This was the most beautiful front end rebuild imaginable. When you started it up at the end that was the finishing touch that made it seem so simple. Of course this is not simple but you did a fabulous job of making it about as simple as it could get. I do not know of a video on any other type of motor, chainsaw, small engine or otherwise where the entire operation of rebuild was done in one video to completion. All the cuiting and editing was just great. Thanks for a great video,
@nategardner1738
3 жыл бұрын
Talk about taxing on the price, HOLY SHIT!! $300 for 120cc jesus christ this is why i LOVE EBAY
@garyfisher4155
6 жыл бұрын
You omitted changing the main jet or lifting the needle inside the throttle slide to allow more fuel through, also you should have oiled the cam and housing, other than that v.good tutorial.
@maxmorrison2775
4 жыл бұрын
What size main jet should you use
@BikePackingPleb
3 жыл бұрын
Skipped over gapping the rings properly too if you follow this tutorial you'll probably blow your scooter up
@KhrissZaitsev
2 жыл бұрын
Does the weight or mass of the new piston remain the same as the one from lower CC? I wonder about that since I would believe any changes in that would require a new Counterweight as well. Or, how does that work? maybe a new video addresing that for those who are curious about it?
@autotechmike
4 жыл бұрын
Does this use 64mm or 69mm valves
@chadman2275
6 жыл бұрын
A secret I figured out pull the chain mark the very center of chain with sharpie then mark cam with sharpie perfect timing every time
@emil55555555
5 жыл бұрын
but it can slip at the bottom.
@wilconradnorinradd
Жыл бұрын
I think when I swapped 139qmb heads, I installed the cam NOT @tdc. OR... the $40 donor 139qmb has different valve length as I hear tapping n clicking @ low speeds n idle. OR.. it's the lack of a proper head/exhaust gasket. I'll update in a couple days,.. BIG UP RWD!! from Kapolei, HI🤙🏾
@jamesgray3394
Жыл бұрын
I'm going to have to watch that again once I have the parts
@SegaDisneyUniverse
3 жыл бұрын
After watching this tutorial I feel a lot more confident that I could do this myself. But my clumsy behind would probably end up breaking something anyway lol!
@thomasrobertsfavesbestofco7069
2 жыл бұрын
A bit of confidence and determination in yourself works. I've been scooting for over 10 years and this is the first scooter that I've been doing my own work on. It's pretty simple as long as you do what is shown in the videos on KZitem 👍
@thomasrobertsfavesbestofco7069
2 жыл бұрын
Just remember to take your time and don't get in a hurry ☺️
@thabrownieviking
6 жыл бұрын
Do you leave the EGR port open?
@DomVito87
2 жыл бұрын
I did that with my gy6 . Went from 50cc to a 80cc . Huge difference. Cvt tuning, jetting , exhaust made a huge difference. Can reach speeds up to 50. Which is nice for my backroads that require 40mph
@betavirus11
2 жыл бұрын
did you end up switching out the carb or did you just change the jets? thanks.
@DomVito87
2 жыл бұрын
@@betavirus11 just the jets
@betavirus11
2 жыл бұрын
@@DomVito87 thanks for the reply.
@DomVito87
2 жыл бұрын
@@betavirus11 no problem buddy! Good luck!
@aaltjanbuijtenhuis4578
2 жыл бұрын
Wich Jet did you get?
@Nickroberts8
6 жыл бұрын
Do you guys do installations of big bore kits? I live in Denver and have a scooter, I'd like to install a kit in, but I don't trust myself enough to take it apart and install myself. Thanks!
@0643wes
6 жыл бұрын
I've done this kit on a kymco agility 50 when it had about 3000KM it worked great now I have 11000KM on it and I can barley get it started it's almost like it has to much compression cause when the piston makes a revelution it sticks if anyone has any pointers let me know
@T.B620
5 жыл бұрын
Check valve,s and change oil every 5000 km also check timing belt
@fitzwater504
2 жыл бұрын
On the higher compression piston, barely push down tell you get passed the high compression. Then try kicking it started. Should start a lot easier. If, this is when using electric start only or mostly. Yes, I’d try adjustments on valves. Forsure
@paulchristiansen7014
3 жыл бұрын
thought you only did HONDA RUCKIS swaps...sweet...
