thaks, your video actually stopped me to disassemble whole robot. I have tried to pour citric acid with water to the hole under tank first and it worked.
@kristiankundrat283
6 ай бұрын
Thank you very much for the video!!! I disassembled the robot like you did and clean the water pipes with sirynge ( i dont have small compressor) and actually it worked! I cleaned all the pipes from the start to bottom like you in the video. Thanks for the video and help!!!
@SAMUELDIY
6 ай бұрын
Glad to help, Thank you for sharing
@steadirob
Жыл бұрын
Looking at your video I was encouraged to open the robot and that went well. I noticed a small cylinder in the tubes towards the 3 water drippers just after the small pump mounted on the right (seen from the bottom. This is a one-way valve and in my case it was most likely stuck because of dried up water residue (calcium). After gently poking the inner rubber membrane loose with a thin metal rod (toothpick might do too, just don't puncture it) the water, pushed by a syringe was able to squirt through the drippers! ALL GOOD NOW!
@steadirob
Жыл бұрын
Additional info: it is important to prime the tube from the water reservoir to the motor! My first try I forgot that and got "insufficient water" message, because the pump is pulling air. Opened it up again, took the tube from the anti leak valve and disconnected the connector from the pump motor on the board. I placed the FULL water compartment on it's receiving nipple . Than a 5volt power supply on the motor will pull - slowly - the air out and it will suddenly start to squirt water! Connect to the valve again and check once more with the 5volt power supply if it comes out of the drippers! Reconnect the pump connector to the board and close the machine.
@SAMUELDIY
Жыл бұрын
Thank you for sharing this importent detailed information
@patriciomaldonado5921
8 ай бұрын
@@steadirob Thank you! It's what I had to do. I disassembled the robot and the valve was stuck. And ready!!!!
@hrvojekrsnik6572
7 ай бұрын
Try this first as it's quick and easy, and solved my problem for a while - in my case there was limescale buildup on 3 outlets that you see when you remove the mop holder. I just cleaned them by sticking interdental brush in them for a couple of times and water started flowing again.
@hrvojekrsnik6572
4 ай бұрын
Update: after a couple of more cleaning sessions mop cleaning completely died, tried cleaning the nozzles and everything as shown in this video. I ordered new water pump assembly including nozzles from Aliexpress for around 25 eur and replaced it pretty easily (you just need to unscrew two additional screws to remove the plastic funnel that's above the nozzles). It works great now, so I guess the water pump died (which you can get for 12 eur).
@salomonserfaty
2 жыл бұрын
Thanks. I did it with a syringe with air and then eith water and it worked like a charm. Something was stucked, probably lime, in the tubes.
@Nicolas-of6li
2 жыл бұрын
Thank you! i wouldn't have managed to pick it appart without your instruction. The front shield was a mess to align. I manage to get the pump working by pressuring some water through the main water intake with a pipe and a syringe, so it wasn't necessary for me to disassemble it completely in the end, heh. This seems to be a common issue with robot cleaner
@SAMUELDIY
2 жыл бұрын
using a syringe is a good idea, thanks for your input 👍👍
@FactsChannelno1
Жыл бұрын
Can u help me bro i have same problem @
@LeVarker1
Жыл бұрын
Would you mind telling us which pipe did you use?
@FactsChannelno1
Жыл бұрын
@@LeVarker1 bro do u hv same water issue. If u fix it can u upload a video for me so i can fix
@Nicolas-of6li
Жыл бұрын
@@LeVarker1 more exactly it was some kind of silicone tube that fited both on the syringe and robot's other tube (i don't remember how it was exactly). the idea is just to get an air-tight passage to expulse whatever is blocking the water flow. it can be either a syringe or a bike pump, anything with what you can apply enough pressure
@verzatileable
Жыл бұрын
I follow this video and it works! The important part is to clear the air and water tube with syringe.
@SAMUELDIY
Жыл бұрын
Very Glad To Hear This
@geminidion1099
Жыл бұрын
Thanks for your kind information. My Mi robotic water blocked is really solved by following your guideline.
@ncastrobize
Жыл бұрын
Thank you very much! I followed more or less your procedure and fixed my cleaner's water problem!!
