LOVE this video. I have searched in vain for some adjustment and found none. Never figured it could be this simple!
@diymacgyverguy8054
2 жыл бұрын
Awesome
@paulpalmer7353
2 жыл бұрын
Been struggling with tracking out for ages, scuffing the tyres and the lawn. Thanks to your video, all fixed and no cost ! Thanks from Ireland.
@diymacgyverguy8054
2 жыл бұрын
Awesome!
@feduncan
Жыл бұрын
Thank You! My wife drove my lawnmower one time, and when she got through with it, one tire was pointing east and the other west! 😎
@diymacgyverguy8054
Жыл бұрын
Haha, it happens!
@donaldshimkus539
Ай бұрын
😂
@steveleggett344
2 жыл бұрын
This is the easiest and most cost effective repair I have seen for tire alignment. I was heating and bending the steering rods with a BIG hammer. (after flipping the mower on its seat with the front end in the air) I will do this from now on. THANKS for the tip!!!! My back also thanks you!!
@diymacgyverguy8054
2 жыл бұрын
Sounds like how I change the blades
@paulleblanc4653
2 жыл бұрын
The front mower support rod is also bending axle back, drilling a new hole in flat plate on steering knuckle and moving linkage also works well. The newer models have adjustment on both rods. Never seen your method, genius.
@danogilbert1775
2 жыл бұрын
What makes the front tire turn out when you put it in reverse
@jake2102
Жыл бұрын
@@danogilbert1775check the bushings in the rims. Lose fit will for sure cause issues in reverse. You can buy replacement bearings for the wheels to replace bushings
@therising1
Жыл бұрын
@@danogilbert1775the spindle "bearings" are worn. Watch the front end when you do it and you'll see where it's moving.
@tomtomkapow
Жыл бұрын
Dude. This video needs more exposure. Everybody else is like "Here's a quick simple fix, all you need is a Mig welder, some angle iron, these new ball joint parts, an old priest, three helpers, congressional approval, and this specialty tool I won't name or tell you where to buy."
@diymacgyverguy8054
Жыл бұрын
Haha thanks!
@gnarkilleptic4871
6 ай бұрын
Seriously. Other videos have me ready to buy a whole new assembly
@blingblingg31
5 ай бұрын
@@gnarkilleptic4871 same
@Bailey-y9b
5 ай бұрын
LOL Tom
@user-dz7te7jd1s
5 ай бұрын
So true!
@judyjohnson630
2 ай бұрын
I finally realized why certain parts of my lawn have been having less and less grass each year for the past couple of years. It's where I turn at the end of a strip of mowing, amd my wheels are toed-out, so the tires have been ripping the grass up! Every single time I turn, one wheel is being forced the drag along the grass!
@glennyj65
Жыл бұрын
I can't believe I'm just now seeing this after YEARS or tearing it down and using the vice! Tried it a few minutes ago and wow! Big time saver! Thank you!
@Skipfamous
2 жыл бұрын
Brilliant. Concise and helpful how-to. Solved my problem without having to thumb through too long of a video and listen to too much chit chat. Thanks man!
@diymacgyverguy8054
2 жыл бұрын
Everyone aims for at least 10 minutes because you get an extra Advertisement lol. So even simple stuff gets stretched
@arthurrodriguez795
Ай бұрын
Freakin Awesome!! Appreciate you man. Saving money for people all across the Country.
@chrisb.1301
6 ай бұрын
Damn, glad I found this video!!! Soooooo much simpler than most other videos I’ve watched. This is definitely an easy way to fix my issue with toe out
@mountainplumbing
2 жыл бұрын
Fixing my Girlfriends very old Mower with this problem this weekend. Was going to cut the linkage and put a shaft coupling on it. So thankful I found your better and easier fix. All hearo's do not wear a cape. Thank You Sir!!!!
@diymacgyverguy8054
2 жыл бұрын
LOL it is super easy
@davidhollingsworth950
2 жыл бұрын
Thanks! Exactly what I need to do on my old Husqvarna. Great video.
