How to make a protrusion stop: kzitem.info/news/bejne/qmpnnYqMqJlhdZg
@balex7476
6 жыл бұрын
Matt Estlea what kind of bench is that. Do you have plans for it?
@TheCAPTAINman128
5 жыл бұрын
Do you need a very specific and expensive tool for that too?
@douglatins
4 жыл бұрын
Did you release the video to get rid of the rust?
@jeffp53090
2 жыл бұрын
That’s the most straightforward explanation for creating a camber I’ve ever seen. We’ll done.
@luckyhiker3434
5 жыл бұрын
Hi Matt, you are a captivating speaker. We can not even blink because there is no fluff and only what is important is said.
@AndreaArzensek
7 жыл бұрын
Even though I know a lot of these things I still learn more and I refresh my knowledge. Great tips on sharpening! Thanks Matt.
@gavisaethelion
Жыл бұрын
Hi Matt, thanks for this video. I spent a good few hours sharpening my grandad's plane blade; looks really good for my first attempt!
@daleromney6062
5 жыл бұрын
This is the best video I have seen on sharpening, and I have looked at quite a few.
@Swarm509
5 жыл бұрын
Great video! I love seeing different ways people sharpen and the systems they have. I picked up a few tricks from this I will try next time I sharpen my planes, such as ensuring I count out my strokes and shifting the pressure around the plane edge to get a repeatable curve. Super new to this so lots of room to get a system that works for me. Honestly I have been using Paul Sellers method of since that worked best for me with the materials on on hand. I will say to anyone who complains about the tools used... you can do all of this with sandpaper (from re-angling the iron to final super sharp edge) but it will simply take you longer to do it, but if that is what you have use it. As you get better, or are willing to spend more money, you can buy stones and diamond plates and just save yourself more time and improve your edges.
@jamesperrin3762
6 жыл бұрын
Thanks to this video and a couple of others I've managed to straighten the curved factory edge on my cheap as chips Record No 4 and got it stupidly sharp. Done with a Faithful 400/1000 diamond sharpner, 10 quid honing guide and homemade strop. Made a protrusion guide block so I can do it again consistently, which is what will save you time and steel rather than being dead on the angles. Never going to do any fine furniture making but enjoy your videos a lot. The transparency and honest style is great. OK where are my Stanley chisels!
@oldms
4 жыл бұрын
You have a real gift for teaching. I watched several videos before this one and you explained it far better than anyone else. Something about how you teach resonates with how I learn I suppose. I should have come to you first because this isn't the first time I've ended up finding you to be the one who explains something perfectly. I've learned my lesson this time. I'll subscribe to you and get lesson I was looking for straight away.
@Mpafanai46
3 жыл бұрын
Always watching from far far noth eastern states of India, i got confident on sharpening plane, good luck, thanks alot
@neilvirgo426
6 жыл бұрын
I can't believe people gave this the thumbs down - his videos are f**kin ace.
@LumenP1023
6 жыл бұрын
the problem is, in the long term, you'll have to reflatten the cutting edge, and the more you use the plane, the less flat your work pieces will turn out. This is over the course of several years of working and recambering/sharpening with the blade though, so for many, its negligible. Me, I just round out the very corners, to stop leaving tracks. So my preference is the opposite of Matt's. It preserves the straightness and flatness of the blade, and gives a much more accurate flat result on your work.
@richardsinger01
5 жыл бұрын
Lumenpraebeo I find that’s ok for smoothing planes, but I prefer a camber on jack and try planes. Also you can’t square up the edge of a board without a camber. Or if you can, I have no idea how...
@BigDaddy-ms7gm
3 жыл бұрын
I like how you set your bevel then dress the wheel and changing your setting. Brilliant!
