Wow, you really saved my printer. Thank you so much for that wisdom :) I wish I could help others as much as you someday!!
@GTCSRobert
2 жыл бұрын
Thank You Paolo. I followed these steps and my C460FW is now working. I can't thank you enough!!!!
@aldosvampa8630
3 жыл бұрын
Thanks Paolo, The video is very good and clear, greetings from Argentina.
@alanboro
3 жыл бұрын
READ THIS IF YOU DON'T WANT TO PURCHASE A NEW SPARE PART: There is a %90 reason why the solenoid does not work, and that is the little rubber piece that acts as a "stop" of the spring loaded metal piece is "crushed". It has become so thin that the metal piece has not sufficient space for the electro-magnet to work. To fix this: - Follow the tutorial up to the point where he just replaces de solenoid. - Instead of replacing it, grab a piece of two sided rubber tape, or a piece of a rubber sandal or something and paste it between the previous rubber piece and the moving metal piece. It should be very thin, you don't want too much space either. - Re-assemble as the tutorial shows. On another note: my C410w model (Argentina assembled model) has some differences that made working on it a little more difficult than the video: - They replaced some cables with ribbon cabling on the main pcb board, that prevented me from totally flipping the board to remove the loading tray screws. It was nerve wrecking to try to push the pcb board and remove the screws without em falling. - There is one extra screw to remove the loading tray, which is silver and is exactly below the first black screw he removes in the tutorial. THANK you very much for this video!
@PaoloMarcelli
3 жыл бұрын
I've made a video about these solenoid problems even on other Samsung printers where I just replaced the rubber pad, but when I tried this method on this model it didn't work for me, so I ended up replacing the solenoid :) but maybe was just a coincidence for me, sure better try this before ordering the spare part! Thank you for sharing your experience.
@weigefans
28 күн бұрын
great video to demostrate the reason why happen the issue, also great solution to fix it! great!
@elenafedeli
Жыл бұрын
@lennertheilmann8474
2 жыл бұрын
Thank you for the great tutorial! After 8 years of service, my Samsung C410W would only take in the paper half way and then get suck on the first print-job. I always had to pull out the paper and restart the printer to make it work properly again. I removed both pieces of rubber from the solenoid and replaced them with some rubber from a bicycle tube, which I attached with double-sided adhesive tape. Now the printer works like new.
@gerardlapierre2820
3 жыл бұрын
Many thanks from Paris. Everything works after having changed the solenoid.
@parmmohan4603
3 жыл бұрын
Same. Just changed it last night and works great!
@wongdiggy
7 ай бұрын
Wow, it is such an informative video. This fix gave my printer a second chance in life. I had to watch and rewatch it a few times. There were some tips missing like getting the front panel off and using a swiffer dry static wipe to clean up toner, but this nailed it so well, I could not express enough gratitude for you posting the how-to repair video. It's thankfully not too difficult.
@bb7743
3 жыл бұрын
Paolo, your video was great! I would never been able to diagnose nor fix my C460FX without it! Your instructions were perfectly detailed--I watched your video before I started the repair, and then watched it again (with lots of pausing!) as I stepped through the repair. I did not replace the solenoid, but like others, but put a mylar label on the rubber pads to prevent sticking (even though the pads did not seem to be breaking down). I crossed my fingers and it all worked after I put it all together. The repair took me about 2 hours in total--I wish I was as proficient as you. Thanks again for this great video! Bud
@PaoloMarcelli
3 жыл бұрын
Thank you bud, great job :)
@DarioFoley-qu8ns
Жыл бұрын
The printer was a bit complicated to hook up kzitem.infoUgkxciSwynMJ7PnUvvx11rewiu-yFBkZTl53 but it does the job very efficiently. I like the ink wells versus the ink cartages that cost an arm and a leg. It prints quickly and the quality is excellent. It shuts off when not in use, so you have to remember to turn it on. Overall, it exceeds my expectations. I'll update my review in a couple of months.
@robertmeert9564
3 жыл бұрын
A big thank you for this very well detailed tutorial. By following these explanations, I was able to repair my printer which will take on a second life.
