I have thus problem, and now thanks to your video, I will check the power continuity today. I will message back to let you know how I go! Thankyou again for providing another path to troubleshoot.
@ARTaudio440
7 ай бұрын
Hi, you're welcome and thank you too for watching! ☺️
@frayedsanity
7 ай бұрын
@@ARTaudio440So I tried your checks, and I had continuity at the two small chips "U15" and "U16", and also had continuity when earthing the screw and checking "L35" and "L39" but that "L58" filter had no power going through it from either side, and the red LEDs on the switches no longer light up either. I installed a new screen because I thought that was the issue, but it hasn't helped anything...If anything I've made it worse 😒
@ARTaudio440
7 ай бұрын
@frayedsanity Hi, thanks for sharing your diagnosis, I can see that you have a missing volts on L58. Please check the reference volts as follows. L58 +9 volts Dc L35 -15 volts Dc L59 +15 volts Dc
@ARTaudio440
7 ай бұрын
@@frayedsanityPlease watch the full video carefully again and you can see it about the L58 which has a loose connection. Or check this 4:00
@frayedsanity
6 ай бұрын
@@ARTaudio440Where are the L35 and L59 locations?
@glxmusicstudioperdagangan
Жыл бұрын
Yes my friend thx alot It's work for me, resoldering The result : Lcd works, sounds works Thanks a loooottt 👍👍👍👍
@ARTaudio440
Жыл бұрын
Hi, you're welcome and thank you for watching 🙏
@billyghostal
7 ай бұрын
also, if it has a usb port, plug into a computer and run Line 6 Monkey on it, update the firmware and that may fix your issue (and may not...but it did fix mine.)
@ARTaudio440
7 ай бұрын
Hi, thank you for watching and for sharing this information 👍
@kelvinudoh4440
Ай бұрын
Hello I have same issues but on line 6 pod x3 live, how can I go about it?
@ARTaudio440
Ай бұрын
@@kelvinudoh4440 Hi, is the AC power adaptor that you are using for your X3 is original? Thank you for watching ☺️
@MartinEnriqueChavezMedel
6 ай бұрын
hola Allan, yo tengo 2 pod hd500 con la falla mas comun de este modelo. al momento de prender solo aparece el logo y vuelve a empezar el procedimiento de querer cargar el sistema. tu sabes algo de esta falla y como repararla? te agradezco desde Mexico
@ARTaudio440
6 ай бұрын
Hi, thank you for watching☺️ Let me check your message and get back as I don't have copy paste in my fone to translate your comments. I need to access it on my PC.
@AdamsAtseyo
3 ай бұрын
Hello sir my pod x3 line6 is not emitting any sound and has no display lights I don't know what to do please help me please
@ARTaudio440
3 ай бұрын
Hi, is your power supply original?
@AdamsAtseyo
3 ай бұрын
Amazing
@ARTaudio440
3 ай бұрын
Hi, thank you for watching ☺️
@lucaslinhares9697
6 ай бұрын
Hi! Greetings from Brazil. My unit is not showing the backlight of the LCD, please help
@ARTaudio440
6 ай бұрын
Hi, thank you for watching ☺️ For sure one of the LEDs is busted If the system works and only the backlight issue.
@ARTaudio440
6 ай бұрын
Or maybe a loose contact 🤔
@jerrychandlertube
Жыл бұрын
i got a fix for myself my power supply was kickn out 9.6 volts AC. apparently thats not enough mine is a older model, i have a Variac power supply. i turned up the power on the Variac until i had 10 volts AC. and it booted up with no problems.
@ARTaudio440
Жыл бұрын
Hi, thank you for sharing your experience and for watching ☺️
@frainreyes3316
2 жыл бұрын
Hello. I have a question. My hd500x has no sound output. Like, i can hear the one preset. But when i change preset it has no sounds. How can i fix this? Thank you for your response.