@spontaneouswill007
Жыл бұрын
Thanks for the video, straight to the point no blah blah blah…. Excellent 👏!
@diymacgyverguy8054
Жыл бұрын
Haha, If it bends again watch the permanent fix video too
@DougHolcomb-yi7vj
3 ай бұрын
Would love to see the "full" version. Thanks!
@richardtriplett2592
7 ай бұрын
Thanks for the tip on bringing in the wheels straight. It worked perfectly!
@diymacgyverguy8054
7 ай бұрын
Awesome! If they bend again over time check out my permanent fix video
@onebladeprop
Жыл бұрын
I was about to order a new set of spindles but I'm glad I found this first.
@diymacgyverguy8054
Жыл бұрын
Awesome, check out the permanent fix video too for reinforcing kzitem.info/news/bejne/uY1jro2mgGV4ZZwsi=rsLl3BSMmsT624YJ
@pgchustla
2 жыл бұрын
Man, great idea! Been dealing with a bow legged tractor for years
@samscott54
2 жыл бұрын
the best turoial Ive seen... clear and accurate - nice job
@pmaint1
2 ай бұрын
Thanks for the video. My wheels were toed in which made it almost impossible to bend them out. These front ends are pretty much garbage.
@703am
2 жыл бұрын
wow, been dealing with this same problem for years now , i just put up with it , thanks to you i now know what to do..
@diymacgyverguy8054
2 жыл бұрын
Awesome!
@davemullner7170
Жыл бұрын
Thanks man! That's a lot easier than pulling both spindles off!
@diymacgyverguy8054
Жыл бұрын
A lot quicker!
@jerryh5271
Жыл бұрын
Great video--good to find a good ole boy that has his stuff together !
@JohnSmith-mv6bw
11 ай бұрын
Bro!!!! THANK YOU!!!! been fighting with this for years with a POS Ariens I have.
@00Widget
2 ай бұрын
That was brilliant.. saved me a headache . Good work on the video btw
@diymacgyverguy8054
2 ай бұрын
@@00Widget thanks!
@Jorgedelprete
10 ай бұрын
Muchas gracias señor, saludos desde San Esteban Córdoba Argentina
@frisk151
Жыл бұрын
My time saving HERO!! Thanks Brother!!!
@StarKnight619
4 ай бұрын
holy shit........I have a craftsman that we got a few days ago with this EXACT steering setup and problem. I have the pipe just not the pipewrench...................picking one up tomorrow
@richienichols7958
Жыл бұрын
Good practical video. I had this problem that I thought was caused by bent axles. On closer inspection the chassis was buckled causing the steering tie rods to "lengthen" . The solution was to lift the mower with a front end loader and using sledge hammers take the buckle out of the chassis on both sides. A stiffening plate 50mm EA was used with several bolts to provide a permanent solution. QED
@gggrace2384
Жыл бұрын
I'm now wondering if my G5600 has a chassis problem; I've replaced all the front linkage and one of the wheels is still toed out too much. I'm going to look for this.
@diymacgyverguy8054
Жыл бұрын
Wow! So your friend was actually bent? I haven't seen that yet what did you hit?
@diymacgyverguy8054
Жыл бұрын
You replaced the spindles? Cause that's the part that bent in my video?