@MrGuitarguyadam
6 жыл бұрын
How does this big bore kit compare to the 100cc kit from J&J Power Sports?
@joncline1033
Жыл бұрын
Can you recomend the parts needed to upgrade the stator and other electrical components on a kymco agility 50 scooter?
@jesserichardson9280
Жыл бұрын
Just bought and was installing the kit and realized I have lost the Circlips, anyone know the size and dimensions of these Circlips?
@alfredbosire7677
Жыл бұрын
I need tools like digital torque wrench, impact tool, all sorts of socket box spanners, Latchets, Tee spanners, just mention afew. Thanks.
@dalewoods7308
6 жыл бұрын
After every thing done and finish what kind of horsepower is it putting out
@paco_rider
3 жыл бұрын
3 from stock and maybe 5 with this? Don't know
@iamjeromeflores611
Жыл бұрын
Where should i buy an bbk for my 50cc scooter? Its 2022 baodiao 50s3? Thanks
@jarencreations7003
3 ай бұрын
Don’t go 11foot pounds go like 9 because I broke mine off before it could even reach 11
@backyardmec2348
5 жыл бұрын
I run 150cc carbs on 50mm snm bigbore kits and i also ran into a problem trying to install one on a long case eton 4 stroke engine ill get the case number tmrw but ik its not qmb but it is a gy6 50cc engine but im now in the process of boring the case ill let you know what happens after i install the bigbore kit nd would the belt being squished nd used cause an engine to not pass 35 mph?
@LonnieMinton-u1k
Жыл бұрын
The thing around your clutch I see them changhing four plugesand they put four bots in it and puu
@jeffkrauss5582
3 жыл бұрын
Whats the actual size of the piston
@jouman450
Жыл бұрын
47mm for 71cc, which they call "80cc", and 50mm for 80cc, which they call "90cc".
@dapv144
3 жыл бұрын
You should have a follow through on the engine break in after bbk.
@r33lgaming76
6 жыл бұрын
Thanks. Found it very usefull and it helped me to do my scooter faster and properly in 2 hours. Many thanks for this video.
@GY6-SCOOTERS
2 жыл бұрын
Great tutorial video matt ...🙂👍I'm currently working on my 50cc thinking about upgrading her to a 80cc
@RollingWrench
2 жыл бұрын
Thanks dude! Do itttt!
@wildlifenowife9886
2 жыл бұрын
I've been looking at upgrading my 50cc been looking at a big bore kit for it
@crabjoe
4 жыл бұрын
Wait.. Did I hear you say the black ring goes on the top of the piston? Unless it's marked, I've always seen the silver ring on top and the black as the ring under it.
@dentalflesh677
3 жыл бұрын
Hey watch this guy he goes really in depth with putting the rings on kzitem.info/news/bejne/kWN9toyYhmmihYo
@sethaustin5086
Ай бұрын
Exhaust was 05 right? You didn’t say anything
@dubrpanda1636
Жыл бұрын
Some qmb139 will require case boring... some 80cc -100cc big bore kits have the thicker cylinder walls that wont fit into the 50cc cases
@RollingWrench
Жыл бұрын
True, but all of our cylinder kits drop in
@knoxbom3274
3 жыл бұрын
What size carb do you recommend with a BBK
@Pau11984
Жыл бұрын
I have a 2022 bd50qt-2a let me tell u it does 50mph stock on my gps I got it to 57mph .... I want to do a big bore but stock the reliability is perfect ..... I know a BBK can push my speed and acceleration to better heights but I don't wanna loose the reliability factor only 10w40 valvoline full synthetic since day 1 ........I actually used the oil that came in scooter for a few hundred miles then went full synthetic
@RollingWrench
Жыл бұрын
Anytime you increase performance you will loose reliability unfortunately
@larrykeesee1442
6 жыл бұрын
We need a video on a better headlight for scooters
@howardlangford8087
4 жыл бұрын
Led
@anonymoose6873
4 жыл бұрын
I bought an 8 dollar 6 inch LED light bar on ebay and spliced it in with the main headlight, then mounted it on the front and I went from barely seeing at night to seeing everything bro
@MotoMiles
4 жыл бұрын
@@anonymoose6873 hmmm i am thinking about doing something similar..