@ARTaudio440
2 жыл бұрын
Thanks for watching. Please watch this it might help. kzitem.info/news/bejne/k5ugvoOBsqSGq6Q
@kimonig9230
2 жыл бұрын
Hi Allan! Great video!... I have this problem... The volume goes up and down wile im playing... no knogs are touched... the volume changes by itself ... any help please? Thanks in advance!
@ARTaudio440
2 жыл бұрын
Hi Kim, Thanks for watching. If it is the rotary volume, one of the reason why it's happening because of oxidations. You must open the unit and apply a contact cleaner where available to purchased localy like in hardware or electronics store. Actually WD40 will works but my preferred is Contact cleaner where it drys immidiately. If you are talking about the pedal then try to calibrate it. Attached link for pedal calibration. kzitem.info/news/bejne/k5ugvoOBsqSGq6Q
@mukundagarwal6873
2 жыл бұрын
Hi I need a help My right side nav key sometimes stop working. It ks creating a lot lf trouble. Can you please help or share some video?
@ARTaudio440
2 жыл бұрын
Hi thanks for watching ☺️ If I have a chance, I will make it. Common problem for this model if there is issue on the sound is any one of the three ic is faulty. Its called DAC or digital to analog converter. Usualy if faulty, this ic gets hot or warm compared to good ic.
@marypaintedandrewportraits3113
3 ай бұрын
Hello! I'm looking to replace my LCD screen as mine has faded out. Is it just a simple unscrew and screw-on type of a situation? A video would help too. Hope someone can help!
@ARTaudio440
3 ай бұрын
Hi, thank you for watching ☺️ I would suggest bringing it to an authorized service center to make sure no additional damage. Replacing the LCD is a bit difficult to unsolder the pins due to the double sided board.
@DOUBLETHEFIST
3 жыл бұрын
I'm a little bit lost with this, is the sound output tied to the same component that was preventing the display from working? I have a unit that is getting no sound output but the display is working fine, should I follow the same steps you have here or should I be looking at something else?
@ARTaudio440
3 жыл бұрын
Hello thanks for watching☺️ Yes it's tied up because -15 volts is a VLCD of the LCD which is the LCD contrast pulse. Follow my trouble shooting in this video and focus only on the pre-amp supply. Try to check the supply of U18 which is pre-amp of the headphone pin4 +15volts and pin11 -15volts.
@ARTaudio440
3 жыл бұрын
If you gets +15 volts and -15volts meaning the pre-amp supply is good. Next to be check is the IC U40, U41 and U42 check this ic using your hand and feels if any one of these is getting more hotter than the rest. If gets hot, meaning that ic is the faulty one.☺️
@Makemoneyin6minutes
2 жыл бұрын
Wow...this is really so help full.thanx alot. I have the same pedal but mine doesn't light any of the foot switches it only lights white. Could you also help on that one!
@ARTaudio440
2 жыл бұрын
Thank you for watching. Try this sir if this will work. kzitem.info/news/bejne/k5ugvoOBsqSGq6Q
@ARTaudio440
2 жыл бұрын
If not It needs further diagnosing to check all the supply voltage
@MatheusOliveira2i2
2 жыл бұрын
my HD500x seems to be losing volume, the master starts to act from 3. in the calibration, the potentiometer seems normal. with volume at 4 I have an output voltage of 0.020mv. can you help me?
@ARTaudio440
2 жыл бұрын
Hi thanks for watching☺️ Try to calibrate the pedal. Pleas watch this kzitem.info/news/bejne/k5ugvoOBsqSGq6Q
@ronanquiambao4992
2 жыл бұрын
Hi sir my podhd400 is not emitting any sound but has a display and lights. IDK what to do sir, please help me
@ARTaudio440
2 жыл бұрын
Hi thanks for watching☺️ Have you done the pedal calibration?
@williamkelley10
Жыл бұрын
Sir patulong ng pod hd400 ko, no sound signal done reset,calibrating pedal,still no sound at all...kaya pa kaya ayusin?
@ARTaudio440
Жыл бұрын
Hi, possible po maayos pa yan. Focus lng sa supply +15 at -15 volts. Tska OP Amp at DAC ic.