@robertlangley258
6 жыл бұрын
I swear! All this time I thought I was the Worlds best Blade sharpener! Absolutely loved this video. Well done, well done
@ianbeckett2427
7 жыл бұрын
Love your videos Matt. It feels like I've watched a thousand sharpening videos but its never really worked for me. Somehow though yours are different and I think I'm starting to get there.
@MattEstlea
7 жыл бұрын
Lovely! It's all about simplifying and making the process efficient. Best of luck and be sure to send me any questions. Cheers Ian!
@malcolmoxley1274
6 жыл бұрын
Matt,well done on a comprehensive lesson,you are a natural teacher and you have now got a subscription from me
@seanporter113
3 жыл бұрын
I find your instruction thorough and precise. I’ve become a new subscriber. Thanks man
@lokisullivan469
5 жыл бұрын
Great great video. Matt showed how to create a really nice quality edge with the help of a few aids. Purist will say you don’t need aids, but they all use “tools” to get the job done. I’m all for using the best tools to produce the best results without spending all my time preparing my tools. I’d rather be cutting wood. Yes, it is great to learn to freehand all your blades but not everyone is interested in that art. And yes it is an art beyond just tool basic maintenance. I personally would like to see someone do in depth analysis under microscope to see the differences between the edge of a pure free-hander and the edge produced with aids. I think the difference would be astonishing! Again great video Matt. It’s very close to how I learned: 300/1000 diamond plate, 1000/6000 King Stone and a Strop. Seeing how precise your primary bevels are, makes me want to buy a grinder as well.
@eagleonone
7 жыл бұрын
Excellent presentation. Clear, concise and right to the point.
@knippo
7 жыл бұрын
Really love your videos mate, can't wait to watch next about setting up the plane!
@peterisrael2012
6 жыл бұрын
Ben Askren is a man of many skills .
@rider660r
3 жыл бұрын
LOL right.......... You may want to go look up Paul Sellers...
@ericmoody3944
3 жыл бұрын
This guy actually has the look of a fighter unlike Ben.....
@rajerrell
3 жыл бұрын
Check out Rob Cosman for real woodworking tips. 😎
@MyVinylRips
6 жыл бұрын
Thank you so much. Crystal clear as always!
@steh8217
3 жыл бұрын
As a new woodworker, I originally thought I can save few £ on a honing guide and free hand sharpen like loads of guys do. But I could Never! Get plane irons or chisels truly sharp. I was buying old vintage tools at car boot sales etc and didn’t realise how much work they needed. But few £ on a honing guide and now I see what sharp is like, and it is consistent 😁
@tomwright2601
Жыл бұрын
I have learned so very much from your videos! Keep it up Master Matt!
@tonyrowan3192
7 жыл бұрын
Keep 'em coming Matt- nicely done. Thank you.
@MISANTHROPE1964
6 жыл бұрын
Matt, Would love to see how you flatten the backs of chisels and plane irons.
@JewellerybyPaPe
7 жыл бұрын
Love your videos! Great tip to develop the camber on the plane blade, I will implement the technique next time i sharpen my blade. Stay awesome!
@MattEstlea
7 жыл бұрын
Glad you found it useful! Cheers Patrik!
@shonuffisthemaster
6 жыл бұрын
good videos, i usually learn something and i like how you start from the verry begenning, not assuming your viewers have any prior knoladge. verry friendly and step by step approch that im sure takes the intimidation out of these subjects for allot of people. I know sharpening can be challanging for many people and is something woodworkers tend to put off untill their tools are unusably dull, then get frustrated with how much work the edges need and give up before there sharp. To this point, i think making sharpening faster and easier is the way to go, so you do it more often. I think people really need to learn to sharpen by hand without jigs. i see all the time that your spending not only using jigs in the first place, but even switching jigs in the middle. fiddling with all that stuff takes allot of time and i think is discouraging to sharpening more often. you could also be spending that time taken up by setting up the jigs to get a really good edge. i know the title says "stupid sharp" but ive sharpened enough to know the edge your getting after just knocking the burr off with a 6k and on to a bit of stropping is nothing to write home about. one of the big disadvantages of using jigs is the inability to work on the back side and then go back to working the bevel. the edge needs further refinement after the burr comes off, more than just stropping will do. I know your passionate about woodworking, i encourage you to step up your sharpening game and learn to freehand.