@anonymoose6873
4 жыл бұрын
@@MotoMiles for $13 on Amazon you can get the niilight 4 inch led lights there's 2 of them but now I'm running just one and the option of having a power switch is pretty darn satisfying
@MotoMiles
4 жыл бұрын
@@anonymoose6873 awesome thank you brother !!!!
@fixingproblems3183
3 жыл бұрын
I have install the big bore kit on my 139QMB scooter. It runs great, but when my kid and I get on the scooter the pushes the rear main seal out and all of the oil leaks out. We are both total of 320 pounds. Does the back pressure increases because its too much weight for the motor to handle or do you think it’s some other issue when the big bore kit?
@amatureskater15
3 жыл бұрын
Does it do it when you ride single? if not... you have your answer
@alexnather7614
Жыл бұрын
Im using this video to help repair my 150 i ran it without an air filter and a small rock entered the air intake and destroyed the top end... I have done a BBK kit on a 50 before and im confident i can fix my 150. Now i know to ALWAYS use an air filter 😎😎😎🤙
@yaroslavchagovetz872
Жыл бұрын
I cannot stop wondering why people neglect obvious things
@apegg5203
2 жыл бұрын
I have that same scooter but it is 150cc year 2021, it is compatible with all the gy6 parts? I want to put the new clutch and the 180cc kit..! Plz respond
@apegg5203
2 жыл бұрын
Kymco súper 8 150cc 2021 Parts I want to buy -Reveno clutch -180cc kit And head -gy6 variator Is it compactable?
@lukeschuckenbrock5370
5 жыл бұрын
My Nilla Wafers always get soggy in the bottom of my banana pudding. Any ideas?
@RollingWrench
5 жыл бұрын
I have a whole series on that exact subject. Lol
@aydinmerken
6 жыл бұрын
Is that fit peugeot kisbee 50cc 139 qmb-e
@sethaustin5086
Ай бұрын
What did you use to scrape the old gasket off?
@karirautio
11 ай бұрын
You have the special tool for valve adjustment. Feeler gauge is not needed. There is the scale, 1 turn divided by 12. The pitch of the screw is 0,5 mm. You turn the screw first to 0 clearance and then open as mush needed. 1/12 x 0,5 mm = 0,042 mm, 2/12 x 0,5 mm=0,083mm and 2,5/12x0,5mm=0,1mm. If you watch KZitem Nicks Garage, he never use feeler gauge when adjusting valves in V8 motors. He opens the adjusting screw from 0 clearance half turn. Very easy method.
@JA-fn7le
2 жыл бұрын
What is the success/fail rate of the stock QMB139 crankshafts with the 90 vs the 80cc BBK's? I think I'll go 80cc since I want the engine to last, I may go all the way and install a Naraku heavy duty crankshaft and upgrade oil pump.
@grazz7865
Жыл бұрын
I heard 80cc is as high as you can go before you need to change a whole bunch of other stuff. There is no oil pump (at least on mine). It’s described as “splash “. As the crankshaft turns, it splashed the eral over everything
@anthonytoler3916
10 ай бұрын
From what i was told at a Bintelli dealer was the Naraku heavy duty crank and the 100cc BBC hold up as good as a 50cc when paired together. he said he has built alot of them.
@pandanda656
Жыл бұрын
So I have a Kymco Like 2 50i with injector and it is painfully slow it barely gets to 27 mph. I was thinking of installing big bore kit, however I am not sure if it would make any difference, due to the injector not supplying enough fuel? Also does the rpms of the engine need to be increased in order for that to work? Currently my max rpms are at 7000. I changed variator weights, opened the rear wheel gearing and it all seems as if its not restricted. However when I drive it the top speed is all the same. I had a bump in top speed to 33 mph when I installed new belt however that was just for 1 ride and then it fell back as previous. I am desperate in making it at least go 35. I am thinking the variator plate could be undersized as when I measured it, the diameter was about 70-80mm I don't exactly remember. I saw a video of a chinese ecu pushing the engine to 10k rpm, however it is incredibly overpriced. The gear ratio of the rear wheel is secondary 12/55 and primary 12/50 with 12 inch tires and the engine is I believe longcase. I am thinking of ordering malossi 2000 variator, because variator must be the only thing restricting that scooter. I would appreciate some input. I also considered reflashing the ECU to bump the rpms because there is no cdi box, however that would be very expensive and needs to be done by motorcycle ecu mapper
@marineboy4181
3 жыл бұрын
Oh my god do anyone knows the right rocker arms for this 90cc Big Bore Kit.? I keep getting them wrong LOL please message me back
@RollingWrench
3 жыл бұрын
64mm
@marineboy4181
3 жыл бұрын
@@RollingWrench and yeah alright thank you bro. 💯👍🏽
@fitzwater504
2 жыл бұрын
@@RollingWrench What about the 69mm is this something newer. Then when this video was made???
