Thank you for sharing! Especially the body filler technique and the fact that you shared your knowledge of sand paper grit size by doubling it at each stage. Love it! Thanks you!
@gregoryarron1130
Жыл бұрын
This is a great video for novice painters. I had my Jeep painted my a so called pro and I have so many runs in my paint and now its up to me to fix it. I appreciate you kind sir.
@hoodatdare7039
4 жыл бұрын
I PUT MASKING TAPE ON BOTH SIDES OF THE RUN THEN SHAVE IT WITH A SINGLE EDGE BLADE. AND USE THE 3M WET SANDING BLOCK KIT
@mangkanorth
4 жыл бұрын
If you're able to replicate it, you can fix it. Nice way of educating newbies.
@TrojanHorse1959
6 жыл бұрын
I use a NIB file, or use a single edge razor blade and wrap a bit of tape around each side leaving only a small spot in the middle of the blade exposed.
@tranzco1173
4 жыл бұрын
Thanks you for this tip, I restore vintage furniture, and tried this and it worked great
@MultiRanger90
6 жыл бұрын
Hello, I learned a lot about this videos. Its great how you explaine things about spray painting. In the past i made a lot of mistakes, but now thanks to the videos i feel more confident in painting stuff on my car. A great channel, Big thanks from germany
@EssexSilvering
3 жыл бұрын
I don't often get a run in my paint but if I do I use a hair dryer to push the run to the egde and get rid of it that way ;-)
@EnricoMiggino
6 жыл бұрын
don't spray paint if it's too windy..
@JamesSmith-lt5zz
5 жыл бұрын
If you can't wait get closer to the panel but move quickly with it. Much easier to do this with a spray gun then can.
@Pocketchangesilvaerado
Жыл бұрын
That’s why I searched for this video😅😂
@stevenlane729
5 жыл бұрын
Fantastic tutorials, I love your teaching technique. Thank you
@jackskeleton95
7 жыл бұрын
temperature can also affect whether you get runs or not since paint doesnt dry in the cold as fast
@Iheartdgd
6 жыл бұрын
Correct, and I’d hope any painter would know that >.
@JamesSmith-lt5zz
5 жыл бұрын
I can tell when the seasons change. In the summer I have to hammer it on. 110 degrees with 90 percent humidity. When it starts cooling off I'll start getting runs. Have to dial it back and go to smaller tips. When its really cold 40 50 it'll look OK then when you make it back around for the next pass 20 30 mins later it start running. Take it easy in the winter and do a thin tack coat. And I'll use a heating pad to heat the paint and hardners on
@loyalroyal146
3 жыл бұрын
@@Iheartdgd j KK
@loyalroyal146
3 жыл бұрын
My Kum;;; Umm
@loyalroyal146
3 жыл бұрын
My Kum;;; Umm
@MrAudi220
4 жыл бұрын
Well thank you so much for explaining this properly, i had major runs on one side because that side of my trunk lit had been sitting in the sun,so today i spend a couple of hours applying putty and sanding it down with 320 wet,and it's almost entirely gone,just need to finish off tomorrow with the 320 untill it's completely flat and then starting to work my way up in sandpaper to remove the scratches and then safe some money to buy a polisher and some buffing compound.So big thanks again, it's my very first paint job at home and the results are quite amazing,i'm doing all this with a lvlp gun, and i can highly advise this type of gun for anyone starting out.👍✌️👉
@tonygreen3528
3 жыл бұрын
Sandpaper, you mean wet and dry paper,
@abruptlyblunt
2 жыл бұрын
i had forgotten how good your tutorials are...
@freeelectron8261
5 жыл бұрын
Paint guru has many solutions for the dread paint run! I will try them out to solve my dread paint run. Thank you sir!
@georgechecker9262
3 жыл бұрын
excellant demo, very clever, patience a must when doing this, most helpful
@damincobozeman8921
3 жыл бұрын
Great tip and video! I didn't know that I'm almost finish collision repair school at Lincoln tech and you just showed me something I haven't learn! Thanks keep on teaching!
@SebastianBurdon
6 жыл бұрын
This is very helpful even for spraying small items.
@Skipdogg15
3 жыл бұрын
While the clear is wet, lay a piece of tape on the run, run your finger over the tape where the run is then pull the tape off, wait for the clear to flash some. Put some more clear on then the next day all you have to do is cut it a little and buff. Good as new 👌
@adventuresofsven2314
2 жыл бұрын
Awesome advice thank you so much for sharing your tip
@immortality22
7 жыл бұрын
excellent video mate....definitely the sanding gets the job done perfect. thanks for making this video so detail...keep it up mate
@GLC2013
Ай бұрын
Whooee, that is one good lookin' fellow. Great training video and very helpful info as well. Thanks!