@pacmandrugs
6 жыл бұрын
I just free hand it on a belt sander. As long as you keep the belt wet, it doesn't overheat at all. It seems to give a great hollow ground, and just about as even as any jig could produce.
@allanwelsh7620
6 жыл бұрын
real handy tools to sharpen blade. Nice job.
@bradleytuckwell4854
2 жыл бұрын
Great advice thanks
@pepperbird67657
4 жыл бұрын
Hot take: plane with an inverted curve so you take out more on edges and less in the center
@iiiiiihaa
6 жыл бұрын
Stupidly perfectionist. Very impressive. Thumbs up.
@xtraMTpockets
7 жыл бұрын
New sub here, love the way you do your videos, and look forward to your next video, thanks mate
@MattEstlea
7 жыл бұрын
Cheers mate!
@jamescampbell7780
3 жыл бұрын
Stanley make a guide with two rollers which prevents the plane iron from tipping sideways unlike the single roller type.
@robwahl7512
6 жыл бұрын
Thanks for being awesome and making cool videos. I’m learning lots. Never mind the pronunciation police. Happy new year.
@MattEstlea
6 жыл бұрын
Thank you Rob, very much appreciated! Happy new year to you too!
@spamatron6471
2 жыл бұрын
I have no interest in any sort of wood work, but I can watch these videos for hours
@rolandosalvania4273
5 жыл бұрын
i like the hair better lol. nice work. more power bro
@daddio1491
Жыл бұрын
Hello Matt. I’ve been new at sharpening chisels and plans. I noticed the stop block with numbers on then. Do you have a video on how to make that
@jamesgray3057
3 жыл бұрын
excellent vids Matt, could you show us how to make that palm screwdriver please
@DaxOneTouch
5 жыл бұрын
Nicely done
@tom314
4 жыл бұрын
As always a well done and very useful video, do you fancy doing another one sharpening router plane blades?
@FJD333
5 жыл бұрын
Reading some of the comments on this video suggests that a point has been missed. So what if Matt has every tool at his disposal. The fact is he still knows what to do with them. He has a good pair of hands. That's a given. But in this age of You Tube "woodworkers" where some of them are just plain rubbish, it's somewhat refreshing to see someone demonstrating a technique which will be around for just as long. It's a simple fact of life, that if expertise in any field is not passed from one generation to the next, then it will be lost forever. Don't knock what he's doing. It's not what you need to do. But if you wanted to, I think this is a pretty good start.
@russruss2446
6 жыл бұрын
Useful info. Unlike many videos, this offers something new and useful. I learned from Paul Sellers, good stuff. But freehand sharpening only works if you do it all the time, otherwise you loose the edge. Your ability to judge the angle fades away, and there’s no point stroping an edge that isn’t already almost perfect. So unless you’re a 1920s craftsman or Paul Sellers, use a jig.
@ehisey
6 жыл бұрын
I don't know about that. the blade as it came out of the plane would take about 15 min. start to finish tops with 3 stones a strop. Less mess, less setup, longer life of the iron, and you could still use a guide if you wanted too.
@pilobond
6 жыл бұрын
I am by no means an expert or pro. I have a day job, I don't do sharpening "all the time". Maybe I would sharpen a few blades a month max, when I am in the mood for woodworking that month? But Paul Sellers method works for me. Sharp, mirror polished edge in 10 minutes or less with mimum tools (really 3 diamond plates and leather strop on 2x4), no machines. And yes, if cutting hair on back of hand is "stupid sharp", it does get "stupid sharp" too. A guide just gets in the way. (I bought one, but haven't used for more than a year.) The point is that no higher authorities above decided that "25 deg" is the "proper" angle. As long as you are close enough it doesn't matter.