@jamesgray3394
Жыл бұрын
That's another thing I have no tools they even start with
@rickvankorven107
7 ай бұрын
nice video! did a 90 cc measly kit on my gy6 retro grande ;-) but what mm carb do you recommend? it is a 18.5mm right now
@xxxkingsize69kingsize40
6 жыл бұрын
A 150 with mods will dust a 100 take of top end mid range all around any thing under 125 just ain't worth it 150 is already to slow bore that 150 to at least 180 with mods
@forevercomputing
6 жыл бұрын
CVT/transmission upgrades?
@nedthomas3000
3 жыл бұрын
I have a 2018 SYM symply 50 I don't think this kit of compatible but does anyone know what kits / upgrades I can do to my bike o can't find any myself
@raymondgraham7559
2 жыл бұрын
Thanks for video. I want to follow you to help install the monster 90cc big bore kit and camshaft in my 2021 linhai joc 49cc scooter. Will this kit work in this scooter? Thank you!
@celticknyt
Жыл бұрын
Why are you selling a 72cc big bore kit (47mm) and calling it an 80cc?
@RollingWrench
Жыл бұрын
Because everyone else calls a 50mm a 100cc. So we just run with it. Just like we call our 52mm kits 120cc kits. And just like Yamaha calls their 580cc kits a 600cc
@howardlangford8087
4 жыл бұрын
Will putting a 100cc big bore kit on a 50cc , cause any long term damage to the crankshaft? And should I put on a higher volume oil pump as well?
@shab036
3 жыл бұрын
yes you will need to upgrade ur crankshaft
@JA-fn7le
2 жыл бұрын
This is why most scooter techs recommend for daily commuter scoots to stay 80cc if you are going to stay stock crank wise.
@gfbentertainment9566
Жыл бұрын
do i need to change my crankshaft and rod to put a big bore on my gilera runner 50cc?
@fitzwater504
2 жыл бұрын
When will you have this kit available again, It’s saying sold out. I would like the 90cc big bore kit & the crankshaft to for this unit the whole set-up. Also is this the 64mm or 69mm valves? I’d like 69mm please! Thanks P.s. I’m need a bigger carb to soon!!
@davidduffy2046
5 жыл бұрын
With all these mods, isn't the exhaust now restrictive? Did you rejet carb?
@RollingWrench
5 жыл бұрын
Exhaust upgrade would be the next step, without it it’s still great. We are a mile above sea level here in Denver Colorado, the carburetor is fat out of the box. Once the big bore has been installed the jetting is perfect. So no rejet, however for most people yes.
@colonelqb5
3 жыл бұрын
What do you suggest the jets be increased to? I installed the 80cc bbk on my agility 50. Also installed pod filter and deleted air box. Having tough time getting over 30 mph. I’ve tried 90 and 92 on main jet.
@fitzwater504
2 жыл бұрын
@@colonelqb5 It’s different in different areas. Higher elevation vs. low elevation. Air is thinner up high, vice versus. So, each tune is & will always be slightly different a bit.
@ericstephenson3165
3 ай бұрын
What happens if you get the two rings switched the one video the black was in the middle and this one is black on top do i need to tear apart
@ericstephenson3165
3 ай бұрын
I'm in the middle of doing this , if some know if it's no big deal and i can continue without worrying
@AlvaroSanchezChile
5 жыл бұрын
Hi, you Comment that this fits the Agility from Kymco. Just for info: I have an 125 Agility from 2018 12 inch wheels and air cooled. Do tope end of the KN25SR engine on this scooter is compatible with GY6 or similar qmb139 Chinese generic engines? Do a Cilinder kit can be fitted? Thanks in advance
@Gkgarage13
3 жыл бұрын
Great video man but I noticed that the piston is upside down. The arrow in the piston always shows the intake side. That's why it has larger gap for the valve move towards the piston.