@hermesnetwork
Жыл бұрын
Thank you so much for the detailed video tutorial. I was able to follow your instruction and fixed my Samsun C410W printer pick-up issue after replacing the JC33-00025B Solenoid. You're great and I'm very grateful for your help!!!
@dearme5660
Жыл бұрын
Thank you! This was very easy to follow step by step procedure, and it has a very detailed explanation.
@acewindbreaker
Жыл бұрын
I want to thank you for this excellent video! I have the C410W version and it didn't pick up the paper, and just as you described, when I used a flashlight to look into the printer I could see that it stood still inside. I found a solenoid on a websight in China, and ordered it from there, the cost was redicolous, about 8 Euros including getting it in my mailbox. Following your instructional video it was quite simple to change the solenoid, and after putting it all together again, the printer worked perfect!! So once again a big THANK YOU!
@nicolaschiaruttini8450
Жыл бұрын
Awesome, you saved my CLX-3305W for 5 bucks, and a bit less than one hour of work, thanks to your perfect tutorial. There's just one tiny thingy stuff on the right that needs to be pushed when removing the front panel on my model (at around 5:21 on the video). I followed exactly the tutorial and found the new solenoid on digitec (article JC33-00025B, it took a few weeks to arrive).
@nicolatompkins6517
2 жыл бұрын
Thanks for the video. It helped me change my solenoid sensor and now my printer is working perfectly. 👍
@AndrewFrance
2 жыл бұрын
To add to the chorus, thank you so much for this video! Our Samsung CLX-3305FW has been having trouble picking up paper for years, leading to much frustration, until last week when it finally totally stopped! Thanks to the other comments here I didn't try to remove and replace the solenoid but simply removed the lower pad and taped the lower and upper areas with a tiny amount of electrical tape. I hope Samsung have rectified this design issue in newer models as otherwise the printer is pretty good and I'm impressed at the repairability.
@jwilkinson341
2 жыл бұрын
I got it off there were inner ones close to the middle, I put it all back together and it works I had my doubts, many thanks for this detailed video
@fabiomarcon555
3 жыл бұрын
Hi this helped me a lot even though I don't have the printers above I have a clp-315w the solenoid thankfully it is a little bit easier to get to and it was sticking because of the pad - removed the pad _ DONT NOTIC ANY DIFFERENXE IN NOISE and it works fine
@bnenm9310
3 жыл бұрын
Worked for my Samsung C460 too. For just one 4$ part such a procedure. Thanks for you video, helps a lot.
@andersjonsson1874
2 жыл бұрын
Thanks! Did this on my C460w. I also lubricated the tap on the inner gear wheel to reduce the friction between solenoid arm and the gear wheel. I removed the little top foam piece and replaced it with double adhesive foam tape but left the top plastic on the tape stay on. Worked perfect after 2 years of fighting this printer and almost giving up.
@marcofebbo4096
Жыл бұрын
so, is the solenoid on the alibaba link compatible with C460W?
@graphicad-COR-2579
Жыл бұрын
Excelente video, me ayudo a resolver el problema de mi impresora. Muchas gracias por tu ayuda.
@detjuk
3 жыл бұрын
Great video, cleaning didn't help, but replacing the solenoid seems to have fixed the problem! Mine is a clx-3305fw from Samsung. Replacement part orderd on aliexpress.
@marctre1
Жыл бұрын
Thank you, my printer has been inactive for more than a year because of this problem. Took me about an hour and now it is working even better than before it broke (it gave errors about having to change the imaging unit and now it doesn’t). You’re awesome!
@PaoloMarcelli
Жыл бұрын
Thank you :)
@BernatLlorenç
10 ай бұрын
Great step by step tutorial. It allowed me fix my clp-365w printer. Thank you very much Paolo! 👏🏽👏🏽
@jorgsteinke1140
3 жыл бұрын
Awesome! Thank you so much for this detailed and handy video. I fixed my Samsung CLX-3305FW with this guide.