@TheBaseShop
6 жыл бұрын
Great video. just a suggestion for you though, when you mention your previous video, have a link to it in the corner or something. makes it easier to find that video and we end up watching more of your stuff :) it might just be me, but I don't find it easy to search through videos to find the one you're referencing.
@Richard-yr5zj
Жыл бұрын
Thanks for the great tutorial. Do you have a second favorite leather strop? The one you link to is no5 available. Thanks.
@maustinau
3 жыл бұрын
Sweet! So all I need is a $150 diamond plate, a $700 Tormek, $300 in Japanese whetstones and I'll be able to get my $100 plane iron hella sharp. Really, good on you for making this but anyone in a position to have all that probably won't need a video on how to use it all. Where's a video for guys who have some sandpaper, a flat surface, a honing guide and maybe a stone or two?
@philparrish8892
3 ай бұрын
I am struggling to find a wide enough whet or oil stone for my No.7 plane blade. I saw your links so that I can find from Axminster. Do I really need a lapping plate and what is it for?
@geeborg6912
Жыл бұрын
Matt, I’ve watched all your videos and picked up quite a few tips I’m glad to say. I’ve just received a Hock plane blade and chipbreaker and was all set to sharpen the chipbreaker until I saw your advice NOT to do so as this could cause problems. Apart from saving me the bother of sharpening the chipbreaker, could you elaborate as to what problems might arise by sharpening said chipbreaker - just curious….. MVH
@matrixmodulator
4 жыл бұрын
6:43 how does this stop block made? is there a guide to know where the end of the jig goes? you mentioned someone doing a video about it? link ?
@high-velocitymammal5030
3 жыл бұрын
It's just a jig to quickly tell the distance between the edge of your chisel or plane blade, and the mouth of your chisel guide/ holder. A given distance between the two should always give the same sharpening angle. I just use a ruler to measure, because I know that for my Stanley chisel holder, 25 mm between the mouth of the holder and the cutting edge of the chisel means a sharpening angle of 25°.
@yomomz3921
3 жыл бұрын
So, uh, I tried the ol' shave the hair off of your hand trick after sharpening. Well, the corner dug in ever so slightly... and I shit you not, the blade started taking a ribbon out of my hand. I saw it, just a gossamer wisp of a thing, and for a split second, I was mesmerized by the sight. I never even felt it. My hand didn't even know to bleed until a few seconds later. It wasn't deep at all, but yeah, the method gets a blade sharp as fuuuck. - (I suppose that particular blade has officially been christened).
@adelker4884
5 жыл бұрын
Generally speaking, I've noticed that once one person posts a negative comment, many others will follow suit--and vice versa !
@richardsinger01
5 жыл бұрын
Adel Keryakos yes, often making exactly the same comment. Strange, isn’t it?
@garethev5866
4 жыл бұрын
It makes em brave
@adelker4884
4 жыл бұрын
@@richardsinger01 Yup, very strange, indeed. I like the Chinese proverb that says, " Instead of cursing the dark , light a candle !" Ps -- Sorry for the late reply. I saw your comment just a few minutes ago.
@adelker4884
4 жыл бұрын
@@garethev5866 Same apology to you as I said to Richard Singer. I got a notification from KZitem that I had a reply... And yes, they hide behind the anonymity of KZitem and criticize good people who do their best to share their ideas and expertise... I see a lot of that in comments on music videos ( in which case, it's basically bias and hate).
@gavinistheawesomest
Жыл бұрын
So I have a knife sharpening jig. We are talking mirror finishing knives. Would that be good for this?
@RONNIEJNZN
5 жыл бұрын
When I do grind, which isn't often,(not a tormek, bench grinder w norton 3x I grade and jigs) I gently push the blade to the stone with an ice cube. I dont overgrind/overheat and always finish on dmt plates but its added insurance
@jamescampbell7780
Жыл бұрын
I’ve not seen a chip breaker which is flat and sharpened. Is that an American or Canadian version?
