Anytime! It's great to hear that you found it informative. 🙂
@iblesbosuok
5 ай бұрын
Thank you for your share, sir
@crutchfield
5 ай бұрын
Thank you for commenting, and enjoying!🥰
@martinblouin3639
Жыл бұрын
great tip! thanks
@crutchfield
Жыл бұрын
You're welcome! We are glad this video helped!!
@walters1144
Жыл бұрын
Hi, does it matter in which direction the capacitor is soldered into the positive wire? I'm not sure wether it has polarity and would cause issues if soldered in backwards. Thanks.
@crutchfield
Жыл бұрын
Bass blockers are not directional, so the orientation of the Bass Blockers on the positive and negative speaker leads is not important. Polarity is important; the white wire is positive and the black wire is negative.
@popcornplaya83ify
Жыл бұрын
👍🏾 nice vid thanks
@crutchfield
Жыл бұрын
Thank you, Johnny!
@kfash5198
3 жыл бұрын
I have a question. Can you install a "in wall speaker" in a concrete wall?
@kavneetraj5041
Жыл бұрын
No
@AlexSchwartzATV
2 жыл бұрын
Do you happen to know if bass blockers could be installed for the door speakers on a 2003 GS430 with Mark Levinson/Navi?
@crutchfield
2 жыл бұрын
Bassblockers can be installed onto the woofers in the doors. Bass on the size of the woofer, we recommend this model bassblocker: www.crutchfield.com/I-rYALc227/p_007BB600/item.html
@stives466
Жыл бұрын
Hi The FRONT IN wires are white/white-black and grey/grey-white but who is left and who is right? The same for the REAR IN wires which are green/green-black and purple/purple-black but which is left and which is right? This is not stated in the documentation
@crutchfield
Жыл бұрын
Which wires go to the actual Left/Right speakers should not be a necessary detail to install bass blockers. You should be using the same brand/model speaker for both the left and right audio channels in say the front of the vehicle. This means you would be using the same model bass blocker for both of the front channels (same for the rear channels too).
@adamtoman5855
4 ай бұрын
I am installing a set of factory tweeters into a ford edge that do not have them from the factory. I have bought the crutchfield bass blockers. How close to the tweeter do the blockers need to be from the tweeter? Will the blockers block base from my speakers. I am planinning on tapping into the door speakers for sound to the tweeters.
@crutchfield
4 ай бұрын
They will install at the speaker locations. Just slide one of the Bass Blocker's connectors onto your Crutchfield speaker harness and the other Bass Blocker connector onto your speaker's positive terminal.
@Kelciesleftcheek
Жыл бұрын
I just installed 2 new 6x9 ds18 speakers into my front door panels and for the first five minutes they sounded great but them started to sound distorted at high volume did I blow them or do I not have enough power? I also have 2 12s in my trunk
@crutchfield
Жыл бұрын
We don't carry those speakers; but what is their RMS power rating and impedance? What are you using to power them?
@elgiro15
9 ай бұрын
if you connect the tweeter to a crossover do you still to have a filter in the tweeter?
@crutchfield
9 ай бұрын
If your tweeters came with an included crossover and that crossover is connected, you do not need to add an additional filter.
@joegardner4207
Жыл бұрын
Do you have any videos on how to wire in an ohm resistor and what resistors are best to use? Stock speakers are 8 ohm and I have infinity ref 3032, they are 4.
@crutchfield
Жыл бұрын
We do not have a video showing this process applied to resistors, but it does seem like it would be similar to this one.
@mycaddigo
Жыл бұрын
Does it matter Wich side of the capacitor I use on the speakers positive ??? Any end dosent matter ?!
@crutchfield
Жыл бұрын
As long as the capacitors in the bass blockers are not polarized, the bass blockers can be connected in either direction. And the good news is that the bass blockers we sell are not polarized! They can be found here: www.crutchfield.com/I-rYALc227/g_761/Bass-Blockers.html
@tylerbarton96
2 жыл бұрын
I am running 2 cvr 12 kickers wired down to a 1 ohm, in a q bomb pro box, I just installed 6.5 c5 kicker door speakers all around. How do I block the bass from going to the door speakers and only into the subs itself, do I need the capacitor shown in the video on each positive side of the speaker? Will it take away from anything of the door speakers when installed?