@RollingWrench
3 жыл бұрын
If it was backwards we would have big issues. The valve would hit the pistons
@sandy1234853
2 жыл бұрын
Their is an arrow pointing down but in this case it must be the direction on flow therefore its pointing towards the exhaust and also next to the arrow it says in next to the top valve groove so it was deffinently in correctly
@mikeybtweekn5001
2 жыл бұрын
What tools do I need to change the crank shaft
@JA-fn7le
2 жыл бұрын
Why not have the pair studs for California, then you could install the pair tube and the green na*is wouldn't be any the wiser. 😉
@thorfirebaugh4659
3 жыл бұрын
Will you please do a 50cc to 150cc swap on a Dong Fang 50cc SXR I have a pic if you can't find one by name I cant find anything on them and I wanna do a swap sooo bad
@wademinton8952
11 ай бұрын
How many mm is the piston on this kit
@oldschoolmotorsports9990
6 жыл бұрын
What size carbs and jets are you guys going with with these 100 cc swaps?
@fatcunt7091
5 жыл бұрын
What’s that special tool called?
@user-iw4jc7ss9r
2 жыл бұрын
I’m curious I’ve seen a few other videos and they said chrome piston ring up top but here you have black up top top does it differ from kits or is someone wrong
@ryankariem2306
2 жыл бұрын
Does this fit on a peugeot kisbee 50cc 139gmb-e 4T carb?
@jameslouis440
3 жыл бұрын
Ever since I put a 80cc big bore kit in it started over the summer for about 10 mins and hasn’t started again since I’m about to give up its been sitting and sitting and I cant get this dog damn thing going
@jestAdad812
Жыл бұрын
What size piston and valves are with this kit? I cant find the details anywhere...
@matthewternes8388
5 жыл бұрын
Does my Kymco super 8 4t 50cc (2018) have the same engine as the agility ?
@RollingWrench
5 жыл бұрын
Yes
@jamessaylor9012
Жыл бұрын
Are there still advantages with this on stock 50cc my son races 4 wheelers and can not bore thank you
@hazz6386
Жыл бұрын
It turns on but the wheel dosnt spin anymore the engine only revs
@RollingWrench
Жыл бұрын
Belt is probably broke
@yaroslavchagovetz872
Жыл бұрын
Why dont`t you detach the whole engine from the scooter itself? Replacing cylinder on mounted engine is a bit harder
@RollingWrench
Жыл бұрын
You can do that to. For me it’s unnecessary extra work.
@yaroslavchagovetz872
Жыл бұрын
@@RollingWrench We did a lot of unnesessary extra work without detaching the engine from my Kymco Agility 2008 16" wheels yesterday. In the process it turned out that you cannot remove cylinder head if you dont detach the engine. Also - installing piston is much more easier when you got your engine removed from frame
@manuelvalencia4012
5 жыл бұрын
Hi there ! It's possible to cut the case of my gy6 150cc short case ? For a bobber proyect with 16 inch wheels ??...Have a great day amigo!!
@rakamlih
Жыл бұрын
Nice and good work Super job 50 cc beter economische now en relaxing
@s.f.morris7331
Жыл бұрын
$375 to maybe make your scooter go 5 to 10 miles faster? yikes my jonway 49cc on a flat open throttle run went past the top speed on speedometer. all I did was remove emissions system. think I hit almost 55 mph. looked down at how fast I was going and flipped out. and thought wait these little wheels arent meant to go this fast for too long. then slowed it down. but now have a bore kit someone gave me and wondering if I should even put it in.
@RollingWrench
Жыл бұрын
A big bore isn’t for a higher top speed, it’s for more muscle. Faster acceleration. Remember you aren’t changing the gearing only the power.
@s.f.morris7331
Жыл бұрын
@@RollingWrench well ok I didnt think of it that way. I have a brand new bore kit ive never installed. for one it kinda intimidates me and for two it kinda intimidates me. thanks for your reply. how would you go about getting a stripped bolt off the fly wheel. my impact wrench I guess wasn't strong enough or someone super glued it or I tried to take it off in the wrong direction. but its stripped as hell and I have no idea how to get to the stator now. ive tried lubricant spray. I have the special tool needed but cant even get to that step because of this damn bolt. any suggestions from you or anyone else that sees this post?