@keuckwh8979
6 жыл бұрын
8:42--Pulling the blade on the flat stone creates a burr. Pushing the blade on the flat stone prevents the forming of a burr.
@leafthatfalls
5 жыл бұрын
He's got water stones not oil, they're softer. So if you push you run the risk of gouging your stone and having to spend a bunch of time flattening the stone again.
@ziggen78
3 жыл бұрын
Complimenti per i video!! Olia le pialle che sono tutte arrugginite poverine!!😜😜🤗🤗🤗🔝🔝
@fergusrb
2 жыл бұрын
I am looking at getting the Stanley Sweetheart low angle jack plane. Do you sharpen that the same way with a 25 degree primary bevel and a 30 degree secondary Bevel?
@markdyke3381
6 жыл бұрын
Nice video Matt, shame about the neg comments.
@stevenlarsen1691
2 жыл бұрын
What do you coat the blades and your tools with to stop them from rusting? Just WD 40?
@JustTony72
4 жыл бұрын
What would one do if their stones aren't as wide as the plane blade besides from buying new stones. Like if you sharpen one side and then move over to the other side and sharpen again. then wouldn't the middle have had more passes than the sides?
@LordNPS
7 жыл бұрын
There is a great "in between", between hand sharpening the coarse bevel and tormec. Use a bench grinder with the big back slow wet stone, works fine for getting that primary bevel, and they are very inexpensive (35€). You WON'T ruin the steel. The simplest wood block with an angle cut on the end works fine as a jig too. Best value solution I think.
@DogBig1793
4 ай бұрын
my name is Eric Tyler when I'm sharpening my hand plane blade I'm noticing that the left side isn't sharpening as fast as the other side. I've tried to put more pressure on that side with no success. what am i doing wrong?
@KSMike1
6 жыл бұрын
I too own a Tormek, but am finding it an awfully expensive and space-consuming tool if only used for primary bevels.
@MattEstlea
6 жыл бұрын
Yea I know what you mean. I ended up buying a kitchen knife jig to help it earn its place. Perhaps look in the local area and see if anyone needs sharpening services for chisels, knives and plane blades. We have a lot of people at come into the store where I work needing blades reground.
@giacomobattisti7943
6 жыл бұрын
But if you do woodturning or if you work with hard woods with a lot of tools it pays itself, i mean, i need one and i know it's potential (my woodworking school has two t8s) and i'm really gonna get one! Of course for primary bevels it's non necessary but you sharpen everything in a perfect way till razor sharp
@ianmoone2359
5 жыл бұрын
Tormek is over priced & redundant outdated outmoded technology since Electroplated steel grinding wheels coated with CBN (Cubic Boron Nitride) came into production for your bench grinder. 2nd in hardness only to diamond, they grind COLD for High Speed Steel & Tool Steel. You can hold your hand near the cutting edge being ground & it barely gets warm to the touch. It WONT make the corners or edge turn blue & ruin the temper of the steel the way a aluminium oxide wheel does! There’s no longer ANY need for wet grinding! Diamond wheels are still used for tungsten carbide & CBN for HSS & Tool Steel. Diamond wheels clog up with grinding swarf & then heat up & need to be “cleaned” using a aluminium oxide stick, whereas CBN doesn’t clog or get warm or need cleaning. CBN wheels will make Tormek systems redundant pieces of over priced junk you can’t give away let alone sell.
@diowk
Жыл бұрын
matt messed up in this video. he said that he sometimes changes the angle of his secondary bevel to 50 to reduce tearout. that is a bevel down plane. changing the bevel angle doesnt change the cutting angle. what he described only works with a bevel up plane. if you want to increase the cutting angle on a bevel down plane, you need to introduce a back bevel, not increase the bevel angle.