@kevinshelly162
Жыл бұрын
Hi sir. I have podhd500.The thing is that when i am playing a preset, a * symbol will show in screen and volume comes down when playing. Also the master know didnt work well. From workshop, they told me it was IC problem and also told me that this will happen twice if i got repaired. I dont know what to do. Please help!😕
@ARTaudio440
Жыл бұрын
Hi, is it authorized Line 6 Service workshop? Please watch and try this video about the calibration of the pedal. kzitem.info/news/bejne/k5ugvoOBsqSGq6Q
@kevinshelly162
Жыл бұрын
No sir that was not an authorized workshop.. Can you please pin me your Instagram id please.
@ARTaudio440
Жыл бұрын
@@kevinshelly162 Please reach me here 👉👇facebook.com/ARTaudio440?mibextid=ZbWKwL
@upside-down6211
Жыл бұрын
I have a pod hd bean desktop,same problem with you,i accidently burn it by wiring the rj45 jack to the switch. No sound no display just blank white screen.I checked the preamp opamps and the inductor,right voltage but still not working 😢
@ARTaudio440
Жыл бұрын
Hi, If all reference voltages are complete then possibly some of the components were damaged because it was not a normal breakdown. I would suggest bringing it to an authorized service center. Line6 is under Yamaha.
@ClarenceFernando
Жыл бұрын
Hi Allan, there is a Line6 pod x3 live that is being sold on the fb with the same issue (no sound and no display). The seller's tech told him that the issue is the processor but upon watching this video I'm now having second thoughts if I'm going to buy it and repair it myself or not. The question is, will this fix work on that unit too? Haha. His tech might be right if the real issue is the processor. Is there a processor available in the aftermarket? Will it be fixed if the processor will be replaced? thanks!
@ClarenceFernando
Жыл бұрын
pinoy ka pala sir, nag-english pa ako, hahaha
@ARTaudio440
Жыл бұрын
Hi po. Ang common kasi na problem ng model na ito ay ic. Yung regulator na related sa video ko. Pag may missing na supply ay ganyan ang symptoms. Pero kung na check ng tech na meron o kumpleto ang supply ay possible main ic na ang sira. Pag main ic na ang sira ay di na sya ma rerepair. Board replacement na.
@ClarenceFernando
Жыл бұрын
Salamat sir sa info. Di ko na kinuha baka masayang lang arep, haha.
@hectorgenesta
Жыл бұрын
Hello sir greetings from Indonesia. Thanks for your tutorial but mine a little bit different problem. My LCD goes bright and brighten when I turn on my line 6 pod hd 500x. What should I do?
@ARTaudio440
Жыл бұрын
Hi thank you for watching. I have not in countered it yet, but please check all the connectors like lcd and wires.
@maxsuellima7488
2 ай бұрын
HI there, could you helpe me? My pod hd 500x turn on normally, but when I change a effect block after some time it reboots and start boot loop
@ARTaudio440
2 ай бұрын
Hi, if the new version is available, please update it and reset it after. Make sure also that you are using the original adaptor or at least within the specs. Thanks for watching ☺️
@maxsuellima7488
2 ай бұрын
Hi there, thank you for answering. I already try it 😢, but nonw of these things worked. When the pod self reboot sometimes it start a boot loop, but sometimes not. If it is on boot loop I need to unplug it and wait some time until it can boot normally
@ARTaudio440
2 ай бұрын
@@maxsuellima7488 For sure it has irregularities on the corcuit, possible loose connection of wire or faulty components like capacitor or crystal clock. I would suggest bringing it to an authorized service center. line6 is now under Yamaha.
@maxsuellima7488
2 ай бұрын
Would love do that. But generally it do not worth it, they will ask to change all board😢. But thanks for everything 🙏🙏
@ARTaudio440
2 ай бұрын
You're welcome!
