux hd668b.
@techzact
Жыл бұрын
I'm happy it helped :)
@pelaoconbeatle
2 жыл бұрын
muchas gracias amigo, no podía permitir que mi compadre muriera por el cablecito. Thank you! ❤
@miguelcerpasantana3953
2 жыл бұрын
Thank you very much, i fixed 2 superlux with this video,
@clinker123
3 жыл бұрын
Thank you. This was perfect. Other videos are not clear at all.
@techzact
3 жыл бұрын
Thank you! I tried to be simple and understandable :) Im happy it happened like that :)
@ericwright1488
2 жыл бұрын
hint: right after you buy them, put hot glue on the connector from the earphone (let it cool down and repeat, multiple layers 2 or 3 times), so it gets hard like a tank, if it does not move, it cant break. thats how i use mine since 5 years :)
@otactp3285
2 жыл бұрын
What if its already a bit chipped?
@ZWCaleb
2 жыл бұрын
@@otactp3285 will be fine as long is the wires arent damaged internally
@ares23dc
3 жыл бұрын
I love these headphones. I had 3 pairs breaking on me already. I keep buying them as I've tried more than 20 headphones under £100 and none of them match these.
@techzact
3 жыл бұрын
I’m also using them after repairing, however I could buy new ones but I dont need cause they are good enough :) thx for your comment! Have a nice day!
@frederickwood9116
2 жыл бұрын
Instead of replacing the full cable. Possibly install a 3.5mm jack or a socket. In this way the damage is reduced or even prevented. They will look a bit like the 681 EVO with the detachable cable.
@stefansegi2540
2 жыл бұрын
Saved me both money and time. Thank You very much!
@stefansegi2540
2 жыл бұрын
But fuck the deliberately flawed design of the cable. Whoever done it should be kicked in the arse.
@gamma921
3 жыл бұрын
Köszi ezt a videót is! :) Rendes tőled, hogy a hibát is benne hagytad, hogy más már ne fusson aknára. Csak így tovább!
@techzact
3 жыл бұрын
Nincs mit :) koszi szepen, orulok, h segitettem :)
@piermariamontalto6563
10 ай бұрын
You saved me, thanks a lot
@EfeBurakOfficial
Жыл бұрын
gosh yes, Im having exactly the same problem. thank you soooo soo much 👍👍🙌🙌👌👌
@brandongcassels9009
2 жыл бұрын
Thank you so much, just saved me R600, thats about $38 in your currency. Much appreciated
@techzact
2 жыл бұрын
You are welcome :)
@stealthghost3000
3 жыл бұрын
Thank you! I finally fixed mine
@techzact
3 жыл бұрын
I'm happy, you are welcome :)
@faizfrez2729
2 жыл бұрын
Hello, i tried following as closely as in the video, and managed to get this piece of junk i found that doesn't make sound at all, to make sounds on both sides! However i noticed when i tried testing the sound, it seems that the sound is flipped between left & right. And also one side doesn't produce any bass. Is that possible because of bad connection from the solder? Or the driver just aren't good anymore?
@grazz_er
2 жыл бұрын
Thats a great pair of headphones! I am using it for 3+ years already and they have been repaired 5+ times :) BUT, the last time I tried to fix them again, but it didn't work. I bought a new 3.5 plug and soldered it. Still, my right speaker does not work. Under plastmass near right speaker everything seems ok. So, i think it is broken somewhere inside (under right speaker or inside of metall headband). Can you give me a hint what can be a problem? I did not drop them, so right louder should be ok. Thx.
@grazz_er
2 жыл бұрын
I have changed the plug again and it actually started to work! That's amazing headphones, haha. I think they never die if you repair them everytime :)
@adamhnat5123
3 жыл бұрын
Maan thank you :) Great tutorial, works like a charm
@techzact
3 жыл бұрын
Cool 😊 you are welcome ;)
@cengizkenet
3 жыл бұрын
Thank you, Man 😀😀 sound is back😄👍
@techzact
3 жыл бұрын
Super cool! You are welcome :) I thought for your profile picture that there’s a hair on my screen 😃
@cengizkenet
3 жыл бұрын
@@techzact 😂😂😂 nice so it worked with the hair
@techzact
3 жыл бұрын
@@cengizkenet so that was the intent :DD
@VitaFireLL
3 жыл бұрын
How can i find out which wire i should connect to left/right/ground? I wanted to solder a 3,5mm jack in. but i am not sure which is left and which right.