@PaoloMarcelli
3 жыл бұрын
Great job! :)
@zozzo58
4 жыл бұрын
Just worked perfectly on my CLX-3305 : thank you
@PaoloMarcelli
4 жыл бұрын
Thank you for watching and now throwing away your printer :)
@lwcmy
3 жыл бұрын
Thank you for your sharing. You saved my printer with a small spare part. My printer is C480W, slight different structure but your guide is adequate for me to repair mine.
@davidng9354
3 жыл бұрын
Hi Wee Chang, my printer is same model as your. Is the solenoid part no. you purchase is using same as what he recommended?
@lwcmy
3 жыл бұрын
@@davidng9354 ,yes, i bought from here: www.aliexpress.com/item/4001143446682.html?spm=a2g0s.9042311.0.0.16b84c4dhReECs
@kristian.gustafsson
3 жыл бұрын
Thank you! You saved the life of my CLX-3305. I can now print again after 1,5 year 😊
@PaoloMarcelli
3 жыл бұрын
Great job for fixing your printer :3
@bartekpaluch4474
3 жыл бұрын
Thanks for saving my time and money. I have only disassembled, touch the solenoid couple of times, and assemble it again. My printer was resting for like 2 years so maybe it just wanted a little touch... Thanks, good job.
@CpaMoya
2 жыл бұрын
Paolo. La impresora no tomaba el pepel, estaba pensando en botarla a la basura. Encontré tu video, y la verdad, es excelente. Te agradezco por la claridad y exactitud en cada proceso. Ahora puedo seguir usando la impresora. Me ahorraste de comprar una nueva. Muchas gracias y saludos desde Santiago. Chile.
@PaoloMarcelli
2 жыл бұрын
😊
@nemethzsolt5245
3 жыл бұрын
Thank you the video! I take out the solenoid from the printer. I measured the solenoid with DMM, but the solenoid is good. The solenoid connector is the wrong (I cut the solenoid wire next to the connector and soldered it to the panel)!
@jayanour
4 жыл бұрын
Wow! Thank you very much for your life-saving video. I know now what to buy to fix my printer. It seems that the solenoid is a common problem for Samsung printers. Keep up the good work and stay safe.
@sjakob52
4 ай бұрын
Hej Can you advice me about Samsung print plugin for wifi. I have fixed an older clp 365w with usb and wifi direct. When using my phone I specify pages to be printer but it dosen't a cept single page definition, and also intervals are interupted with green light blinking, and fuser heat up. I have used Samsung print plugin before on other versions of Samsung cpl 365w where it worked proberly. Can you help?
@DeltaBlast
Жыл бұрын
This video was very easy to follow and allowed me to replace the solenoid in my CLX 3305FW. However, when I put everything back together, it didn't turn on any more. Just nothing on the display at all. I've retraced all the steps and did it all again, but I don't know what went wrong. Maybe I damaged the logic board? Do you have any clue what would cause the display to not come on at all? I even put back the old solenoid, but that wasn't the issue either. I opened the cover for the electrical parts but I didn't see any popped capacitors and that's the extent of my knowledge... Any help would be appreciated!
@oldengguy
Жыл бұрын
Thank you. I just picked up a CLP-365W marked $7.99 at a thrift store, and it has the same symptoms. Everything else installed properly. Your video has convinced me I can open this up and do this. I'm guessing it will be exactly the same problem.
@PaoloMarcelli
Жыл бұрын
You can definitely do that :) also other users said that in their experience it's not needed to replace the entire solenoid, just the two foam pads :)
@oldengguy
Жыл бұрын
@@PaoloMarcelli I pulled out the solenoid, checked to make sure the resistance was right, and worked with it to make sure it was clean and free and that those pads were not sticky, put it back in place, and the printer is working great. It didn't cost anything except a bit of time.
@elenafedeli
2 жыл бұрын
Sei un grande! Mo ordino "the infamous solenoid" e speriamo di recuperare sta stampante C430W che ho davvero troppi toner per buttarla via ora.