@nerminator6266
2 жыл бұрын
Perfect guide, I felt it is the right source when orange light is dissappeared :-)
@SAMUELDIY
2 жыл бұрын
I am Glad If It Helped Repair your own
@shmuelos
2 ай бұрын
thanks, few months after shooting this video it hapoened to me to, this time I did not disassembled it because I was sure it is something with the tubes again, I just flipped it over and again with high pressure of air to this bottom holes I cleared the clog drain holes much fasyer then disassemble😊
@MuratDeryaBulut
7 ай бұрын
İ cleaned, (pushed and pulled printer nozzle with cleaning gasket and syringe.) Solved in 15 seconds. try it's easier and not risky
@XavierGarciaHerrera
Жыл бұрын
Just tried it and worked perfectly!
@RomaDruzhkov
2 ай бұрын
Thanks for the video! Mine didn't work because the nozzles on the bottom side got clogged due to hard water. This could be fixed without disassembly. I had to just puncture them with the needle.
@LuisReyes-cf9di
Жыл бұрын
Thanks, I just did the same thing but nothing, then I realized that the water pump makes it sound like it's working, but it's not actually pumping water. I opened this pump and found the internal membranes broken, so I will order a new one.
@SAMUELDIY
Жыл бұрын
Let us know how it went, after you replace the membrane
@waldevv
Жыл бұрын
Need to give this a shot, took the entire thing apart once already but ultimately just put it back together after fiddling with the pump, didn't think about using compressed air
@SAMUELDIY
Жыл бұрын
Let us know what was the outcome if you will try
@aldrinrivero
11 ай бұрын
Just did it, and it works!!! Thanks a lot 🙏🏾
@SAMUELDIY
11 ай бұрын
yesss,I am glad to help
@HernanCrespo06
10 ай бұрын
I had a problem with the one way valve. I unclogged it by pushing water with a syringe and I left it underwater overnight. The next day it was working correctly. The one way valve is activated by pressure, you need something to push the water through.
@SAMUELDIY
10 ай бұрын
that is good to know, cheers,👍
@franckkarsentyguitare8157
Жыл бұрын
Super t’as vidéo ma beaucoup aidé
@ernestomartinez4571
Жыл бұрын
amazing video! can you show all the tools that you use? I want to buy the battery stuff and the vacuum
@SAMUELDIY
Жыл бұрын
Thank You, The battery stuff I made myself from broken children's toy parts and some electric alligators: I searched for you and those components are possible to buy: here are some links: Alligators www.aliexpress.com/item/4000791558387.html?spm=a2g0o.productlist.main.31.78ae67aa5pnyZW&algo_pvid=a5e36e3f-7c97-4da6-9846-b078e79e4219&algo_exp_id=a5e36e3f-7c97-4da6-9846-b078e79e4219-10&pdp_npi=3%40dis%21USD%211.12%210.95%21%21%211.12%21%21%402100b78b16900482198542700d0748%2110000007871081533%21sea%21IL%21925552221&curPageLogUid=IS2GpANKODsp battery case: www.aliexpress.com/item/1005004825062091.html?spm=a2g0o.productlist.main.4.584325eclN1LG2&algo_pvid=4846a965-ad7f-47bb-a1c2-b69b997e5fd4&algo_exp_id=4846a965-ad7f-47bb-a1c2-b69b997e5fd4-1&pdp_npi=3%40dis%21USD%212.80%211.68%21%21%212.80%21%21%402145280e16900477849598826d0762%2112000030626614522%21sea%21IL%21925552221&curPageLogUid=QIsBLzGVlVbF I blow the compressed air with my compressor but many viewers manage to do this with a syringe: syringe: www.aliexpress.com/item/1005003834170404.html?spm=a2g0o.productlist.main.13.32f34d00ZuuusX&algo_pvid=1db1438c-8857-4b04-8375-a78f4f3cc4fa&aem_p4p_detail=20230722105420162699733929800003713587&algo_exp_id=1db1438c-8857-4b04-8375-a78f4f3cc4fa-4&pdp_npi=3%40dis%21USD%214.90%212.3%21%21%2134.97%21%21%402100bfe316900484599646921d07ab%2112000027301192271%21sea%21IL%21925552221&curPageLogUid=RsbHhAJTgK0n&search_p4p_id=20230722105420162699733929800003713587_1 compressed air: www.amazon.com/-/he/Falcon-Dust-Off-Electronics-283-5-%D7%97%D7%91%D7%99%D7%9C%D7%94/dp/B01DPW2SR2/ref=sr_1_44?crid=2CZ5B7JLM2X83&keywords=compressed+air+can&qid=1690048637&sprefix=compressed+air+can%2Caps%2C266&sr=8-44 or my compressor www.aliexpress.com/item/1005005257056039.html?spm=a2g0o.productlist.main.127.2524361dxsBUDw&algo_pvid=9328f3f9-7d8a-40d7-8efd-647f64029ca4&algo_exp_id=9328f3f9-7d8a-40d7-8efd-647f64029ca4-42&pdp_npi=3%40dis%21USD%21157.00%2178.5%21%21%21157.00%21%21%402145265416900487088024854d0796%2112000032383205068%21sea%21IL%21925552221&curPageLogUid=DGGJMxhqISYa Good Luck
@haajee1
Жыл бұрын
I blow some air in the hole on the downside of the robot vacuum with should be the intake air hole. And the orange light is not blinking anymore and looks it sprays water again. Think there was some dust inside.