@techzact
3 жыл бұрын
In most cases red is right and white is left but you should google it 🤷♂️
@GULIwer1980
2 жыл бұрын
From another video Headphone red->Cord red (right) Headphone blue->Cord White (left) Headphone copper/yellow->Cord black (ground)
@giovannigola2359
3 жыл бұрын
Good job
@techzact
3 жыл бұрын
Thanks a lot :)
@streetlegal008
Жыл бұрын
This is a design problem with the Superlux - but it should be possible to replace the input socket with a better quality metal socket - very cheap components - and wired as original. That way you can make use of different cables as intended. It makes sense to me to have the socket on a small length of wire so that it is say 50cm away from the headphones. Also when soldering small wires like this it is best to reinforce the joint with a small length of heat-shrink tubing.
@agustingribaudo5162
3 жыл бұрын
do you know how to protect the cable to prevent this?, thnxs
@techzact
3 жыл бұрын
The quality of that cable is not so good, that's why it's getting broke for a lot of people. Maybe you can put some tape around that part and be gentle with it when you use the headphones, but other than that I think there's no way to prevent it.
@agustingribaudo5162
3 жыл бұрын
@@techzact its good idea, Im going to try whit tape. Thank you, nice and usefull chanel. good luck!
@techzact
3 жыл бұрын
@@agustingribaudo5162 hope it helps :) You are welcome and thank you very much :)
@yukkimura
3 жыл бұрын
I recommend buying a solid braided cable and then soldering it like this, even the amazon basics braided cable will last an insane amount of time.
@techzact
3 жыл бұрын
@@yukkimura thanks for the advice :)
@solidus3659
3 жыл бұрын
Can i use female part of extension cable instead? So I can have a detachable cable
@techzact
3 жыл бұрын
Could you describe this more accurately please?
@solidus3659
3 жыл бұрын
@@techzact Hi! I’ve already replaced it^^ thanks to the video it all went smoothly, it was my first time soldering and your tutorial was perfect for me! Thanks a lot, you earned yourself a subscriber :D imgur.com/gallery/oR0VTEy
@techzact
3 жыл бұрын
@@solidus3659 WOW, Cool. I'm glad to hear that. You're welcome. Thx for the sub and have a nice day! :)
@solidus3659
3 жыл бұрын
@@techzact you too! :)
@techzact
3 жыл бұрын
@@solidus3659 thank you :)
@andreasankara
Жыл бұрын
Grazie mille, un saluto dall'Italia!!
@william1482
3 жыл бұрын
You are a lifesaver!!!!
@techzact
3 жыл бұрын
Thank you! I'm glad it helped :)
@niltonjr7213
3 жыл бұрын
my solder don't fix in the cable.. Do u use paste?
@techzact
3 жыл бұрын
No, because tje solder which I used has flux inside.
@ulle500
2 жыл бұрын
2:25 OH it just slides off. The rubber band on mine broke just few days after use (I guess my head is too big) so I replaced it with a normal rubberband.
@drakon_ex
4 ай бұрын
Why they keep building them with that jack plug, it is really bad and always breaks.
@vadimuha
5 ай бұрын
Your connection is weak and will brake soon. You need to twist wires together first to making a light mechanical connection, then apply solder
@marcostobiasmora3099
Жыл бұрын
tuve un proble que solo se me escucha del lado derecho y segui los pasos como lo indica el video
@techzact
Жыл бұрын
Sorry but I don't know what could be the problem. :(
@TheGalacticIndian
6 ай бұрын
They should sell all Superlux headphones as DIY kits - quality is a lottery, and you still need to get it right sooner rather than later. So it's better to solder the thing yourself!😠
Пікірлер: 80