@PaoloMarcelli
2 жыл бұрын
Brava :)
@keyvanjavan7141
8 ай бұрын
Wow... thank you man... you are amazing❤❤❤ i could repair my printer❤❤❤❤ thank you thank you thank you❤❤❤
@PaoloMarcelli
8 ай бұрын
Thank you for watchign and saving your printer :)
@keyvanjavan7141
8 ай бұрын
@@PaoloMarcelli I have a question. Is that electronic part that you replaced common among printers? Can it be taken from another printer and used to repair a broken printer? Do you think other companies use the same part?
@gianniint8874
11 ай бұрын
Grazie per questo video fantastico. I tried to disassemble and just cleaned the solenoid without taking it out and re-assemled the printer (C410W) - Proble still persists but at least I have familiarised with the procedure. I will have another go at trying to fix the solenoid with rubber or something similar before I look for a new part. The JC33-00025B somebody mentioned here seems to be reasonable in price (+£ 6-7 for postage) but not sure it is the correct one. Will post back in due time. Grazie ancora Paolo. Giovanni
@izmirtoner
Жыл бұрын
dear sir , may u show where is this part on samsung 2675f thank u.
@PaoloMarcelli
Жыл бұрын
Hi :) I'd like to do that, but I don't have that model of printer to make a video on it :/
@apantrasansson
Жыл бұрын
Good video! I have a 430W. The diagnostics report no problem. But the printing software claims that the "lid" is open. I previously got two error codes from it once - m1-1013 and m3-112.Still, it prints test documents pressing the "X" button just fine, just like you did to test the solenoid. But when I try to use it for printing anything else, it refuses. It does not even try to pick up paper. Just silent. Any guess to what might be the problem?
@ugurr5301
3 ай бұрын
Hi, seems I'm the lucky one in which the printer is returning an error. I followed your awesome guide step by step, replaced the solonoid and put everthing back together. I'm now getting the following problem; printer boots up, little bit of spinning sound and then it goes to orange led. If i try printing i'm getting an error on macos with message 'imaging unit failure'. Before I started with this fix the printer would show green led, but wouldn't pick up the paper. Could it be that I put the solenoid in a wrong way and thats why i'm not hearing the spinning? Would be great if anyone could help, I feel like the fix is easy and I don't want to throw away the printer :((
@quasimali1255
3 жыл бұрын
just what I needed, thank you! Worked perfectly
@kjaxky
2 жыл бұрын
great job! What's is the difference between Samsung CLP-360/365W, C410W/C430W they'll look the same I know 410w/430W were sold in usa and canada but I cannot figure out differences at all
@sjakob52
7 ай бұрын
Hi Paulo. The tip of the paper is graped by the pick up roller and the printer stop emmidiatly with yellow blink. I can pull the paper out with easy draw. Do you think this is a solenoid problem or something else?
@jorismk1
Жыл бұрын
Thankyou! What I did was use the old coil. It's not broken, just the pad is compressed and somewhat sticky. Remove the pad and clean, bend the metal lip to where the pad would normally stop the arm. Reassemble and done :) Only thing is it now clicks when printing (which I don't mind)
@ziaurrahman8729
2 жыл бұрын
Hi Marcelli, I am having problem with my printer Samsung Xpress Color C410W. It is not printing any pages. When I place print comment it gives me blank page. And sometime restart by it self. while printing. I need your advice what can me the issue.
@ataulghalib86
4 жыл бұрын
Just fixed clx3305. Great video thanks
@thomasgovender5874
4 жыл бұрын
hi how did you fix it? Did you replace the rubber part of the solenoid?
@GrahamHaughton
9 ай бұрын
I followed your video as had the same problem with a C410W. Now when I power on the rollers don't move on start up and I get a red error light. Any ideas what I've done incorrectly. Any help gratefully received. Graham
@PaulMott1
8 ай бұрын
Awesome video thanks for saving my printer from the land fill. I would just add that I don't think you need a new part. It's just a coil of wire that generates a magnetic field -- not much can go wrong unless it gets shorted -- and mine was not. The problem is that the little spring loaded metal teeter rests on a small rubber pad. Over time the spring pressure will cause the rubber pad to permanently collapse, and then the metal teeter is too far away from the solenoid and the magnetic field cannot overcome the spring. So I just peeled off the old rubber pad and put a dab of hot glue there - it holds the teeter up higher now and problem solved!