@SAMUELDIY
Жыл бұрын
Since you say this worked for you ,I will recommend everyone with this issue try blow some air to the intake hole near the left spinning brush ,before disassemble
@haajee1
5 ай бұрын
@@SAMUELDIY Sadly after a long time of use it stoped working again. I think the oneway valve is broken or something. Did you also the tube? It's 4mm but is it latex or silicone tube?
@SAMUELDIY
5 ай бұрын
@@haajee1 Hello,I must say this happened to me as well after a year that it was working just fine I got the orange light again and no water, this time I did something else; I just removed the water tank, and the mop and then I flipped the robot on the table, On the bottom there are 3 very little holes and I pushed compressed air to every one of these holes till I felt the air is coming out from the other two holes this removed whatever was stuck in the tubes and the robot was working again with the mop. I am not sure what are the tubes are made of silicon or latex and honestly I don't think it matters as long as it is in the right size and can carry water. GOOD LUCK!
@ChiragDedhia
2 жыл бұрын
Thanks for the video. I think I have an issue either with water pump or the filter downstream of the pump. How did you check the pump functioning? You did connect some cables to hear voice. Can you elaborate voltage used? Also, I can't blow air from the filter unless I use some pressure pump.
@SAMUELDIY
2 жыл бұрын
thank you! To check the DC motor on the pump I connected two AA Batteries in line so 1.5X2 =3 Volts and I used electrical Alligators clip to connect some copper wires to it, and what I wanted is to hear the motor spinning. I am not sure I understood what you said about blowing air to the filter, I used a compressor to blow air into the tube after I disconnected the tube line and if you don't have a compressor maybe you can get compressed air in a can like is used to clean computer hardware.
@asimali9766
2 жыл бұрын
Motor is 3.3V.
@EmmanuelSkarpeta3092
Жыл бұрын
Hello Sir :) Do you maybe have any idea what can be the reason of brush working non stop ? Even if mop is reseted, discharged or turned off it is not helping. Everything seems to work perfectly fine except brush which is still spinning even if vacuum is off :/
@SAMUELDIY
Жыл бұрын
This sounds like maybe water got inside your device and shortcut something on the electric board and in this case, it might be difficult to fix. also, this can be a software issue, and you might be able to fix it by performing a firmware update from the app.
@helenakri7282
Жыл бұрын
Thanks a bunch for the video)
@SAMUELDIY
Жыл бұрын
Glad to Help
@khairialias4629
Жыл бұрын
Spent 1 hour dissamble and cleaning the tube but problem still persist. At first, water still coming out during mopping. Now nothing comes out. But theres weird sound when on mop mode. I bet the water pump faulty. Not sure if theres replacement for that motor…
@SAMUELDIY
Жыл бұрын
sorry to hear that, did you try to listen to the motor while the vacume was disassembled like I showed in the video?
@SAMUELDIY
Жыл бұрын
also check out this link to the pump on ali express: Just found this amazing item on AliExpress. Check it out! ₪ 12.34 65%OFF | Water Pump Motor for Xiaomi Mijia G1 MJSTG1 Robot Vacuum Cleaner replace Parts a.aliexpress.com/_Evmj8Mv
@khairialias4629
Жыл бұрын
@@SAMUELDIY unfortunately didnt hv the tools to test the motor. Thanks for the recommendation though. Will buy new motor and give it a try. Cheers!