@grazz7865
Жыл бұрын
@@RollingWrench exactly. You might get a little more speed out of it (not much) you’ll get there must faster. Not so much of a struggle.
@johndefalque5061
Жыл бұрын
Just what is that valve adjustment tool called? Not seen one before.
@Destraight
5 жыл бұрын
its hard trying to line up that timing. I ran out of daylight
@jonathanolmos3841
2 жыл бұрын
I want to upgrade my engine can you send me the link so I can purchase
@nb2481
3 жыл бұрын
I have a DF50SST and mine says qma139. Is it compatible? And what size carburetor would you recommend.? Even a jets size recommendation would be helpful. Thanks in advance
@RollingWrench
3 жыл бұрын
Yes, it will work. I use this carburetor, jetting is always different :www.rollingwrenchdenver.com/products/gy6-125cc-150cc-carburetor
@Smodlee
2 жыл бұрын
Is this kit available for a 2022 vitacci Denali 50?
@blackgumbo5536
6 жыл бұрын
Thank you for illustration a good how to video. I installed my big bore kit one shot no hiccups. Thank you. Please explain about installing a tachometer and correct reading for a big bore kit. Thanks again.
@kirtlavine2918
4 жыл бұрын
Check out wera tools from Germany. You look like a guy that likes the best.
@maggie4475
3 жыл бұрын
This video was so helpful and if I had the tools I would do my own scooter with the 80cc Big Bore Kit... Thank you so much..
@nicholascorbett6655
4 жыл бұрын
Mr wrench sir 🔧.. I have about 100$ to spend as of right now. Should I purchase a kit that comes with 100cc big bore and all gaskets , exhaust, racing cdi, new rollers and exhaust and ignition coil. Or for same price get an 80cc that comes with a new carburetor and cdi with fancy 3 prong spark plug? I have a 2019 tao tao pony that has 1000km. But also have a brand new in the box stock motor I intend to install bb on. Also brand new stock carb.. I live in a very hilly area I basically want best power and speed for hills. Reliability being most important. Thanks to anyone who can help. 😁🛵👍💪
@RollingWrench
4 жыл бұрын
None of the above. It sounds like a amazon or eBay purchase. Remember, you pay for what you get. Save your money for this kit: www.rollingwrenchdenver.com/products/90cc-monster-big-bore-cylinder-kit
@devinlemay4297
3 жыл бұрын
Can I put a 50mm head on a stock cylinder? Or do I have to get a new cylinder too? My bike is a Tao Tao atm 50
@stevesemelbauer241
6 жыл бұрын
With this big bore wouldn't you need more fuel
@RollingWrench
6 жыл бұрын
Normally yes, but because we are a mile above sea level the stock jetting makes the scoot run rich up here (Denver Colorado). Do a big bore and its pretty close to perfect jetting :-)
@joeleeman9886
6 жыл бұрын
Ahh yet another "perk" to living in CO these days. Cant wait to blaze my way to CO!!!!!
@s.f.morris7331
Жыл бұрын
both of the exhaust valves were at .004? I thought top one was .003 and bottom was .004. does that matter? should I change mine?
@grazz7865
Жыл бұрын
.001 variance should not make that much of a difference. At best, you’ll get some tapping noise
@KikoBach94
3 жыл бұрын
00.4 intake and 00.4 for exhaust ???
@cameronmochizuki1784
6 жыл бұрын
Nice but I installed a 150cc short case in my kymco agility only issues I have is stock rear rim don't fit replaced it with a 150cc rim with stock tire now tire rubs on inside left side of case and shock any info on fixing that .thank u
@TheVegasbud
6 жыл бұрын
12 " agality or what model ? I was a kymco dealer in Vegas for 15 years
@cameronmochizuki1784
6 жыл бұрын
Chris i have a 2015 agility 50 4t
@MetroLinerXLZ
6 жыл бұрын
Short case GY6 150's can't accomodate a 12" wheel. The long case easily accomodates bigger wheels. The Agility can accomodate a long case GY6 150, just need a longer shock to prevent tire rub on the rear mud guard (or you can remove the mud guard and eliminate that problem).