@vishalsagar910
2 жыл бұрын
Sir my pod x3 live sound goes off whenever I touch the guitar input or output on the processor how to fix that can you please tell me I'm from India and i also wanted to know if I can get a footswitch replacement cause one of mine is broken and also the reading of original adaptor
@ARTaudio440
2 жыл бұрын
Hello Vishall, Thanks for watching.l It seems that there is a loose connections between the audio cable PL and jacks of Pod X3. Pleas double check the guitar cables then apply a WD40 to output and input jack of pod x3 and jack of your guitar also. I can't help you with regards on foot switch. I will suggest to bring it to an Authorized service center nearest you. Original AC adaptor can be purchased online or local with the same specs.
@vishalsagar910
2 жыл бұрын
@@ARTaudio440 Thank you so much sir but i dont know anything about electronics so can you send me your email id so that i can send you a small clip showing what going on with my processor.
@ARTaudio440
2 жыл бұрын
@@vishalsagar910 I do have a facebook page where you can reach me. facebook.com/ARTaudio440/
@stur34gt
3 жыл бұрын
I have the same problem with my hd500 but I have continuity and 9 volts at the part you resoldered , where do I go next
@ARTaudio440
3 жыл бұрын
Hello thanks for watching☺️ Do you have get -12V and +12V supply at Preamp IC?
@ARTaudio440
3 жыл бұрын
You must have +15volts on L59 and -15volts on L35
@stur34gt
3 жыл бұрын
@@ARTaudio440 I don't know where ic is but after watching your video and checking I don't have 12 anywhere
@stur34gt
3 жыл бұрын
@@ARTaudio440 I have 3v at l59 and 0 at l35
@ARTaudio440
3 жыл бұрын
@@stur34gt @stur34gt Check pin 1 of U49 not sure if 49 or 48 ic next o coil that I was checked and behind R306, you must have get +9volts supply on that pin. If +9volts is there and still the same, then you need to replace that IC. Beacause U49 ic is a supply of the preamp audio output.
@johnmali7412
2 жыл бұрын
Pod hd300 no sound output. Give me the fault finding way.
@ARTaudio440
2 жыл бұрын
Thanks for watching ☺️ Please check the voltages of the pre amp. If the voltages is complete, the fault is probably the ADC ic or DAC.
@johnmali7412
2 жыл бұрын
What is ADC ic or DAC
@ARTaudio440
2 жыл бұрын
@@johnmali7412 Hi, sorry for the late reply, I'll get back to you later☺️
@DavideZanellaDrum
Жыл бұрын
Same error on my HD 300. I'm going to check the preamp voltages
@ARTaudio440
Жыл бұрын
Hi thanks for watching ☺️ The voltages on the pre amp ic must be complet -15volts and +15volts
@promodgurung2515
10 ай бұрын
Hello brother, i have pod 500x...it is continously restarting and no buttons were working, but now its fine and every buttons are working but there is no sound...please help me..i have few gigs coming this december...it will be a great help
@ARTaudio440
10 ай бұрын
Hi, is the AC adaptor for your device being used is the original one?
@promodgurung2515
10 ай бұрын
@@ARTaudio440yes its the original one which i got with it...please sir, i need your help. what might be the problem..,?? By the way i used it after 3months..will that create some problem, like dust ..?? I tried other adapter also but it didn't fit.so no idea whether its a power supply failure or internal failure.
@ARTaudio440
10 ай бұрын
@promodgurung2515 Hi, I would suggest to let the authorized service center check. Such a case needs to be checked well.
@ayyink
Жыл бұрын
if the light on the screen is off, what is the problem?
@ARTaudio440
Жыл бұрын
Hi, Lcd has a backlight, 3 reasons if no light. 1 no supply 2 busted LED 3 Loose connection. Thank you for watching☺️
@ayyink
Жыл бұрын
@@ARTaudio440 thanks
@ayyink
Жыл бұрын
@@ARTaudio440 There are 4 Elcos that are swollen, does this affect the LCD lights, or is it the LCD lights that are broken?