@dunlaoghaire1000
5 жыл бұрын
What are the exact brands and specifications of: 1. Diamond stone. 2. Waterstone. 3.Blade guide. 4. Strop 5. Paste. and if it's anything else. Thanks.
@lukewhite9237
5 жыл бұрын
1. DMT Lapping Plate (don't use it for sharpening, just for flattening waterstone) 2.Bester Imashi 1,000/6,000 Combination Waterstone 3.Lie Nielsen honing guide with long jaws 4.Cornell Double Sided leather strop 5.Axminster Brand Superfine Honing Paste Also get a stone holder or non slip mat, and a spritz bottle for water, and watch Matt's video on how to make a protrusion stop out of plywood
@metzessible1271
3 жыл бұрын
Just curious, but would I follow these directions for all plane types (Assuming down the road I end up with all the other kinds aside from the low angles or whatever)?
@donaldroberts7055
3 жыл бұрын
thankyou
@jessestrum
6 жыл бұрын
thanks matt usefull tips
@boozoochavis7506
5 жыл бұрын
This is a good video, but I wonder how much different it would have been if the cap would have been set at £100 worth of kit? That would be a very different video and certainly more in line with many of the people checking out this video. How many people really have access to this much dosh?!
@tworiverflyfisher
Жыл бұрын
Matt, I saw your Tormek, which model do you use? is the 8 better than the 4?
@kaiprice7856
4 жыл бұрын
Hi Matt great video on sharpening a plane blade very useful , how much is the lapping plate ?
@duartepaintinghandymanservices
5 жыл бұрын
for his age he sure knows alot, wonder who was the master who taught him? cool vids!
@leafthatfalls
5 жыл бұрын
He went to school for this, I think it mentions it in some descriptions.
@shingshongshamalama
4 жыл бұрын
What if I don't have a grinder?
@250-25x
5 жыл бұрын
So sharpening my chisel blades on the macadam in my driveway is a bad thing? I dunno...I only need to use a 3lb mallet to getem to cut! G>
@saltygx
7 жыл бұрын
Great video, thank you for sharing!
@powerobxxx
6 жыл бұрын
Great video Matt, very very interesting, I am just a hobbyist sort of guy and will never have the sort of gear you have but it does give me an insight on where I should be aiming at rather than just hammering my blades into a grindstone and hoping for the best :) can I send my blade to you for sharpening please, you can make a video of top ten shittest plane blades LOL
@rickhickman2730
4 жыл бұрын
When it comes to the ruler trick producing the micro back bevel, at what point do you need to either flatten the back? Or grind the face bevel away enough to remove the back bevel?
@dodoit7907
4 жыл бұрын
So I started watching this series through your website, and you keep saying I talked about this in my previous videos. Which you didn't if you follow the series on your website, I quess I will see if I get to finding them in your youtube list. But I thought just to let you know you're referencing to things that are not on your website.
@davidsteele3037
4 жыл бұрын
A Tormek T8 is nearly £600 and a linisher is £450 (Axminster Trade Ultimate Edge System). Is it worth paying the extra for the Tormek if I'm only going to use it to regrind the primary bevel? I notice the linisher will heat the blade if not regularly quenched in water.
@thegreener196
6 жыл бұрын
awesome video, as for all the old schoolies I agree it great to learn the old way to do things so we dont forget but come on! muddy waters invented electricity! (I stole that last line)
@rickschuman2926
3 жыл бұрын
I use a bit of broken sandstone grinding wheel, a piece of slate, both lubricated with water, and a leather strop. No jigs, just well trained hands. This will not work with high carbon steel.
@spacemansabs
4 жыл бұрын
What do you do if you’ve watched this video AFTER you’ve contaminated the fine side of your stone?
@frenchaccent540
4 жыл бұрын
Great video! What is this door knob looking screwdriver you use to tighten sharpener ?