@MetroLinerXLZ
6 жыл бұрын
I currently have a Kymco Agility 125. I did a GY6 swap at 40K, still going strong 10K later (just had to replace old parts along the way). Did you swap the stator from the old Kymco motor as well?
@cameronmochizuki1784
6 жыл бұрын
MetroLinerXLZ awsome
@oguzdag6
5 жыл бұрын
hi, peugeot kisbee 2018 50cc enjection 139qmbj engine code. Is it compatible?
@gordoflaco3959
2 жыл бұрын
can I use the stock rocker arms assembly on 100cc big bore kit or do I have to get a new one ?
@user-neo71665
6 жыл бұрын
those 3 tiny pistons are cute
@armdrop101
Жыл бұрын
What jetting for 50mm bbkc??
@RollingWrench
Жыл бұрын
It’s never the same
@armdrop101
Жыл бұрын
@@RollingWrench assuming 85 to 95 in that range for jetting
@gameribanez9796
Жыл бұрын
Followed your tutorial but I am hearing a quiet scrape or noise when turning crank by hand exhaust and intake are off spark plug is in. Is this normal? It turns over and only has resistance where it needs to
@RollingWrench
Жыл бұрын
Be sure the spark plug is out when you turn it over. If it still scraps pull it back apart to see what the issue is
@gameribanez9796
Жыл бұрын
@RollingWrench thanks she runs fine so far. I have a question I put a 96 main jet in and have a pod filter on it how do I know if I'm running lean I get a pop on deacceleration but I drilled holes in the rear of stock exhaust to provide more flow it was popping before bbk is a 96 big enough
@RollingWrench
Жыл бұрын
@@gameribanez9796 to know for sure get a wide band: www.rollingwrenchdenver.com/products/wide-band-o2-sensor-tuning-kit?_pos=1&_sid=24c770cfa&_ss=r
@gameribanez9796
Жыл бұрын
@RollingWrench question I took it out for a ride the second it hit 40 it started buzzing and beeping at me I thought it was my music at first but when I let off throttle it went away
@gameribanez9796
Жыл бұрын
@RollingWrench is there some sort of warning horn?
@aaron71
6 жыл бұрын
...$375? You kidding? Can get the same parts on amazon/ebay for less than 1/3 that!
@RollingWrench
6 жыл бұрын
Dude, you may learn the hard way. You get what you pay for. We only sell the good stuff. If you want amazon\ebay quality I’ll sell it to you. I’m not a big fan of returns.
@aaron71
6 жыл бұрын
The stuff you guys sell is the same stuff that comes out of China on Amazon. There's no name brand when it comes to China scooter parts.
@CB-425
Жыл бұрын
Thanks just got 80 cylinder installed no issues
@Smodlee
2 жыл бұрын
My engine isn’t positioned up that high the cylinder is down more so when I do this big bore kit I’m hoping I don’t have to remove the engine off the bike
@grazz7865
Жыл бұрын
Look at it this way. It will be WAY easier to work on out of the bike. That’s what I did
@BigEpinstriping
4 жыл бұрын
I have a Kymco Agility 50, do you need to bore the case for the cylinder jug to fit properly when you go this big?
@RollingWrench
4 жыл бұрын
This kit is a drop in kit. No boring needed
@allenroelfs9975
3 жыл бұрын
What about a 6xy139qmb
@Jason_Wheeler
2 жыл бұрын
Awesome
@trumpsarmy2499
5 жыл бұрын
I'm ordering this kit with the new cam my kymco 50 agility I'm excited to do this I never done one before so learning on the fly lol
@RollingWrench
5 жыл бұрын
It’s rewarding and not to difficult.
@trumpsarmy2499
5 жыл бұрын
I see you sell a video on a step by step on how to do it, I think that will be a good investment too
@trumpsarmy2499
5 жыл бұрын
These are the numbers I found down by the kickstand kg1osa and underneath that is *2215982* on my kymco 50cc agility scooter, what motor do I have and will your "90cc" kit fit it??
@lboogiesmith483
3 жыл бұрын
Can I do this to my kymco people 50 2T or is there a specific kit for me??
@idcemail123
3 жыл бұрын
My valve cover cracked after tightening it over the engine studs, The right side of the bike studs stick out more from the rock arm assembly.
Пікірлер: 325