@ARTaudio440
Жыл бұрын
@@ayyink Hi, I want to see it if you can send a picture to my FBpage facebook.com/ARTaudio440?mibextid=9R9pXO
@ayyink
Жыл бұрын
@@ARTaudio440 ok
@awesamos
2 жыл бұрын
Hi Allan. ive got an x3 live that has no audio. what could be the issue apart from the internal settings.
@ARTaudio440
2 жыл бұрын
Hi thanks for watching, Apply the pedal calibration on your Pod X3 live by keeping pressing the arrow right key while turning on the power. Please follow the screen message.
@awesamos
2 жыл бұрын
@@ARTaudio440 thanks for the reply. Did try that as per your instructions, yet no audio output. I did open the unit to see if I could get any further instructions.
@ARTaudio440
2 жыл бұрын
@@awesamos During calibration, numbers must corespond when you move the pedal. If it is not happening then the sensor or the two parts on the pedal sensor board requires a replacement.
@ARTaudio440
2 жыл бұрын
@@awesamos If you did it right the pedal calibration successful then try to have a look the supply of the pre-amp. +15 volts and - 15 volts.
@awesamos
2 жыл бұрын
@@ARTaudio440 calibration went well and succeeded. Numbers did correspond to the pedal movement. (Flashed “p” for passing the task)
@kuyamortv.8203
2 жыл бұрын
sir,, paki tutorial narin ng line 6pod live xt, bigla lang nag blankscreen sa katagalan na hindi nagamit
@ARTaudio440
2 жыл бұрын
Sure po pag may chance. Thank you☺️
@saniydel
2 күн бұрын
sir nka ranas k n ba ng podhd400 nag update ng firmware nawalan n ng audio?
@ARTaudio440
2 күн бұрын
Hi sir, hindi ko pa po yan na experience.
@carmichaeltv3875
5 ай бұрын
Hello po kuya allan..pano po maiiwasan yung bootloop problem sa hd500 or hd500x? madami kasi nakaka experience nyan sa unit na yan sad to sya yung iba di na talaga nagagamit. Same nung sakin.
@ARTaudio440
5 ай бұрын
Hi po, sa ngayon ay limited lng ang info ko kasi kung ano lng ma check ko at available ay un lng tlga. Advise ko ay gummit po lagi ng original power supply adaptor at iwasan mabagsak ang unit.
@carmichaeltv3875
5 ай бұрын
@@ARTaudio440 slamat po kuya sa sagot hehe
@ARTaudio440
5 ай бұрын
You're welcome 🤗☺️
@cap0976
Жыл бұрын
Ser, ask ko lang, yung POD 6 XL live ko bigla na lang walang sound, ano kaya ang problem?
@ARTaudio440
Жыл бұрын
Hi, sorry po kasi sa model na yan ay hindi pa ako nka check. Pero una nyo po e pa check ay kung complete ang supply sa preamp ic.
@cap0976
Жыл бұрын
@@ARTaudio440 ser meron syang display, sound lang ang nawala
@ARTaudio440
Жыл бұрын
Hi, pa send po ng picture sa fb page. Artaudio440. Di ko kasi kabisado ang model. Marami kasi volts sa circuit. Ang volt ng audio ay -15volts at +15volts. Sa system namn ay 1.2 volts, 3.3 volts at 5 volts.
@longtartisso2806
2 жыл бұрын
My line 6 pod hd 500x is having issues with the amp display, whenever i power on the line 6 it load its patch and after few seconds amp display pop up for second ?? And it come and goes for second Who to fix it Need help ??
@ARTaudio440
2 жыл бұрын
Hi thanks for watching ☺️ Try the global reset Turn on the power while holding down the arrow button left or right. If still the same Try it to update the sofware thru computer by installing line6 monkey apps or line6 updater.
@longtartisso2806
2 жыл бұрын
@@ARTaudio440 ok thank you and i will try and i will let you know if it works ❤️👌
@longtartisso2806
2 жыл бұрын
@@ARTaudio440 both Does Not work .. 😭
@ARTaudio440
2 жыл бұрын
@@longtartisso2806 Hi sir, sorry to hear that. I think it requires a deep diagnosing on your device. I would suggest to bring this to an authorized service center nearest to your place. Line 6 is under by Yamaha.