@kljw66
3 жыл бұрын
Great video. does this principle apply to. blade used in a bevel up plane?
@betoen
6 жыл бұрын
Man! Too profesional. Over the top for me that only have a roughly 380 stone, hahaha. But, nice work.
@basgoossen
6 жыл бұрын
Just check out Paul Sellers for plane sharpening, a much sharper job with more experience and a lot less money involved ;-)
@Natedoc808
6 жыл бұрын
thank you kindly! Cheers.
@jettkeyser9909
6 жыл бұрын
Matt...Could you post a clear plan for the registration of the honing guide for the angles used...25 and 30...I am referring to your wooden sharpening jig...
@MattEstlea
6 жыл бұрын
Here you go mate :) kzitem.info/news/bejne/qmpnnYqMqJlhdZg
@talbrott
4 жыл бұрын
thanks
@parvusswoodworks9664
5 жыл бұрын
How can I be sure that the blade and the side is 90 degrees? I use a tormek and sharpening stone with honing guide
@stevev2414
6 жыл бұрын
Good video. I've been laboring for a while over whether or not to get a tormek and, in particular, if it supersedes or compliments the use of water stones. Its clear from your video that its part of your sharpening toolkit. Was wondering what you see as the main advantage of the tormek - is it just speed? Would you use Tormek to help with flattening the backs of 'ly' neelsen chisels?
@ehisey
6 жыл бұрын
I have access to one, and the main thing I use it for is repairing damaged blades. Day to day honing, is faster and simpler with a set of stones. I would not try to flatten anything on a wheel, it by nature creates a curve. That is best done a large flat diamond hone.
@michaelballinger6419
6 жыл бұрын
Don't by a tormek just learn to sharpen on any stones you can find. A little inexpensive honing guide will help get you started (I used to use them) now I just freehand sharpen it's so fast to do, doesn't take up any space in my workshop and I get shaving sharp edges. Takes 15 minutes to sharpen my set of 6 bench chisels and my smoothing plane iron.
@michaelcogger5725
6 жыл бұрын
Hi Matt. Are the bevel angles the same for Bevel up planes like the one you use in your shoulder plane video. Also do I put a secondary bevel on my new Axminster 271 router plane??. Great vids keep em up. Thanks.
@jaysonschmitt888
7 жыл бұрын
great videos
@GNU_Linux_for_good
6 жыл бұрын
04:52 Holy cow! There's a jig for straightening out the stone. I never saw doing it that way.. 08:00 Always *drag* - never push. Right?
@mfcman2k7
5 жыл бұрын
would make a good video showing how you would look after your tools such as getting the rust of them as you said in the video you would make a video
@mightymike9353
5 жыл бұрын
Hi Matt, can you please tell me where I can get the screw driver you used to tighten the Lie Nielsen honing guide from. Thanks.
@Ashe_Fenrir
5 жыл бұрын
its from lee-valley (if you google it they've got them - or highland woodworking)
@jettkeyser9909
6 жыл бұрын
Excuse...stupidly fast...but that does not quite work...Appreciate the time you have put in Matt...Clearly shows in all your work...I am just finishing up what I would call a huge slab table...spalted alder...8 feet by 42 inches...about 2 inches thick...My 5 year old grandson and I planned the 3 slabs down to what I considered a good enough level...I could not imagine all the dust had I used a sander...Thank you
@Gwynbuck
4 жыл бұрын
What is the point of a primary bevel?
@benjarvis2424
7 жыл бұрын
Hey Matt great video, I remember using the tormec during my training, just a weeee gripe noticed it in your other video as well, it's pronounced lee nielson, try and make it to one of their open days such fantastic tools :) keep up the good work!
@MattEstlea
7 жыл бұрын
Oh dammit I always get confused with that. Everyone says it differently I never know which pronunciation it is! I really want to come to one of their open days, it's on the list! Cheers mate
Пікірлер: 335