@jimdavison4077
Жыл бұрын
Well it's a temp fix but one that will serve many so thankyou for that. I think I will use it but then weld some form of strengthening in the under side after so that they can't bend again. I cut about 4 acres sometimes twice a week. Machin had about 900 hours on it and I have a Craftsman Pro that is the mate to it. 26hh54 in cut. Should work on both. Also they have bearings available on line to replace the front bushings which wear out. They roll easier and this is the second year and no problems with them. I had to replace the bushings and didn't get a year out of the replacement ones, softer material. Another thing I noticed was the bracket you used to jack up with bends over time, mine had to be bent back about 3/4 of an inch so that was affecting deck height and stopped it from lifting to full height. This with a 54 inch deck over rough ground made the machine get stuck several times and they are not light like smaller machines. There is also a shim on the pivot point on the cast front axel that wears along with the plate that bolts it on. I had to put spacers to stop the entire axel from tipping which caused the toe out you were fixing as well. As the axel tips forward it pushed back on the tie rod ends and tips the tires apart. The sad truth these machines are not made for years of use like older machines out there and the newer ones are even worse. Again thanks for sharing tips and ideas, they do help a lot of people. Have a good week, cheers from Canada.
@diymacgyverguy8054
Жыл бұрын
Thanks for the comment, Please check out my "Permanent Fix" video for these spindles. kzitem.info/news/bejne/uY1jro2mgGV4ZZwsi=rsLl3BSMmsT624YJ
@jathgillam9175
7 ай бұрын
Lifesaver! Love your work, cheers.
@olyokie
7 ай бұрын
Cool dude am going to try this today on my old JD……
@diymacgyverguy8054
7 ай бұрын
If i get time this year im going to make reinforced front axles and offer them for sale... see my other videos on permanent reinforcement
@Bens-service-and-repair-garage
10 ай бұрын
Thank you so much for your help and time.
@markho170
2 жыл бұрын
Awesome fix. Thanks for sharing!
@warrenvalentino5763
2 жыл бұрын
Thank You So Very Much for this video. it Realy helped me fix my ride on mower. :)
@diymacgyverguy8054
2 жыл бұрын
Glad it helped!
@boomerau
Жыл бұрын
there are a couple of nuts that you can undo and adjust it without taking wheels off. the bushes will also go in the wheel which is a whole separate problem
@donaldshimkus539
Ай бұрын
I have an 18 yr old Cub Cadet 25 HP. It has had steering problems almost from day one. The last year I used it the wheels were all over the place. I have installed all new parts to no avail. Finally got it adjusted to where the front wheels are straight going forward, but in reverse the wheels splay out badly in the back. Mower sways side to side in reverse. Damn MTD crap.
@bigbagboy8992
2 жыл бұрын
No some shit don’t it lol smart man!! You gained a new follower
@marksmith2884
Жыл бұрын
Thank you for this. Simple and works.
@diymacgyverguy8054
Жыл бұрын
Glad it helped
@ken3700
2 жыл бұрын
Thank you buddy your a genius !!!!!!
@derricksauls2008
Жыл бұрын
Thanks buddy. This is exactly what I was looking for but I'm not eating you lol
@diymacgyverguy8054
Жыл бұрын
Haha. I left that in there on purpose I thought it was funny
@gordieman
2 жыл бұрын
Ahhhhhhhhhhh!!! That's it maaaan!!! Thanks!!
@redjones5836
2 жыл бұрын
Thank you Dude!!" A sensible no nonsense Fix!! my old mower had Adjustable linkage. makes me sound like my parents " They don't make shit like they use to" now its just Shit ! Thanx Again for good no Bull Video.
@diymacgyverguy8054
2 жыл бұрын
Lol glad it helped! Sadly whether you replace it or bend it back, it is a weak part and might reoccur. Check out the video I just posted now on how to permanently reinforce it (you will need to weld tho)
@mblack360
Жыл бұрын
Very helpful, thanks!!!!
@motoman5023
2 жыл бұрын
That is a awesome trick thanks
@jason22landry
Жыл бұрын
You Da man!!!! 🙏🏾
@diymacgyverguy8054
Жыл бұрын
Thanks for the feedback
@nelsonthekkath4830
2 жыл бұрын
I don't need in here! Before happening this, my customers break the engine apart 😁😁😁
@gerardi2000
2 жыл бұрын
Bruh! that was awesome! Thank you!
@Chinstrap-99
2 жыл бұрын
Thank you so much!!
