Good information, but if you spoke, it would be even better!
@walther9161
2 жыл бұрын
Thank you.!!! I think most of the watch video makers assume we novices know this part. I had no idea to set the fork to the entry position . Awesome
@thewatchsmith2773
2 жыл бұрын
You may be interested in a second channel I am doing which is geared toward teaching watch repair from the ground up. Here is a link. kzitem.info/rock/XV8h3I9pnfZuDpg6xEM_8w
@toolzshed
Жыл бұрын
That impulse jewel arrghh!!
@amandagelien9612
Жыл бұрын
You saved a lot of balance springs and jewels with this video and needs to go viral 😃
@ramazanbaris2349
Жыл бұрын
I broke my third mechanism learning to install the balance wheel by bending the hairspring. Apparently, didn't take my time enough! I'm not complaining, I'll keep screwing up hairsprings and some other shit until I master this f*** work!
@paulwilson3434
2 жыл бұрын
Best explanation
@cristianvera8506
2 жыл бұрын
That was very helpful mate,noice thanks 🙏 🇦🇺
@captainhaddock2137
2 жыл бұрын
The problem I have is you can't see the impulse jewel from the top so getting it between the two thind is a pretty hit and miss affair
@sheralam920
2 жыл бұрын
you wouldn't miss it if you keep the pallet in its entry position and rotate the balance wheel in the shown direction and then the impulse jewel will move towards the pallet fork. Moreover, while the balance wheel is oscillating the impulse jewel is not always in contact with the pallet fork. The jewel leaves the fork while it swing away and catches it up again while swing towards the fork.
@philipbrailey
8 ай бұрын
Cat got your tongue.
@Pindi44
2 жыл бұрын
Excellent! Thank you.
@philipbrailey
2 жыл бұрын
It’s hard for me to read as I am a slow reader. I miss out on the picture. It’s a shame you can’t speak.
@puterami123
Жыл бұрын
You can hit pause.
@nikolaoswatch7489
Жыл бұрын
Dear friend, I have bought a Chinese watch with a in-house movement. That was smart. :-) The watch run for few seconds and then stopped. Then again the same. Then run for few minutes and stopped permanently. I saw your video and thought I found a solution to my problem. I did it 3 times and then it run again for a whole minute and stopped again. Maybe you have any suggestion what else I could do, before dismantling it totally, which I will do for the first time in my life. :-) But again I have a stopped watch which I can not service where I live. Maybe you can give me your email and I will send you a link to the full video of what happened to the watch so far?
@wyliecoyote1
Жыл бұрын
I like it's a lesson on one circuit within the watch movement, not too much at once. I'm trying to learn what I can before I try to disassemble a training aid pocket watch that has no hope of ever to work again. That way I can't break it.
@TheZhvanec
2 жыл бұрын
Definitely best explanation
@alexhamilton9566
2 жыл бұрын
Thanks brother
@puterami123
Жыл бұрын
Didn't know if I was going to see how to install a balance wheel or spring.
@brunotulliani
Жыл бұрын
I am building a parts watch "as st 1960/51" that what I believe is a three tab "SHOCK RESIST" spring. How do I gain access to the chaton a jewel? I would greatly appreciate your help. Thanks
@watchrepairtutorials
Жыл бұрын
I am unclear about what movement you are talking about
@brunotulliani
Жыл бұрын
@@watchrepairtutorials The Forum Watchuseek I posted some pictures. A lot of the posts mention the cap jewel can not be removed. Plan B for me is to use an oiler.....lol
@neburajan2841
2 жыл бұрын
Recently I got a new watch which has a open back case, i noticed that the balance wheel will slow down when the second hand is in the 7 to 10 o'clock position and then speeds up again, is that normal or should I get in touch with the watch maker.
@watchrepairtutorials
2 жыл бұрын
Yes it’s that noticeable visually, yes I would have it looked at
@CACOPHONIE
2 жыл бұрын
thank you vary much ❣️
@andytachibanalover9495
2 жыл бұрын
very nice-thanks
@louislapointe8996
2 жыл бұрын
Would the balance wheel still be working without the safety pin (or broken s.p.) on the pallet fork^
@watchrepairtutorials
2 жыл бұрын
On the bench yes, but as soon as the watch receives a small bump it will stop. The guard pin is part of the safety system of the watch
@louislapointe8996
2 жыл бұрын
@@watchrepairtutorials Thanks it's appreciated
@helmuthrendl6560
2 жыл бұрын
Thank you for sharing this Video. You're a very good teacher
@thewatchsmith2773
2 жыл бұрын
Thank you so much! You may be interested in my second channel called “It’s About F*****g Time.
Пікірлер: 34