@crutchfield
2 жыл бұрын
Do you have an after market radio or amp you're using for power? If so, what is the power rating output per channel? Does the radio or amp have a built-in crossover or EQ?
@robertnorris6079
5 ай бұрын
Hey do i need to use bass blockers on Pyle horn phsp 6" 50watt 8 ohm when i hook them to my aftermarket radio thanks
@crutchfield
5 ай бұрын
The 8-ohm Pyle PA-style horn speakers are not designed for connection to an aftermarket radio that prefers to drive 4-ohm speakers on each channel. They have a 500Hz to 5 kHz frequency response so a band-pass filter would be required, a Bass Blocker would not be a good choice.
@thattox1cgamerxbox52
9 ай бұрын
Put these on my door speakers and now they don’t play any sound. Any clue what I did wrong?
@crutchfield
9 ай бұрын
It seems likely that either it is faulty bass blocker or perhaps the connections came undone. If you've double checked the connections and still hear nothing, you may want to speak with technical support. We include the toll free phone number to our technical support on the order invoice just in case their help is needed.
@xabre16v
2 жыл бұрын
Hi, question, I am using Pioneer TS-H1703 composet speakers in the front and Pioneer TS-1356II (coaxial) speakers in the back, all powered by the default factory radio. Now I want to add a subwoofer. What bassblocker do you recommend, I guess I need one bassblocker per speaker? And final question, the speakers themselves already have inline capacitors for their tweeters, can bassblockers 'stack' with them? (without negative outcome)
@crutchfield
2 жыл бұрын
You will need one bass blocker per speaker. We sell them in pairs. We didn't carry those speaker models but based on what we found online about them, the TS-H1703 should use these: www.crutchfield.com/I-rYALc227/p_007BB150/item.html and the TS-1356II match well to these bass blockers: www.crutchfield.com/I-rYALc227/p_007BB300/item.html
@vcastag
Жыл бұрын
Front and rear speakers in my new bronco are both 4inch. Should I get be using bass blockers on both? I will also replace 6.5 inch speakers below dash and do not plan to use them there
@crutchfield
Жыл бұрын
Hi Vincent, adding the bass blockers can be a plus in most cases with smaller speakers; but what are you using for power? Do you have any larger drivers or subs as part of this system?
@derekvarney5706
4 күн бұрын
I am using a kicker 200.4 and am wondering about what size blocker to use and if I should wire the speakers in series instead of parallel (8ohm vs 2 ohm) for the dash speakers. Using Crutchfield supplied adapters with 4” and 6.5” kicker ks speakers.
@Iadawmasikhasi
2 жыл бұрын
Which capasitor can remove the bass in 10inch speakers
@crutchfield
2 жыл бұрын
For subs, you'd want to use a crossover or even a DSP to make those settings. What is your exact sub/amp setup?
@ravenhawk29
2 жыл бұрын
Just upgraded the ram 1500 dash speakers to kicker DSC350 3.5's 2 ways . Which crutchfield inline bass blocker is recommended ??thanks
@crutchfield
2 жыл бұрын
These would cut the frequency off at 150 Hz: www.crutchfield.com/I-rYALc174/p_007BB150/Crutchfield-Bass-Blockers-150-Hz-cut-off.html
@AG4runner
2 жыл бұрын
Can butt connectors be used to substitute the soddering? What size if so
@crutchfield
2 жыл бұрын
You can use connectors instead. A 12- to 16-gauge speaker wire fit will work with our current models.
