Take the wheel out, take the clip off the wheel, remove the outer rubber strip, flip it inside out, [important]>>bend it all the way around with the used side folding inward, if you dont, the fresh side will bow in a concave fashion all around...so you want to eliminate that bend and make the surface even all across... Then refit the clip, and stick it back in the printer. BONUS TIP: The inner surface is quite 'grippy'. Scuff it up with some 800/1200 grit sandpaper, or rub it a bunch on the pair of denim jeans you're hopefully wearing. If you can successfully print out around 5 test pages in succession, you have just saved yourself 15 bucks.
@torquaster
Жыл бұрын
Thank you, that worked great for me on 3 HP CP 1525n printers and saved me quite a lot of money.
@ECHOBELLATOR
Жыл бұрын
YES!!!! This is what I did. The other side of the rubber belt is pristine. You should get the same number of years out of the other side as you did the origional side.
@RanjitSingh-fu2nn
Жыл бұрын
🥳🥳🥳🥳🥳worked thanks
@thejayhab
Күн бұрын
Thanks very much, just done this on a printer that was given to me and it's fixed the jam in tray 2 problem! ❤❤
@realvi
2 күн бұрын
thank you! We all love you
@louisverhagen
Жыл бұрын
Great Video, explains everything. Like Alixe I also changed the rubber on the roller, but I routed it by 180 degrees. That way you will be able to use a roller rubber 4 times :-) :-) But for the costs of a roller I would suggest getting a replacement ;-) As it was a holiday I had no choose and to service it with Alixe suggestion.
@ricolebreton583
2 жыл бұрын
Great! Works again and I saved a lot of money, was about to buy a new printer!
@ea4gkq-angel764
2 жыл бұрын
Great.!! My printer is working perfect again. thanks!
@RanjitSingh-fu2nn
Жыл бұрын
Thanks dude worked perfectly fine
@sleeplessbeauty5602
2 жыл бұрын
Oh how I needed this.
@microsoftsarker
7 ай бұрын
Thank bro..
@Okipentv
7 ай бұрын
Welcome
@sufyanrajput9264
3 жыл бұрын
Thank bro.. problem solved. 😍
@Okipentv
3 жыл бұрын
Great 👍
@jiajialim3006
2 жыл бұрын
how to solve the printer cannot print multi page. It always show jam in tray 2 when it start print page 2, when I pull out the tray, is more like the paper cannot roll up. It didn't jam. If I print one page each time then no issue. I replace a set of pick up roller, the problem remain. Thanks
@navneetvaghela9265
3 жыл бұрын
I will try this tomorrow in office and will let u know !!!!!!!!!!!!!
@jonygudel8419
3 ай бұрын
thanks
@sebastienturmel6211
8 ай бұрын
Bonjour, j'ai une question j'ai remplacer le pick roller et le petit mais ça ne veut toujours pas prendre les feuilles ou très rarement Pouvez-vous m'aider svp 😢
@jor3725
2 жыл бұрын
Me pasaba lo mismo en una HP CP1525MW, le cambie tanto el pickup como el separation pad pero me sigue dando atasco.... a que se debera?
@user-ie7ow4eh1v
3 жыл бұрын
V Good👍👍👍👍
@Deadpool-ODST
2 жыл бұрын
Mine is less than a year old and started jamming on every print. It use to at least print one page but now it won't print at all and says there is a jam even though there is nothing there.
@ahizechris7771
3 жыл бұрын
Thanks, nice tip. Do you have solution for shadow printing of this printer?
@jauneetbrun
Жыл бұрын
I had a shadow printing problem when I bought cheap ink cartridges. The problem went away when I bought official HP printer ink cartridges (which are really expensive).
@norazmandaud2189
3 жыл бұрын
i already try this but my pickup roller cannot rotate. how?
@ahizechris7771
3 жыл бұрын
I had the same issue when I first watched the video and tried it out. I just tried it and it worked perfectly. Watch the video again
Пікірлер: 28