@shaharzadshahee2297
3 жыл бұрын
That is such a GREAT GREAT video dude. Its almost 10 videos i watched before yours in 1 and very brief , to the point and clear!!!
@iamrocketray
2 жыл бұрын
I like the fact that he had to TRY to get a run, the guy is so good that he had to deliberately engineer the run.
@marcuswhite1403
Жыл бұрын
I'm so good, I can get a run with my eyes closed lol
@corvettec8miamiracing259
4 күн бұрын
THANK YOU FOR THE TIPS.
@sergiofuka
4 жыл бұрын
Subscribed. Theory + Practice = Real Knowledge.
@zigzagduck952
6 жыл бұрын
Ever considered using a small hand held drill with a detail sanding tip. Something like a Dremel. Seems that this might be a faster way to remove dried runs.
@foxybrown2
6 жыл бұрын
You forgot one other way that i learned from Allkandy you can mark it with a magic marker as a guide coat.
@jhenson5168
2 жыл бұрын
Forgot about residue on the substrate. Sometimes it's inevitable. Humidity plays a big part in runs as well. I'm spraying right now at work. Industrial painting, no "paint bay" or climate/humidity control in oily greasing beams of steel. It happens.
@robertgarcia9011
7 жыл бұрын
thank you because I'm new at this as you can tell and some of the videos I've watched really don't ever give me any answers so thank you
@bronxicon88
2 жыл бұрын
Thank you for the video it really helped me out a lot. Much blessings to you 👍🏼
@lanaz8923
6 жыл бұрын
You sir have taught me a lot you are indeed a great teacher thank you so much
@snitz157
7 жыл бұрын
Congrats on 100k subscribers Dave!
@customspraymods
7 жыл бұрын
CS Studios thanks mate. Thanks for always watching and commenting. Every like and comment good or bad drives me to make more.
@mafiaperformance
7 жыл бұрын
customspraymods check out my comment.
@mafiaperformance
7 жыл бұрын
customspraymods please answer it
@customspraymods
7 жыл бұрын
Done.
@JW-kp1lp
7 жыл бұрын
Tungsten blocks have come along way bro...not just your standard square ones anymore. I swear by them. especially the cheaper CRS brand ones. Those and a razor blade with the corners taped up are my go to methods. Cheers mate. Edit. I do understand you are making these videos for peeps who may just have basic tools. But tungsten is the bomb.
@mrad907
6 жыл бұрын
I was the king at getting runs, I found you can round off the corners of a new razor blade using some 600 wet/dry paper to scrape away runs
@victorg530
5 жыл бұрын
Very clever thanks! One question.. what's the benefit of using plastic filler?
@tonop455
3 жыл бұрын
Put "pepto bismol" in your gun and spray to get rid of runs. 👍
@chieflongsock
5 жыл бұрын
How about a run in the paint...not clear coat
@overmarsdaria3222
4 жыл бұрын
What about fixing a run from paint ,not clear coat! I tried to fix it with 1500 sand paper and polishing afterwards but the colour fade into a darker patchy shade.
@shaharzadshahee2297
3 жыл бұрын
I think base coat is matte so if you havent layer clear yet then just sand it to make it even and spray a coat of base again?
@ezequielmedal9547
7 жыл бұрын
SPRAY MY TRUCK!!!!! LOL GREAT VIDEO BROTHER!!!
@madmattdrummer5487
5 жыл бұрын
What if the run is from the paint and not the clear coat
@intraw831
4 жыл бұрын
Mad Matt Drummer it’s hard to run basecoat, all you need to do is sand that run out then spray the area you sanded
@archiethree
7 жыл бұрын
Well Done Dave Great Video
@randomnetizen7065
7 жыл бұрын
sensei...thanks for the guide..help me alot
@superchile9640
3 жыл бұрын
Great tutorial. Made a subscriber. Thank you.
@__MAT__
2 жыл бұрын
Excellent content, as always. Thanks fer yer time.