@bkrman1990
2 жыл бұрын
I was watching other videos and actually thought to myself why not just bend it back in place? My issue is camber I'm thinking I can do the same and just bend up or down to adjust the camber
@diymacgyverguy8054
2 жыл бұрын
You can but it's a lot harder because you have to bend that thick spindle. I bet you can tho. Side note if you want to replace the spindle they are only $15 on amazon.
@bkrman1990
2 жыл бұрын
@@diymacgyverguy8054 thanks! I saw some of the comments on amazon people were saying the steel isn't as good and they bend easily.. I'll try bending first, with a big enough hammer it shouldn't be too hard 😂
@diymacgyverguy8054
2 жыл бұрын
Next week I'll be uploading a forever fix to the toe in but you'll need a welder.
@diymacgyverguy8054
2 жыл бұрын
@@bkrman1990 new video dropped today for the permanent weld fix
@riverrated619
Жыл бұрын
When I bought my used mower it was toed out pretty bad. I replaced both wheel spindles and nothing changed. Would this still work on spindles that have no damage?
@diymacgyverguy8054
Жыл бұрын
Sounds like something else is wrong. I'd check the front axle that the spindles are attached to. Some have a pivot point in the middle and the bushing goes bad and allows it to lean
@TadashiYasahiro
2 жыл бұрын
💀💀 bruh!! You ever seen something done so simply it made you feel completely stupid! Thanks bro! Will fix mine tomorrow!
@diymacgyverguy8054
2 жыл бұрын
LOL no problem good luck
@TadashiYasahiro
2 жыл бұрын
@@diymacgyverguy8054 tried it, fixed it and it turned out great! thanks again!
@Freedom_Rider915
3 ай бұрын
Don’t do this to your mower unless you have a welder! The little weld that is on the steering will break off! I tried it and it’s the first thing that happened. It took me hours to get the alignment done. This guy doesn’t mention anything about it but don’t take my word for it.
@nathanaldrich4633
3 ай бұрын
You must have have very bent spindles or something because I’ve been riding mine out for almost 2 years from this video I just came back to it to help a buddy lol but yeah must have had some super bent ones to break the welds honestly unless you just had bad luck with bad welded spindles but who knows some things don’t always work for others ya know sadly to day
@colt5189
Жыл бұрын
Do you remember what internal ID of that pipe you used? As I'd have to order one. Thanks.
@diymacgyverguy8054
Жыл бұрын
It was a standard large floor jack handle.
@MrJHart
2 жыл бұрын
So I did this to my Husqvarna TS 248 TD and it initially worked, but now my right wheel turns independently. It seems that the spindle shaft is broken. How are you able to bend the spindle shaft without breaking it?
@diymacgyverguy8054
2 жыл бұрын
The steering arm attachment tabs on the spindle bend pretty easy. If your spindle is broken you definitely need a new one. I have another video of a welding reinforcement if you have a welder or have a friend with a welder. Just need a tiny piece of scrap angle
@alantherealestateguy6833
Жыл бұрын
Good video!!!!!!!!!!!!
@diymacgyverguy8054
Жыл бұрын
Thanks!
@dennismorris9763
2 жыл бұрын
thank u thank u thank U
@diymacgyverguy8054
2 жыл бұрын
This is definitely the easy way, I have another video that includes welding that reinforces it so it will never bend again.
@michaelhayes413
Жыл бұрын
I’m 6’2” and 225 pounds and damned if I could bend that arm
@diymacgyverguy8054
Жыл бұрын
Lol I'm 180 but with the strength of Thor. Not the God tho.. just the bodybuilder
@colt5189
Жыл бұрын
Is the part that gets bent the part that the wheel goes on? I'd have to look up prices on what those two parts cost in comparison to having to buy a metal pipe. Also, can you recommend places online that sell Husqvarna parts that are legit? As I went to buy parts and checked out several online dealers, to then search the company to find they have one star reviews and apparently those places never respond to phone calls or email. Need to buy a new wire harness and a bunch of miscellaneous parts. Thanks.