@GabrielBiff
7 ай бұрын
My S10+ stopped pumping water. I’m pretty sure it’s something the the pumper, but I couldn’t get access to it… I searched the whole KZitem, even did Chinese search, but there is not even a single video of someone disassembling this thing. I regret so deeply for not getting a more popular model… now I’m stuck with something that only vacuums…
@SAMUELDIY
7 ай бұрын
Sorry to hear about that, you can try this: in the xiaomi there are 3 very little holes that the water comes out from, try to turn around your vacuum and search for similar holes then you will need something strong to blow air inside these holes, a compressor with small enough tip.
@mrtechnyix
6 ай бұрын
this not resolve Mop has not ben installed.. Update: need order map and watertank combinated sensors.. in aliexpress aprox 5-12$
@SAMUELDIY
6 ай бұрын
thanks, the mop has not been installed is a different problem Try to verify all the contacts are positioned correctly and that there are no abstracts between the vacuum and the mop assembly
@qqqq1888
2 жыл бұрын
i facing the same problem with my xiaomi c1 vacuum . my unit just used fr abt 5 months plus, (bought in June ) problems occurred in early Dec . after took quite a long repair time, the seller at last exchanged a new unit for me (i have to bear all the in out shipping cost). unfortunately, the exchanged unit, also only last for 3 mths, it have mopping issue again. but seller say only 6 mths warranty. no entertain me after that. very lousy product and service . problem : it not mopping, water keep dipping, and also the mapping is so random ..... very disappointed
@Tammy10018
2 жыл бұрын
Funny how it stops working properly after the warrantee falls away😡
@HonzaZalabak
Жыл бұрын
Dont you know if you are able to blow thru the water filter? In my case i bought this from some woman and I think she may have used some kind of cleaner and the filter is clogged. I cant blow thrue it
@gabrielaguiar4708
Жыл бұрын
Did you find a solution? Same problem here. I can blow thru all hoses, except the filter.
@HonzaZalabak
11 ай бұрын
@@gabrielaguiar4708 sorry i did not see comment. I ordered new pump set and what I think it is not filter, but one way valve. And I also coild not blow thru the new one. I installed the set and it works fine now
@gabrielaguiar4708
11 ай бұрын
@@HonzaZalabak Oh I see. No problem, I ordered a new pump set and its working now too. But thank you!
@HernanCrespo06
10 ай бұрын
@@HonzaZalabak @gabrielaguiar4708 The one way valve is activated by pressure, you need something to push the water through. I used a syringe.
@carloscarvajal7651
2 жыл бұрын
Hey sir where do i can find the motor of this vacuum?
@SAMUELDIY
2 жыл бұрын
when it was open I was able to identify 3 motors, one big motor for the vacuum turbine, one medium-size motor for the wheels, and the small motor that is in this video for the water pump, hope that helps
@jasper417
2 жыл бұрын
For me the problem was a clogged pump and 1-way-valve.... I bought mine used, and the previous owner apparently used some kind of detergent in the water, which apparently you shouldn't
@HernanCrespo06
10 ай бұрын
I dont know about the clogged pump, but I unclogged the valve by pushing water with a syringe and leaving it sumerged in water overnight.
@sarahsiregar
9 ай бұрын
@@HernanCrespo06hi, did you take apart the robot like in this video? Or did you push the water from the valve near the water compartment? Thank u
@HernanCrespo06
9 ай бұрын
@@sarahsiregar I took it apart and checked every single part by itself, that's how found out that the problem was the one way valve (the thing the person in the video thinks it might be a filter). I've seen videos where people push water directly from that valve near the water compartment and it worked for them.
@marygoh7004
6 ай бұрын
@@HernanCrespo06what do you mean push water from the valve with syringe? I want to try this as I've taken the whole thing apart but I'm pretty sure it's the valve that is the problem
@HernanCrespo06
6 ай бұрын
@@marygoh7004 I don't know if i can post links so i'll leave the title of a video where they do that: Мелкий ремонт робота-пылесоса Xiaomi Mijia Mop Essential (G1) когда он не подает воду на тряпку. If you've already disassembled it then you can do what @SAMUELDIY does in this video at 11:00 but with water and a syringe instead of air.