@apostate4apostate494
3 жыл бұрын
Lol “sand without touching the area around the run” > sands the entire side of the panel. Lmao
@igorposlin173
3 жыл бұрын
Well you do have to fether it out, can't just sand one spot and polish it afterwards, it will leave a indentation
@steveguest8028
2 жыл бұрын
Great video…. Thanks Dave 👍
@772777777777777
7 жыл бұрын
You should make a video on a test hood showing how psi effects and reducer temp effects Orange peel
@customspraymods
7 жыл бұрын
henri I have touched on that mate check this one out. kzitem.info/news/bejne/lpyE2oWFnHp1e4o
@772777777777777
7 жыл бұрын
Thanks I watch the video, But was hoping someone had a video showing a hood masked off in several area showing how a poorly set up gun ie fan pattern effect orange peel with the combination of psi from a low 26 psi to know higher psi which eliminates the orange peel... I keep hearing clear coat should be sprayed at 29 psi with HVLP, I like to know what psi should be use with HVLP gun. Can you make a video with different psi setting ie 26, 29, 35, 40, 50 psi masked off on a test panel and show the effect of low and high psi
@772777777777777
7 жыл бұрын
as well as adding reducer to the clear coat ie final coat to flatten the clear coat on the last coat
@hfromdy
7 жыл бұрын
your a great guy, subscribed and very good videos i would love to learn how to spray paint like this
@abdallahmk3694
6 жыл бұрын
Hello dear, Kindly tell me the types of polisher used in order
@MartinParoubek
7 жыл бұрын
Great job again! Nice vid!
@3dprintwiz378
6 жыл бұрын
Hi, will this also work when you have a run on the paint itself not clear coat? Nice vid by the way.
@XBKLYN
10 ай бұрын
Yep....we all get the runs from time to time!
@Ka_Gg
5 жыл бұрын
Thank you for these tips! Awesome!
@Nismology33
4 жыл бұрын
Great job and very helpful!!!
@markalious
7 жыл бұрын
im watching all of your videos, its really usefulk
@chuy28851
7 жыл бұрын
Wow good job bro
@olivaguitars4926
7 жыл бұрын
Thank you very very much for your videos, but pls buy a mic
@ryanm2084
5 жыл бұрын
I can hear him just fine
@bobsmyth7590
5 жыл бұрын
T Y I have a truck tailgate to do- 2 runs-- poor lighting & the mix- thanks again
@danielwillmott6485
3 жыл бұрын
Good video like the filler trick bit risky for me lol I use a mirka shark blade works treat on uhs and HS clear
@gearupsylhetypubg1816
4 жыл бұрын
Thanks for your this video. I learned that 1. It will be helpful 😊😊
@ericgrajeda2671
11 ай бұрын
The filler and sand it down is a good method yet might take awhile .
@arbythepainter
3 жыл бұрын
I have the runs too but I have a suspicion that burrito from last night caused it.
@louisborg818
7 жыл бұрын
How hot was it in the room your in? Every cut scene you were sweating more and more😂😂😂😂
@customspraymods
7 жыл бұрын
Louis Borg 40 degrees C mate.
@Wipsplash
6 жыл бұрын
Every time I run my paint, I sweat too!
@johnbraucher1499
5 жыл бұрын
@@customspraymods 104°, does that effect your paint in a negative way?
@JamesSmith-lt5zz
5 жыл бұрын
@@johnbraucher1499 you need more paint in higher temps to keep that wet edge. As soon as its hits air being atomized it's starting to dry. To far back makes orange peel and dry spots the paint is dry before it hits the panel. In cooler temps you use less paint per pass it flashes slower. Different thinners can help with flash times.
@joseandresgiron6445
7 жыл бұрын
can you make a vídeo about how to polish? thanks
@bobcannon5217
7 жыл бұрын
jose andres giron There's an old old old video they did on polishing
@kityenna9839
4 ай бұрын
“ I got a run here.. that’ll ruin your day” Me: on day 2 of having runs on my tank with my day ruined
@natusxc9733
5 ай бұрын
Hello i jist wanted to ask, can you paint it with clear coat after you sand it?
@lucianosantucci108
2 жыл бұрын
Excellent 👍
@thecryingghast
7 жыл бұрын
Colours of the week is what I miss
@MatthieuLibeert
7 жыл бұрын
good video, thanks! istead of using bodyfiller you could use some masking tape as well to avoid sanding the area you dont want to sand right?
@customspraymods
7 жыл бұрын
Matthieu Libeert that may work. Sometimes you may have more than one run but a whole line of runs. Using tape might take forever to mask.
@Wipsplash
6 жыл бұрын
Tape doesn't work well. Gums up the sand paper.