@diymacgyverguy8054
Жыл бұрын
I use e replacement parts or parts tree. The part that actually bends is the tab where the linkage connects
@colt5189
Жыл бұрын
@@diymacgyverguy8054 Thanks, have you had any issues ordering from those places? I have a bunch of parts I'm going to need to order. I've already gotten half off of eBay. But some I need aren't there.
@diymacgyverguy8054
Жыл бұрын
@Colt those places have really good diagrams. So once I figure out the part number I need, I usually search the part number on Amazon and order from there. The less places with my card number the better.
@colt5189
Жыл бұрын
@@diymacgyverguy8054 I ended up ordering a couple of parts off of Amazon. It was direct from the seller, and they didn't charge shipping for some reason. The rest I've ordered off of eBay and actually got pretty good dealers on brand new items. I've got to repaint the orange frame part that is under the battery as there's a large section where the paint has come off. I plan on getting Eastwoods 2K Duraspray orange paint to repaint it. As it should hold up better than regular 1k, and I should be able to get away with just that one paint.
@carlthornton3076
2 жыл бұрын
Very Good!... #36 🐄🦉🏴☠✝{5-2-2022}
@daleyhanson5889
11 күн бұрын
But all I have is noodle arms,, not the pythons I used to have,,,😅
@bigsonslawncare
2 жыл бұрын
👏🏽💯💪🏽
@DiscipleoftheDumbOx
Жыл бұрын
Sadly, I tried this without success. This requires upper body strength I do not possess.
@diymacgyverguy8054
Жыл бұрын
You can do it! Archimedes said "Give me a place to stand, a lever long enough and a fulcrum. and I can move the Earth"
@JamesDubois-ss4fc
Жыл бұрын
Sorry I call bullshit tried that on one there is no way to bend it like you showed doesn't work
@baldeagle242
2 жыл бұрын
Simple fix for a common problem! Supper strong cast iron front cross beam and cheap stamped metal linckage! You also have your 10th sub. I'll be watching for sure. 🦅🦅🦅
@diymacgyverguy8054
2 жыл бұрын
Hey I've seen a couple of your videos! I just went to your channel and looks like you had a few videos hit big and went 1k sub 12k really fast! Awesome man!
@baldeagle242
2 жыл бұрын
@@diymacgyverguy8054 Yes, I started getting serious in early 2021 and have had a little run of luck over the past year. I have fun with it and really enjoy sharing and meeting other like minded people more than anything. From what I’ve watched on you’re channel you’re about where I was at the start of 2021. Keep at it and it will take off for you as well. 😁👍
@freddiewright8270
Жыл бұрын
Thanks. Great video
@diymacgyverguy8054
Жыл бұрын
Glad you liked it!
@karenbearden6198
3 ай бұрын
Thanks so much!!
@ohmythatsweird
3 ай бұрын
I've been fighting my steering wheel for over two years now. THANK YOU. The other videos just show you how to replace the spindle.
@diymacgyverguy8054
2 ай бұрын
@@ohmythatsweird it’s a very common issue the spindles are weak from the factory
@scottsouder7544
2 жыл бұрын
Fabulous! I was all set to drill a questionable hole like the other videos suggested but came back in the house for some last minute fine tuning on instructions and just for the heck of it, clicked on one last video, yours. Thank you SIR! Much easier, much faster and much smarter. You earned a sub. Now let's go out and see how she drives.
@diymacgyverguy8054
2 жыл бұрын
Awesome! Sadly its a weak part and it will bend over time regardless of replacing it or making an adjustable tierod... I made a second video showing a permanent welding reinforcement. A couple people have suggested I make them and sell the reinforced part.
@Scott.Farkus
2 жыл бұрын
Finally someone figured out what was causing that. 😃 Thank You.