@deejay7218
2 жыл бұрын
Hey guys.i have a Gemini 15" pa speaker.i want to install a 4oms 200watts bullet tweeter but I want to block out the bass
@crutchfield
2 жыл бұрын
We have a dedicated Commercial Audio Group to help you choose the best PA system upgrades. Please reach out to them: www.crutchfield.com/I-rYTVc921/support/ContactUs.aspx
@Ghetto109
9 ай бұрын
What kind of Capacitor (ohm/ uF) would you need for each speaker?
@crutchfield
9 ай бұрын
This depends on many different variables specific to your own setup and speakers. If you want to check out all our available bass-blocker options for different frequencies check out the link below! www.crutchfield.com/I-rYALc166/shopsearch/bass_blockers.html
@1jordanx105
Жыл бұрын
do you have to solder them
@crutchfield
Жыл бұрын
In many cases, you can use connectors instead. Do you have a specific speaker in mind?
@salvadorperez9980
5 ай бұрын
I just use electrician tape
@jeffreybabb277
2 жыл бұрын
Should a bass blocker be installed on every speaker?
@crutchfield
2 жыл бұрын
That depends on the setup, What vehicle is this in and what gear will you have in the audio system?
@jeffreybabb277
2 жыл бұрын
@@crutchfield vehicle is 2022 Ford bronco, replacing all 4-4" speakers. System is not B/O.
@crutchfield
2 жыл бұрын
That size speaker is typically not good at producing bass. The best recommendation would be to use bass blockers on all the speakers and install a subwoofer system to produce the bass.
@jeffreybabb277
2 жыл бұрын
@@crutchfield thank you
@crutchfield
2 жыл бұрын
Glad we could help!
@diogo1988100
Жыл бұрын
Hi I am in UK just bought a new Rav4, I want to upgrade the dash speakers which I ordered JBL from the US, one side has dual speaker I understand one is for SOS. Is there any advice you could give on how to upgrade that speaker? I was thinking of removing the SOS speaker and moving it elsewhere, but not sure how to extend the cable. any advice would certainly help. I certainly will put in an inline capacitor as shown on your Video.
@crutchfield
Жыл бұрын
Congrats on your new vehicle! Is it a US specific model or UK?
@diogo1988100
Жыл бұрын
It's a UK model right hand drive.
@crutchfield
Жыл бұрын
Sorry, we won't have specs on the UK version. If you want to take some measurements though and reach back, we'll be glad to see what we can help you match up fit wise; but you'll want to double check on how that is wired in as well.
@diogo1988100
11 ай бұрын
Thank you very much I will work on it.
@crutchfield
11 ай бұрын
You're welcome.
@henrysmith3603
2 жыл бұрын
Can you add a Bass blocker to 6.5 mid range speakers
@crutchfield
2 жыл бұрын
Hi Henry, we'll be glad to see if we have a good match. What model speakers are you using? What are you using for power?
@henrysmith3603
2 жыл бұрын
@@crutchfield I have 6 6.5 mid 2pm.mm
@crutchfield
2 жыл бұрын
There is a chance that a midrange driver needs more audio blocked than a bass blocker can do. If that is the case with yours or if the amp will exceed 50 watts RMS going to the midrange driver, then bass blockers will not work. Were you able to identify the brand and model of the midrange driver you are referencing here? Also, which amp will be used to power them?
@utt2468
3 жыл бұрын
Thank you for the video. From where I can buy two capacitor bass blocker 270uf 50wv ? please let me know. Thanks
@crutchfield
2 жыл бұрын
The closest we can get is one that blocks at 150Hz with 4 ohm speakers: www.crutchfield.com/I-rYTVc227/p_007BB150/item.html
@utt2468
2 жыл бұрын
@@crutchfield Thank you for your response.
@utt2468
2 жыл бұрын
@Tom Smith Thank you very much, Tom.
@Prod.bysavage
Жыл бұрын
Can you use a base blocker on 6x9s?
@crutchfield
Жыл бұрын
Yes. What is your exact setup?