@kristiansolstad9068
6 ай бұрын
Wonder if this is my issue , samsung clp-320 , dont see anything happen in paper tray, even loaded full says paper is empty in tray1, power up it start fan, look for toners, smart panel show toner levels , after clean waste tank I get only the paper error, I get very short flash green and then stay solid red and toner lights are dark. just got this second hand shipped, first I see is its pouring black toner out without stop pounds of it. Guess its bad idea ship a printer with toners installed. After tons cleaning i get the mentioned error. Havent opened all of it yet, its likely full of toner on every part inside
@RoelandMerks
3 жыл бұрын
Thank you so much for the very clear explanation. It work like a charm for my Samsung XPress C460W on second try!
@patrykf4993
2 жыл бұрын
What solenoid symbol for c460w printer?
@cashewABCD
Жыл бұрын
Thanks for the tips. Fixed
@ataulghalib86
4 жыл бұрын
I have a question. I am after doing the solenoid fix printing works perfectly but if I try to copy I still get the paper jam error. Could you guess what would be problem. I have CLX-3305
@PaoloMarcelli
4 жыл бұрын
Hi! Honestly I don't have any idea, aside of any paper format settings being wrong in the copy.
@tavoguzman2322
3 жыл бұрын
HELP mi samsung clp365w has the 3 leds blinking everytime i turn it ON, it dont do anything else, ay noise, nothing just the leds on green and blue
@Joost001
3 жыл бұрын
Thanks a lot! Followed your instructions and my printer works like a charm again! :)
@Kearwood
3 жыл бұрын
Thanks for the great tutorial, fixed my CLP-360!
@jwilkinson341
2 жыл бұрын
I cant get the spring gear off there are 2 little clips that you push to a side 11.34 in the video my printer 460W gear will not come off no matter witch way I lever
@janverdam5764
2 жыл бұрын
Thank you so much for your video. It helped me to diagnose the problem and with your clear explanation I also could repair the printer. Perfect job!
@Cartoonicus
2 жыл бұрын
Are normal people like us, seriously supposed to be able to do all this?
@Kornel1100
3 жыл бұрын
It worked for me as well. Thanks for making as little steps as needed. This took me about 1,5 hours, so not much at all.
@PaoloMarcelli
3 жыл бұрын
Great job! :)
@pinoywalkerpro2225
2 жыл бұрын
The issue with mine is that when I turn the printer on, the wps light comes "on" for half a second then it disappears.. then the power on button lights green. Nothing happens after that no matter what button I pressed or long pressed or combine power button with other buttons with long press.
@djumd
4 жыл бұрын
Thank you very much
@chris746568462
2 жыл бұрын
The solenoid coil is 24v 120 Ohm. Glued a m3 washer under the foam stopper and it works again.
@simonlam8834
3 жыл бұрын
保罗,感谢您的精彩教程!你令到我的 C460FW 只花了10欧罗便活过來了!
@zedzed1046
Жыл бұрын
My CLP 680 ND randomly picks up but then sends the paper under the tray, cant figure it out.
@davidrlin
3 жыл бұрын
Thank you for your video. Mine really can’t hear any notice, like main motor not working or not heat up?
@joseantoniomartinez5423
2 жыл бұрын
Paolo thanks God for your clear explanation. I solved the damage without any setback. Regards
@davidbevan2439
4 жыл бұрын
Thanks very Much for this. you have just sorted my printer for me. i dismantled cleaned and resistance checked solenoid. mine was stuck. I guessed at that point nothing to lose if i reassemble hey presto works.... Thanks...
@juhakera4646
Жыл бұрын
Thank you very much, indeed. My Samsung C460W run into this paper jam problem and I managed to heal the it following your very good instructions: Actually I replaced the whole unit JC93-00547A but I ordered a solenoid, too and shall prepare a spare part from my old JC93-00547A for my neighbour who owns a similar printer.