@diymacgyverguy8054
2 жыл бұрын
And just so you know if you decide want to replace it just search husqvarna front mower spindle and they are about $15. However the new one will bend just as easy lol
@Scott.Farkus
2 жыл бұрын
@@diymacgyverguy8054 I noticed it's not that hard to bend. I'm thinking about hooking up my mig welder and reinforcing them somehow.
@diymacgyverguy8054
2 жыл бұрын
I'm actually going to upload a video for a permanent fix next week. I'm pretty sure I can just weld a little piece of flat metal between the steering stop and the tie rod attachment point and then it'll never bend again. I'll call that video "the permanant fix"
@hester781
2 жыл бұрын
Awesome job buddy, in the past I’ve bent those tabs downward slightly towards the front but I like your idea better!
@rayvojtash2344
Жыл бұрын
By far the best and easiest way to fix the steering on these lawn tractors. Thank you.
@diymacgyverguy8054
Жыл бұрын
Thanks!
@Loris8768
Жыл бұрын
No es la solución, hay desgaste, lo más malo que tienen todos los cortacésped son el tren delantero..
@BarnyardEngineering
2 жыл бұрын
Well hell that's a lot easier than what I was trying to do! I was trying to put more bend in the tie rod itself which involves removing the tie rod, but you can't get to the back end of the tie rod.
@diymacgyverguy8054
2 жыл бұрын
That's what I was thinking at first too! Then I was like... wait why don't I just bend the tab back? Sadly it's a weakly designed part. I have another video showing me welding a reinforcement onto the tab so it never bends again
@CheekyMonkey1776
2 жыл бұрын
Quick and easy. Thanks!
@Tone-hb2sm
5 ай бұрын
Thanks I’m having that issue just ordered all new parts you are a life saver!
@diymacgyverguy8054
5 ай бұрын
Glad it helped
@discokillers8674
Жыл бұрын
Amen!!!! Thanks for the info. I searched everywhere and heard all sorts of expensive solutions. Gotta live KZitem. Thanks for the tutorial!👍
@diymacgyverguy8054
Жыл бұрын
This is definitely the easiest way
@johnsradios484
Жыл бұрын
Thanks for the video
@therising1
Жыл бұрын
Ain't no way I'm bending the spindle on my Craftsman Gt5000. I was so hoping this wod work but I think this tractor has heavier duty knuckles. The tab on mine looks to be 1/4in steel or maybe 3/16. Great video nonetheless!
@Bailey-y9b
5 ай бұрын
You MacGyver guy have saved me a bunch of money time and aggravation to fix something this simple that others have not even thought about.Thank you very much for the super easy fix. I will be tuned in for future videos on maintaining this lawn equipment.
@diymacgyverguy8054
5 ай бұрын
Glad it helped!
@RidingHumboldtCounty
2 ай бұрын
I’m having the same problem. Are we bending the bracket or the spindle that holds the wheel?
@no_handle_required
2 жыл бұрын
what a crap design. Good tips. Use jacks so we don't have to see a mower attack.
@diymacgyverguy8054
2 жыл бұрын
Definitely a terrible design, probably an extra $1 of metal could be very strong. They probably like it that way though because they have been making that style spindle forever and it probably leads a lot of people to purchase a new one
@ozgeek81
7 ай бұрын
Thank you so much for the tips. My mower is out of alignment! I'll try those tips.
@JohnTiberiusD
2 жыл бұрын
Brilliant, Saved me a fortune, its so hard to get parts in Ireland and shipping from US is so expensive. Thanks for the Video, massive help
@diymacgyverguy8054
2 жыл бұрын
Glad it helped
@retiredhappy466
2 жыл бұрын
I've already fixed two tractors with new linkage for a cost of approx $100 each. But, I really like your solution.
@diymacgyverguy8054
2 жыл бұрын
Yeah this is way easier
@stevestott4291
4 ай бұрын
This is exactly what I needed to know. Exactly. Thank you.