@robertnorris6079
5 ай бұрын
Hey i have a question i have 4 kicker 46CSC6934 6×9's in back deck, what the best hook up 2- 3 way passive crossover or just use bass blockers there hooked to aftermarket jvc kw-m56bt right now i will be hooking them to a 6 or 8 channel amplifier and i have 2- kicker 6 1/2 46css654 in each door and a 1"super tweeter can i use a 3 way passive crossover on each door or use bass blockers thanks for all the help do appreciate it
@rashmikadulith6294
Жыл бұрын
Hey guys please help me, I have 6 pioneer TS-G1620F speakers and two 1000W subwoofers on a bus. All of these connected to 400W pioneer amplifier. And I think i might need bass blockers can U help me which transistor should I buy?
@crutchfield
Жыл бұрын
We're happy to help. What are you using for power?
@rashmikadulith6294
Жыл бұрын
@@crutchfield 24v battery converter to 230V
@crutchfield
Жыл бұрын
Do you have the Pioneer speaker wired to a radio or an amplifier?
@rashmikadulith6294
Жыл бұрын
@@crutchfield wired to the radio
@crutchfield
Жыл бұрын
If you're using only the 6 4" speaker with your subs, 150Hz is your best bet: www.crutchfield.com/I-rYALc921/p_007BB150/item.html
@georgetheodosiou7850
3 жыл бұрын
Can i use bass blocker on a two way speaker with built in crossover (capacitor)? Thanks in advance!
@crutchfield
2 жыл бұрын
We will be happy to help. Which brand and model speaker are you referring to?
@georgetheodosiou7850
2 жыл бұрын
@@crutchfield Rockford fosgate prime R14X2. Thanks
@crutchfield
2 жыл бұрын
Yes, so a bass blocker will prevent the speaker from ever seeing those vfrequencies.
@georgetheodosiou7850
2 жыл бұрын
@@crutchfield Great! Thank you.
@bebomakram3059
2 жыл бұрын
What best bass blocker for pioneer 650 watt 9*6 it wiring in amp kenwood 500watt 4ch
@crutchfield
2 жыл бұрын
Hi Bebo, what are your amp and speaker models?
@bebomakram3059
2 жыл бұрын
Amp kenwood 500w 4ch Speakr ts-A6977
@crutchfield
2 жыл бұрын
Which model Kenwood 4 channel amp?
@bebomakram3059
2 жыл бұрын
Ps 647
@crutchfield
2 жыл бұрын
With that power which Kenwood lists as 40 watts RMS per channel and the speakers, you may not need to block the bass. However, you can test any time you want. It appears that amp has a filter that can be used to block bass from the speakers. You don't need a bass blocker as the amp already has a way to block it based on information we found on it.
@burjis24
3 ай бұрын
You should have zoomed in the camera especially when you were explaining how to connect wires to capacitor....video is taken from too far..makes it hard to see what you are showing
@crutchfield
3 ай бұрын
Is there something we can clarify for you regarding this installation?
@djtwiztid77
25 күн бұрын
If you don't know how to solder wires together for audio connections, please just take it to someone who can do it right.
@burjis24
25 күн бұрын
@@djtwiztid77 if whoever recorded this video does not know how to close zoom..they should learn
@quality_contentmydude6965
Жыл бұрын
this is a shot in the dark, but I installed two Infinity Reference REF-3032cfx speakers in my front dashboard of my 2007 chrysler 300 and I wasn't supplied with bass blockers from the manufacturer. would you know what bass blocker would work best with these speakers, so I no longer need to worry about distortion?
@crutchfield
Жыл бұрын
The Infinity Reference REF-3032cfx speakers should have come with two 270 microfarad capacitors that are enough to protect them it in any vehicle. We recommend installing them. If they are not available, then these blockers will also protect the Infinity speakers from playing frequencies they should not: www.crutchfield.com/I-rYALc227/p_007BB300/item.html If you use the ones listed below instead of that set above, then your speakers will be playing the frequencies it can play with the least amount of distortion possible: www.crutchfield.com/I-rYALc227/p_007BB600/item.html
@ThapandaYT
Жыл бұрын
Make sure to double check the styrofoam, the speakers came in that’s where I found mine!
Пікірлер: 100