@newjsdavid1
3 жыл бұрын
Came out swinging with the big guns
@kirkwalter9879
2 жыл бұрын
I sprayed a desk top and I can see the lines where I sprayed after 3 coats. It's drying funny or something. How can I fix it?
@arthebulletandyamahafactor731
2 жыл бұрын
Great sir Thanks
@ForestWoodworks
Жыл бұрын
Nice! Thanks! 💯
@KurumaDesigns
7 жыл бұрын
Great video! Thanks!
@jeffg377
7 жыл бұрын
Awesome video ! What do you do if you get a run in your base coat ?
@customspraymods
7 жыл бұрын
Jeff G let it dry. Then sand with 800g wet. Scuff the rest of the panel. Clean and apply more base coat
@jeffg377
7 жыл бұрын
Thank you for answering my question so quickly and you're awesome and I love your channel .
@NicholasMuscat-cl1qo
Жыл бұрын
I have a medium to small sized run I cant get the wave out doing this, I'm certain I did good body work any suggestion?
@snail415
3 жыл бұрын
Legit as the finger snap.
@adot111
11 ай бұрын
Hi, is this paint run from clearcoat? what should I do if during the paint, I found the paint run before clearcoat process. Thanks
@Richie4027
5 жыл бұрын
thanks man you got skills
@Shedmaster-ng1ik
9 ай бұрын
You should retitle the video how to prevent and fix runs in clearcoat. Does not go over how to fix runs in PAINT
@darrenbaker2171
5 жыл бұрын
Nice trick with the filler 👍
@romamreigns9971
6 жыл бұрын
Good job sir
@Kr0n3kLe
2 жыл бұрын
I tried the crap load of clear and it made multiple runs. What could I do next
@jdmchickkustomz9417
2 жыл бұрын
I repainted my car about a month ago now and I've got some runs in it and dirt so now I need a wet sand it and buff it. Any advice on what grit to use on the runs?
@mohammedwaheed6979
Жыл бұрын
Its a great video
@williamwalter9074
5 жыл бұрын
While it is wet use masking tape sticky side touch lightly
@SuperAwsomeBanana
4 жыл бұрын
probalbly late but i got runs on the primer, just to wet sand it a little? also when putting decals on a motorcyle fuel tank, , is it better to put them on the metallic paint or a layer of clear or two, then let it dry and then put two more layers of clear over the decals?
@AaronUnknownPerformance
6 жыл бұрын
Brilliant
@justinmarder484
4 жыл бұрын
if i am using the sandpaper wrapped around wooden mixing stick method, what sandpaper grit should i use? i was thinking about using 1000 or 1500 or 2000 but i have no idea. Should i use multiple grits? also if i then re clear the panel, will i have to sand the whole panel or that is not necessary
@ronbusa3735
4 жыл бұрын
Great info Thanks
@uwu-nr9mh
2 жыл бұрын
you’re awesome!
@rustygood6336
10 ай бұрын
What compounds and pads do you use?
@Rickymorales1
4 жыл бұрын
What brand fine filler did you use for getting the runs out? Is "evercoat glaze 417" the same thing?
@goos5224
5 жыл бұрын
Did you mix the fine body filler with hardener and let it dry ? what kind of foam pad did you use?
@andrecarrosserie6966
3 жыл бұрын
Nice video usefull !!!!!!!!!!
@renegomez6456
5 жыл бұрын
how long after spraying the clear and get a run are you safe to apply the filler?
@b-two-4427
7 жыл бұрын
good ! thanks 4 the steps..
@3rekoatskustoms145
7 жыл бұрын
Great video wud u use body filler on any run or just small ones
@customspraymods
7 жыл бұрын
3re koats kustoms anything even big ones.
@splash5974
6 жыл бұрын
Dont use regular body filler... too hard to sand. Use a 2 part glazing/body putty. Much less effort
@mafiaperformance
7 жыл бұрын
The video you painted the candy fender. What did you use to separate he colors. Some type of black tape maybe? I asked in that vid too.
@customspraymods
7 жыл бұрын
Tony Bersaglia replied on the video mate.
@mafiaperformance
7 жыл бұрын
customspraymods I saw! Thank you so much! Now I can move forward on my helmet!
@NightfoxSD619
Жыл бұрын
"If you notice the run is gone" as clearly still a run on the panel ...
@FairUse138
3 жыл бұрын
Very helpful
@dioumanjaved1548
7 жыл бұрын
great vid
@j.l.160
7 жыл бұрын
shout out from suriname! take me as a student please
Пікірлер: 293