Absolute life saver for telling me about the black wire to the right!
@normanlaw8191
3 жыл бұрын
Thank you for the informative video. Do you also know how to setup the fail-safe in case the transmitter gets switched off?? Thanks in advance.
@shred__dad
2 жыл бұрын
Would love to know how to do that as well. Got one receiver that works ok, the other does the thing when i turn the receiver off, engine starts to run. Thats frustraiting
@fubuh8r
2 ай бұрын
I just bought a Rlaarlo AK 787. Just found out that it is a DumboRC X6PM radio setup. The car has lights and DumboRC has a receiver that has the led controls built in. My version of the car doesnt have controls for the turn signals and brakes. They stay on. With some re wiring i can get it to work now with the DumboRC receiver. Thanks for the binding video.
@poolboyq9752
Жыл бұрын
Just got this and I’ve been searching all day for a video like this! Simple and to the point. Thanks brotha! 🤘🏼
@doylecholesterole1927
Жыл бұрын
Hello, just an outside question. Does increasing the voltage of the remote help with better signal and range?
@GamezOfWar
2 ай бұрын
Yea, mine doesn’t work
@joshuajuarez3471
6 ай бұрын
Bro. I been trying to figure out why nothing works. Once you said black wire in right. It worked. That was my first question since this is my first RC. We are not dumb dumbs. But orientation matters. The more spins forward or back that’s just swapping motor wires.
@MysterP
5 ай бұрын
After 2 years or so my receiver wasn't responding, pressing the button reset the thing from Orange to Green Orange being gyro on green is off. But now the button doesn't even want to do any thing any thoughts or pointers? Everything was working great until, well that's just it nothing happened it was out of nowhere
@lynnashley6247
3 жыл бұрын
Thank you, for a concise, clean and on the mark video. I'm surprised how little info I can find on this RC receiver.
@teamjbhobbies
3 жыл бұрын
No problem. Hope it helped!
@ChezzOnBass
Жыл бұрын
If only the chinstructions showed you how to put the wires into the receiver! THANK YOU! I was close to packing this whole thing up and sending it back!
@the.just.able.biker67
10 ай бұрын
Same here!! 🤣 I'm new to rc and I couldn't believe how vague the instructions are with everything. I'm building a Tamiya kit, which has very detailed instructions on how to build it, but when it comes to the electronics everything is vague. Apart from the warnings about connecting things the wrong way and the damage it could cause. 😡
@redndeyes
2 жыл бұрын
1 turn 2 burn Is how I remember lol
@doylecholesterole1927
3 жыл бұрын
Hello, you explained the video well for a starter like myself. But I have a question, I bought this transmitter. But my car has an ESC/RECEIVER combo (HBX 16889). So I need to purchase a separate esc. But on the website it also says you need some kind of program card??? Do I still need that if I got this transmitter? Sorry for long question.
@teamjbhobbies
3 жыл бұрын
A programming card is something you can plug your ESC into to set up the settings. With a lot of ESCs, you can set up the settings without using one by listening to beeps and pressing buttons. Each ESC brand would have its own programming card you could purchase separately if needed. I think it might be a challenge fitting an ESC and the Dumbo X6FG receiver on a 1/16th scale car, but I would love to see it if you do make it work. Let me know!
@doylecholesterole1927
3 жыл бұрын
@@teamjbhobbies thanks for reply. But can I purchase any brand esc and any random program card? Some shops on AliExpress only have the esc with motor, and others have the card that go with it
@doylecholesterole1927
3 жыл бұрын
Sorry am still new to all of this so I don't have a clue what to do. And with this lockdown, all I can do is get help from youtubers!
@teamjbhobbies
3 жыл бұрын
@@doylecholesterole1927 Your ESC would need to match the type of motor you have. If you have a brushless motor then you would want an esc for brushless (vs brushed). I would suspect your car came with a brushed motor but you would have to check your manual. A quick search on amazon for "esc brushed 1/16" brings up some options. The program card would need to work with the esc you buy. So if you are going Aliexpress you never know what exactly you will get vs if you went with a name brand you know they would work together. Then again if you buy an esc that you can program without a card that is fine too. And you may not even need to program it at all if you just want the basic settings.
@doylecholesterole1927
3 жыл бұрын
@@teamjbhobbies @Team JB Hobbies okies, thanks for the tips. The HBX are brushless. I'll try without the card first. I can always wait if I do need it. But that ka again
@konawantv
3 жыл бұрын
what does the light mean if it turns green ?
@teamjbhobbies
3 жыл бұрын
Green means that it is normal mode (non-gyro). Press the button 3 times to make it gyro mode.
@mitchellpeall9538
Жыл бұрын
Very helpful thank you.
@joshuajuarez3471
6 ай бұрын
Again the receiver needs a label or one way plugs 🔌
@paulrakis
2 жыл бұрын
Wow didn't know it's so easy great video bro. I'm using my Dumbo x6 on my outcast 8S exb. I keep cutting the receiver wire even with destroyer in place any recommendations
@CleanCutLawncare24
9 күн бұрын
mine didn’t work
@shadyhazza
10 ай бұрын
2:00
@shadowb195
Жыл бұрын
hi, but how on your controller is a blue light, on mine it blink blue and white, I don't understand and when it blink like that only the wheels on my car work, does it mean that the engine is dead, the engine is brushless or, if you can say something about it,thank you👍
@teamjbhobbies
Жыл бұрын
If your transmitter light is blinking you could need to just replace the batteries. Try a fresh set of good-quality batteries and see if that resolves it.