@TheMrmonteiro
2 жыл бұрын
Ciao Paolo! Do you have experience with Samsung CLP610ND? I have a Samsung CLP610ND and I can't eliminate the message "door open/check belt tranfer". The door sensor of PCB board is OK, but I could not find the error reason. Did you heard some trouble like this? Thank you!
@PaoloMarcelli
2 жыл бұрын
Hi Alex! I don't have any experience with the CLP-610ND, as it's not a very common model here, all I can think of at the moment is to check the installation of the transfer belt... If you haven't done it yet have a look at the service manual, search for PTB (Paper Transfer Belt) and you'll find heaps of informations on all the parts of it and how to install it and what to check. I cannot redistribute service manuals but you can find it easily on google.
@robparkinson9850
2 жыл бұрын
the hardest part by a country mile is getting solonoide back in, whether u repair original or use a new part. there is not enough detail in how to get it back in
@reimohaidak8811
4 жыл бұрын
Thanks
@matthiasseidel6084
Жыл бұрын
thank you. We managed to repair our printer this way. Very Happy:). JOHANN
10 ай бұрын
Wonderful! Thankyou! Worked perfectly for me and my C460w. Like others, I fixed the solenoid instead of replacing it. the Rubber pad had drifted a bit and was no longer touching the "counter flange" that the rubber pad should bounce agains. I moved the rubber pad back tow where it was supposed to sit and also bent the counter flange a bit downwards to make the arm not swing as var from the solenoid. Everything seems to have worked.
@DrThalamic
Жыл бұрын
Thanks for the info --- I purchased a Samsung C460W for $20 that wasn't working due to a paper pickup issue. The steps for this unit were very close to your demonstration, however when it came time to pull the 4 sets of wires through the hole this unit had a small hole and I didn't bother passing the wires through. I proceeded to cover the foam on the solenoid (still attached to the unit) with Kapton tape and reassembled the unit. The solenoid was fine, it was just the foam that broke down and became adherent so by covering the foam with Kapton tape the problem was resolved.
@ataulghalib86
4 жыл бұрын
very very very useful. Thanks
@marcogallino351
3 ай бұрын
Ciao! questo video è sempre un riferimento... dopo 3 anni però si presenta un problema diverso: prende il foglio e lo trascina per circa 20-30 cm., inizia la stampa e si inceppa... Mi sembra di capire che non si stia parlando del solenoide incriminato ma di un problema diverso... vado di assistenza o rottamo il fido muletto?
@alessandrobrazil3886
Жыл бұрын
Hi Paolo, I need the FIRMWARE CLP-365W , Do you have this???
@robertconnier9457
Жыл бұрын
Fixed my CLX-3305FW using this instructional video. In my case, the solenoid had died (open circuit), as the pad on the original solenoid was not sticking at all. If you wear magnifying glasses, it helps a lot to see the small parts clearly.
@laurensijsselmuiden6696
Жыл бұрын
Amazing video! Thanks for showing how to repair my Samsung CLP-365w. I ordered the Solenoid and am curious if that will solve my paper error. Thanks again for this tip!
@jerryk7745
8 ай бұрын
Great video, thanks Paulo. I was ready to go ahead with your fix, but could not see clearly if the roller was turning. So I took out the paper tray and then propped up the front of the printer about 8cm. Then the roller is not only visible but also accessible to clean. There is a little plastic tag to the right of the roller which detects the paper tray. if you press the tag and use a torch you can see the roller turning to try to feed when you press copy. Also a good time to clean the roller with a cloth soaked in iso-propyl alcohol. Be careful roller does not grab the cloth if you try this! Two other points your viewers might like to check: Place the tray and paper in a warm dry place for 24 hours. It's surprising how much humidity paper can absorb - this affects paper pick-up. Final point: make sure all the paper guides in the tray are snug against the paper - especially the one at the back of the tray (farthest from the roller). Doing all this got my printer working again without replacing the solenoid! Thanks again
@ilmioutente
4 жыл бұрын
Grazie, ottimo video. Con pochi euro ho evitato di buttare una stampante per il resto buona.