@diymacgyverguy8054
4 ай бұрын
Haha awesome
@TomJones-no9bd
5 ай бұрын
Thank you! I fixed the toe out on the husky yesterday after seeing your video... super easy ...took me about 20 min. I appreciate the simple but effective fix...no welding or cutting just a little leverage. I used a little longer breaker bar on the plumbers wrench and the wheel hub and was super simple.
@larencegagland506
2 жыл бұрын
👍👍
@theagent530
5 ай бұрын
I have been seeking this fix for years.. I appreciate your every man ingenuity! Thanks for taking the time to show us how it’s done!
@GTObearclaw1
2 жыл бұрын
I’m subscribed now Iv been fixing mowers for years. So simple it’s stupid. I wish I’d thought of it. I got one to try this on tomorrow. I usually just swap the steering knuckles but I have a yard full of parts mowers to grab parts off of. Some of these I have found to have broken welds and that’s why they were bent. I guess they took a hard hit and broke rather than bent. So it can happen but your fix probobly will solve a lot of folks issues and that’s what it’s about, helping each other. So in those cases where the welds broke I clamp in vice and straighten best I can and weld. In one of my videos I bent a Deere body up to replace a tank and some KZitemrs pooped there pants over the Vidio. Sometimes folks don’t understand these things are cheep and just need some Tuff love once in a while. I love bending stuff so I can’t wait to get out side in the morning and twist some metal.
@diymacgyverguy8054
2 жыл бұрын
Haha that's the spirit. I also made a welding reinforcement video too for reinforcing it once you bend it back straight. Little piece of angle does wonders
@countryboy39051
2 жыл бұрын
Thanks so much for this! I have a horrible toe-out problem with my Deere and every video involved welding, which I can't do, this was much simpler!
@diymacgyverguy8054
2 жыл бұрын
Glad it helped, I made a video of both types of fix for people who didnt want to weld.
@jimdavison4077
Жыл бұрын
The only downside is ever time metal is stretched or bent it weakens it so straightening them is the second time to bend then and they are now weaker than the original time. Maybe get them straightened as shown in the video then pull the spindles and take them out to get reinforced? Solve the problem forever and not just a temp fix? Just make sure to brace the side away from the tie rod end which goes over the spindle bracket. Someone must have a welder close by? A bit of scrap steel and bobs your uncle.
@markclark8367
Жыл бұрын
I appreciate this video.
@diymacgyverguy8054
Жыл бұрын
Thanks!
@gerardog15
Жыл бұрын
It work. I was about to buy stering bars. And saw yor video. And wooala it works. Thank you man...
@diymacgyverguy8054
Жыл бұрын
Awesome! If it bends again check out the forever fix kzitem.info/news/bejne/uY1jro2mgGV4ZZwsi=4lrvor6HVogVB0-K
@blingblingg31
5 ай бұрын
Great video ... straight to the point... well illustrated.
@diymacgyverguy8054
5 ай бұрын
Thanks!
@Don-ul6rx
4 ай бұрын
Called my Husqvarna stealership and he said it would be $450 minimum! Where do I send the beer!
@mr.hoonigan4313
Ай бұрын
You weaken that every time you bend it back. Eventually it will snap on ya.
@jeffreyconrad8861
6 ай бұрын
Perfect! Simple, easy, to the point. Thanks.
@mikespain8655
Жыл бұрын
Thanks for this video. Simple and straight forward.
@snooter28
11 ай бұрын
I was about to buy all new spindles but yeah, threw the bar on there with a crescent wrench (not as nice as a pipe wrench) and then its WAY better.
@marchansen3629
4 ай бұрын
Dude you made it stupid simple. I was going to buy a bunch of stuff I did not need.
@diymacgyverguy8054
4 ай бұрын
Glad it helped
@marchansen3629
4 ай бұрын
@@diymacgyverguy8054 I did the process this afternoon and it was a snap. Thank you again. I now have front alinement on my mower.
Пікірлер: 289