@shadowb195
Жыл бұрын
@@teamjbhobbies ok, thanks, I have new batteries, I'll try them and write how things are, thanks again
@shadowb195
Жыл бұрын
@@teamjbhobbies new batteries but still the wheels don't turn, I think the engine is dead, I don't think there is another explanation.
@bra1nc417d
2 жыл бұрын
I just installed this system and the receiver binding button just fell right off. I simply tried pressing it in with some tweezers and it fell right off, barely any pressure. I could feel the button click right before it broke off, so the amount of pressure to simply press in the button, was enough to break the switch right off. Well, another ones on the way. At only $18, why not try again. Sure am hoping the next one isn't a total piece of garbage. Get what you pay for, I guess🤷🙄
@southwarzone8894
2 жыл бұрын
Thanks i’m a beginner to the rc world and just bought this.
@Sam-nz2zs
Жыл бұрын
1 to turn and 2 to burn
@mzmhrc1274
2 жыл бұрын
hi mate! do you know why my dumbo remote operate in reverse for steering and throttle when i'm finished binding.already tried for few times result still same.switch also have been set to normal.
@slave3rd
3 ай бұрын
Which X6 transmitter is this? None of the Dumbo X6 I see around has this red painting
@borderjs
3 ай бұрын
The strangest thing. The red version is no longer produced. The supplier told me that China made a new rule and red was no longer allowed (this was quite awhile ago at this point).
@slave3rd
3 ай бұрын
@@borderjs all right then, nothing we can do. Thanks for the repy!
@samcourtrc6767
3 жыл бұрын
Flip bro Thanks for sharing this about the dumbo rc
@teamjbhobbies
3 жыл бұрын
No problem! This is one of the most common questions we get about it.
@samcourtrc6767
3 жыл бұрын
@@teamjbhobbies 100% bro thanks again
@johnwhoa1187
Жыл бұрын
perfectly explained video, for that i thank you.
@CmwSpeedrunUk
2 жыл бұрын
This is a great video 💪🏽🇬🇧👍🏽
@codyviera92
2 жыл бұрын
Mine will bind the receiver won't blink no matter how long I hold the button
@norhafizuljohar5975
3 жыл бұрын
I just bought transmitter x6 and x6f receiver. Can i change from old x6f to x6fg gyro receiver with same x6 transmitter ?
@nej2902
2 жыл бұрын
Yes you can!
@kenjidalit995
3 жыл бұрын
What is that car
@teamjbhobbies
3 жыл бұрын
This is an Arrma Granite 3s BLX
@kenjidalit995
3 жыл бұрын
@@teamjbhobbies those are nice tires
@Sheldinator
2 жыл бұрын
can you show a video how to setup the Ariel for the receiver. i have no clue what to do to have it neat. thanks
@teamjbhobbies
2 жыл бұрын
I would think that is very dependent on which car you are installing it into. Mine has a tube where it runs through. I think I would just run the wire how your original receiver had it.
@g.b-MTB-trail-jumps3062
2 жыл бұрын
Great job cham
@yotaiji012
Жыл бұрын
Does it pair with other brand receivers?
@aqilzafri13
2 жыл бұрын
Thanks for the video!
@maysonthomas6833
2 жыл бұрын
Do you know any videos that show this radio and receiver in a nitro rc?? Trying to figure out church channel the battery goes In and the glitch buster
@teamjbhobbies
2 жыл бұрын
Hi, I did a little searching around and I think you have to have a different receiver to use this radio with a nitro car. I found the DumboRC X6YCG receiver is advertised for Nitro but I am not 100% sure how it differs or how to wire that. Sorry I could not be of more help.
@Henry_the_hen
2 жыл бұрын
Thanks it worked
@germainbilodeau1826
2 жыл бұрын
Thank you
@martez752
2 жыл бұрын
Can I use this dumbo transmitter with my stock servo or you have to change the servo too? I have a typhon 6s
@teamjbhobbies
2 жыл бұрын
You do not need to change the servo. You will just replace the receiver.
@martez752
2 жыл бұрын
@@teamjbhobbies Thanks
@Th3Mafia
2 жыл бұрын
your steering servo is very slow :o
@teamjbhobbies
2 жыл бұрын
Which servo do you like to use? This is just a random basher to demonstrate pairing. :)
@simonshoot5
2 жыл бұрын
Whats the gyro? Do I need it on or off? Great video
@teamjbhobbies
2 жыл бұрын
A gyro receiver stops the RC car from spinning by making adjustments to its steering so it can move in the direction you want it to. The more throttle you give, the greater the disbalance between the front and rear of the car; the gyro receiver counter steers the RC car. The gyro receiver keeps the RC car’s tires aligned in the direction you choose; regardless of the track traction and external force, the gyro precisely maintains the direction you set the car to move in. Basically, if you are about to spin out from a sharp turn or gunning it in rough terrain the gyro adjusts the steering for you to keep you going straight. I personally turn it on and just the channel 6 knob to adjust its intensity. You can set it to 0% on the knob to disable it (practicing for a race maybe). Or set it higher if you are just having fun and want to gun it without worrying about it. Just a quick note if you set the gyro too high you might see odd behavior like twitching.
@simonshoot5
2 жыл бұрын
@@teamjbhobbies ahhh ok thank you so much for your quick reply
Пікірлер: 68