Thank you so much. It actually works. It may take a few times to repeat the process as the wood can return back to its original state but after some tries my boards are now flat. Thanks
@komitekomite
4 жыл бұрын
It really works. My cupped boards are perfectly flat now. Thank you.
@Roadwarrior721
Жыл бұрын
Just found this, is there a follow up video to see the results?
Thank you sir! I just made a chess board and had cupping a day after building it and this worked like a charm after a couple times. Saved my father in laws Birthday present! Much appreciation
@prestonlandolt
2 жыл бұрын
Literally same exact problem. With a chess board!!
@wanderscuisine1283
Жыл бұрын
Bro same
@kulotski648
4 жыл бұрын
oh were is the continuation? can't find it :( i liked how it all began, but now i'm hanging
Im looking for the second video and I don’t think there is one. ☹️ I’m trying to repair an old table. The wood is warped on several boards. I hope this works. I will let you know.
@finewoodworkersstudio5215
3 жыл бұрын
Video 2 will be posted Jan 4! Once the boards appear flat, continue flipping from top to bottom on the plastic until they appear dry and stable. Then set them on sticks so they dry on both sides . continue to watch them. If on developes a cup turn the cup side down and continue drying and watching
@jessejameson154
3 жыл бұрын
@@finewoodworkersstudio5215 does it need to be warm in the workshop , e.g., summertime? Or will it work regardless of temperature?
@brucemiller1696
9 ай бұрын
@@finewoodworkersstudio5215there would not be a warped problem if the person that left the panels on a bench overnight would have stood them up so that plenty of air got to both sides.
I tried this wetting one side on a 4x8 sheet of plywood and it did not work for me
7 ай бұрын
Could be that the moisture can't pass through plywood as there is glue between layers.
@DK-bl6nu
3 жыл бұрын
Hi Dale- I was curious to know if you also have experience in wood finishing, as well. If so, do you know how they used to do the limed oak (blonde) finish on furniture, such as white oak or ash, back in the 50s? I can't find anyone who does. Thanks. DK
@teckyewng
Жыл бұрын
My cabinet door have been stain with some coating. Should I remove the coating before apply the water?
I was asked if water will flatten a twisted skateboard deck? I don't know. is it plywood?
@davom4036
Жыл бұрын
What happened to the second part?? Did it work? Did anyone have any luck?
@finewoodworkersstudio5215
Жыл бұрын
Yes it works! It may take a few repeats as wood like to return to its original shape
@willdatsun
Жыл бұрын
horizontal vid next time please
@finewoodworkersstudio5215
Жыл бұрын
That's a good point...so the bow is more visible
@DoraDominguezCarey
4 жыл бұрын
Me, too. I was just looking at it bc one of my shaker cabinet doors that I recently made has warped. Where's the rest of the vid? We're left hanging, pardon the pun.
@finewoodworkersstudio5215
4 жыл бұрын
Dale here. check the panel as it dries, when you see it begin to warp in reverse, flip it over. When you see the panel "cupping" on top , flip it back again. Continue flipping the cupped side down till panel is flat. Don't add any more water unless this drying process fails the first time.
@finewoodworkersstudio5215
4 жыл бұрын
Set the flat panel on 2 sticks to completely dry a few days, depending on weather
Пікірлер: 45