@HdzJaziel
2 жыл бұрын
Hello sir, I have the same issue, I have done exactly the same procedure you did, unfortunately I couldn't solve the problem. Do you have another tip?
@SAMUELDIY
2 жыл бұрын
Take out the water tank and check if something blocking the water exit on it. also, you can try to fill it with vinegar it might dissolve fur if it accumulates inside your tubes
@Jardzi18
Жыл бұрын
I have different problem when i give mop its hont say mop instaled and nothing is showed in app...and then sometimes says mop instaled and works for couple seconds 😤
@kadriyetopcu2983
Жыл бұрын
Aynen videodaki bendeki ürün fakat dün itibariyle silme yapamıyorum mop ıslanmiyoryardım lütfen
@davidaguas5540
Жыл бұрын
After I did this I get a message saying "low water level" and the vacumm stops working. I cant find a water level sensor anywhere, do you have any idea of what could be the issue? Thanks!
@SAMUELDIY
Жыл бұрын
From what I know, there is no water level sensor component, when the robot has a problem pumping or sucking water from the tank because of any reason (clogging or pump issue) It will state "LOW WATER LEVEL"
@MikariN40
2 жыл бұрын
Hello My robot doesnt doesnt use water at all. I test with 4 AAA battery and cant hear some voice. When I put the water bin, robot detect the water bin. What could be issue?
@shmuelos
2 жыл бұрын
you said it man, if you can not hear your motor working it will not pump the water even if it detect the water bin, Replace the motor!✌✌
@MikariN40
2 жыл бұрын
@@shmuelos you mean motor in water bin or inside the vacuum?
@shmuelos
2 жыл бұрын
@@MikariN40 There is no motor in the water bin,there are couple of motors inside the vacume.one of the motors is the motor for the water pump(this is the motor that in the video he connects the external AA battery) if this motor is not working the vacume can not suck water from the bin to the vacume.
@mervearslan2050
2 жыл бұрын
Umut bey merhabalar ben de bir çare bulamadım daha önce birkaç defa çözmeye çalıştım sorunu içini açtım komple vs boruları temizledim olmadı. Sonra bu videoya denk geldim ve tekrar denedşm yine sonuç alamadım. Bendeki sorun haznede su olmadığını söylüyor cihaz. Sİzdeki sorun tam olarak nedir ve çözebildiniz mi?
@MikariN40
2 жыл бұрын
@@mervearslan2050 ben de su var herhangi bir uyarı vermiyor sadece suyu kullanmıyor. Açmadım daha içini. Sağını solunu açarken kırarım diye tereddüt ediyorum
@alexprimero5
2 жыл бұрын
Hello sir. my vacuum seems to keep throwing water when cleaning is finished. I have found several times around the charging port a large puddle. any idea what it can be?
@SAMUELDIY
2 жыл бұрын
It Sounds like a leak in the device,maybe you should check this page :smartme.pl/en/how-to-fix-a-problem-with-leaking-water-in-xiaomi-and-viomi-vacuum-cleaners/
@deaklajos8760
2 жыл бұрын
@@SAMUELDIY The link above is not relevant to the Mop Essential. Different design. Mine is leaking from the 3 ports and drains the water container while charging. I guess for some reason the way of the water is not restricted (by the pump?) and siphon drains the remaining water.
@ivonanedyalkova2274
Жыл бұрын
@alexprimero5 did you fix the problem ? Mine is also leaking like yours and can't find how to fix it.
@public_static
2 жыл бұрын
היי, יש לי את אותה תקלה ואין לי רצון/יכולת לפרק את המכשיר.. אפשר ליצור איתך קשר?
@SAMUELDIY
2 жыл бұрын
המייל שלי מופיע בעמוד של ה-ABOUT, כעקרון הסרטון מיועד למי שיכול ורוצה לפרק את המכשיר
@adrianalexisgonzalezailant4496
11 ай бұрын
Bueno e mi caso me toco desarmar la bombita de agua los cauchos se invirtieron.
@SAMUELDIY
11 ай бұрын
translation; 'Well in my case I had to disassemble the water pump the rubbers were reversed.?'
@pe_rodriguezh
7 ай бұрын
Como sucedió eso amigo?
@adrianalexisgonzalezailant4496
7 ай бұрын
@@pe_rodriguezh no se uso por buen rato y se presento el daño
Пікірлер: 107