@Hakie62
2 жыл бұрын
Thanks a lot. I have bought a replacement printer. But I will try to fix my “broken one.). I am pretty sure your tips will fix it. 👍. Subscribed!
@vadimbyallcare6352
2 жыл бұрын
Thank you deep !!! In my case the Model is Xpress C480FW. But everything inside is almost the same. The printer do not want to pick up the paper. This tutorial helped me a lot to proceed with the deep cleaning.
@melissacorcoran1466
2 жыл бұрын
Can you help. I have a Samsung c410w and it just started printing and stopping half way. And the paper comes out with a curl in the middle of the first page. When it goes to print the 2nd page it gets stuck halfway and I need to clear the jam and restart. Please help. This is my favorite printer and I have already replaced 1 part.
@PaoloMarcelli
2 жыл бұрын
Hi! So it comes out with a curl in the middle... Check the fuser unit, see if the fuser rollers are both in good shape. You can access them by the upper cover, right where the paper comes out
@anthonys555
Жыл бұрын
Thanks this worked for me. Instead of removing the rubber I put nail varnish on which still didn't work. What worked for me was super gluing a couple of layers of card on top of the nail varnish so that the gap between the solenoid and lever was a bit closer. 2 layers did it for me. 3 layers was too much and the plastic gear was not being held. Works perfect now.
@patrykf4993
2 жыл бұрын
What solenoid symbol for c460w printer? JC33-00025B?
@hannavandenbulcke2801
3 жыл бұрын
Hello Paolo! I have a Samsung Xpress C1810w having a similar pick-up paper issue. Would the inside of the c1810w printer be similar to the printer in this video? Meaning I could follow your instructions above and apply to my printer? Also, if so, could I purchase the same solenoid mechanism from the link, or does it need to be a different one? Thank you in advance for your time!
@georigoST
3 ай бұрын
I looking for dump flash and eeprom from this board CLP-365W (V3.00.01.14) Where can it be found, downloaded?
@PaoloMarcelli
3 ай бұрын
Hi, I found this site that has the original firmware on the bottom of the page, where it says "Оригинальная прошивка". printservis.com.ua/index.php/blog/item/378-proshivka-fix-samsung-clp-365w-versiya-v3-00-01-11 It even has instructions on how to get the printer to forced firmware update, I used a translator obviously XD
@j.o.a.t9718
Жыл бұрын
I am getting the paper jamb error but it will print test page. I am assuming then that the problem is not this sensor?
@millervillamarbravo
4 жыл бұрын
Hi, i have the same printer, same model. But my problem is that my printer doesn’t turn on. I have checked the power Supply and i saw That was Only 22vcc and 5 vcc and no more. The power on button is working ok . Anyone knows how to Fix it ? Tks
@pseast
2 жыл бұрын
worked to fix xpress c460w. Though, I didn't replace the solenoid and just replaced the foam pad as suggested in another video that points here. Thanks!
@sorinpopescu3576
10 ай бұрын
Thanks for the video. Managed to fix my printer following this.
@paddy1068
10 ай бұрын
Paolo, thank you so much for this detailed video!!!! 🙏It only took me about one hour to repair the printer. I was not sure this was the reason, but obviosly it was. The printer is up and running again. 😊
@pamelapere
3 жыл бұрын
I fixed my printer (with just 9€) !! Thank you so much 😀
@stefroelandt18
3 жыл бұрын
Did not work for me. Replaced the solenoid but the paper pick-up shaft is still not spinning. Even opened it a second time to adjust the spring loaded gear and afterwards a paper entered the printer halfway but afterwards no more movement.
@stacksweaver
2 ай бұрын
Followed the steps and my printer is printing again!!!! Thank you!!!!
@ykejaarsma9876
5 ай бұрын
Thank you. Now my printer works fine again. Yke Jaarsma Netherlands.
Пікірлер: 328