@matlesterdivinagracia6528
2 жыл бұрын
Hello po Sir may unit ako na Line 6 pod HD500 ayaw nyang mag Boot or Factory Reset tapos ang nkalagay sa Display ay Line 6 lang nkakainis pero wala akong magawa sana po matulungan nyo po ako.
@ARTaudio440
2 жыл бұрын
Hi po, salamat sa panunuod Subukan nyo po muna na e check sa computer gamit ang line6 monkey application.
@matlesterdivinagracia6528
2 жыл бұрын
@@ARTaudio440 Ok po update ko po kau.
@jsaravan
2 жыл бұрын
brother Allan, sakin naman mag on pero hindi mag start yong screen lang with the line 6 logo. ayaw mag start. may idea ka ba please let me know bro. salamat
@jacgelacousticduo6132
2 жыл бұрын
sir...yung podxt live ko poh..walang sound sa output po..pahelp po
@acearagones130
8 ай бұрын
Sir yung sakin ayaw magconnect sa pc ano kaya possible problem ? Kahit updated na yung mga driver uninstall at install ulit na ginawa ko ayaw parin eh salamat sa sagot sir 😊
@ARTaudio440
8 ай бұрын
Hi sir, na try nyo na po mag install ng Line6 Monkey bukod doon sa software driver ng pod hd500x?
@acearagones130
8 ай бұрын
@@ARTaudio440 ou sir nagdownload na po ako nun autodetect siya ng model diba sir kasi yung hd400 ko nadedetect niya agad pag sinalpak ko pero yung 500x ko ayaw niya
@ARTaudio440
8 ай бұрын
@@acearagones130 So far di ko pa na encounter ang ganyang problema. Pero suggestion ko ay mag try ka ng ibang usb cable at ibang computer.
@jsaravan
2 жыл бұрын
mine doesn't start, the screen is on with the line 6 logo on it🥺
@ARTaudio440
2 жыл бұрын
Hi, try it to connect with the computer by using the line6 monkey application for software update.
@jsaravan
2 жыл бұрын
@@ARTaudio440 ok bro maraming salamat subukan ko.🙏
@linobacarro6875
Жыл бұрын
Ano causes ng mejo nag fi flicker yung LCD lods?
@ARTaudio440
Жыл бұрын
Hi po, di ko pa na encounter yan idol pero posible po ay loose connection ng port ng lcd para sa backlight or yong backlight na mismo ang problema.
@linobacarro6875
Жыл бұрын
Kasi dito sa service center hindi sila gagawa ng mainboard issue, replace sila agad. So far di naman affected ang sound na.
@ARTaudio440
Жыл бұрын
Yes idol, ganon tlga sa service center
@linobacarro6875
Жыл бұрын
Taga san ka lods?
@ARTaudio440
Жыл бұрын
Taga Romblon po idol😊
@123sssrrr
2 жыл бұрын
sir paano pag gumaralgal bigla ung sound?
@ARTaudio440
2 жыл бұрын
Hello po sir, Pag ang issue po ay sa audio ay unang una kung merong abnormalities na supply sa pre-amp, pangalawa ay sa DAC ic or digital to analog convertion tapos loose connection sa audio output.
@123sssrrr
2 жыл бұрын
@@ARTaudio440 bigla lang kanina sir eh, san po b aarea nyo sir at pagawa ko sa inyo?
@ARTaudio440
2 жыл бұрын
@@123sssrrr Nasa abroad na po ako sir. Original na adaptor po ba ang gamit nyo?
@123sssrrr
2 жыл бұрын
@@ARTaudio440 aww sayang, hirap kasi maghanap ngayon gawa ng lock down ulet, orig adaptor po gamit ko
@jacgelacousticduo6132
2 жыл бұрын
baka may fb page ka sir
@ARTaudio440
2 жыл бұрын
Hi, thanks for watching idol Meron akong Fb page. ARTaudio440
Пікірлер: 164