I've done this many times and I've had to deal with some tough spaces and crappy bilge access but I've never seen one as hard to work in as your boat. I give you massive props for getting in there and being able to get that done man. What a tough job
@SmokinReels
3 жыл бұрын
If it wasn't for the camera I would still be trying to figure that one out, my arm was stretched to my shoulder down the access hole so there was no way to see what I was doing. Thanks
@joematthews8221
Жыл бұрын
I think mines worse
@michaeltrost2150
3 жыл бұрын
Very impressive job, I thought my bilge was tough. Great video.
@SmokinReels
3 жыл бұрын
Thanks 👍
@scottvanachte893
3 ай бұрын
Whenever I make a butt connection, I use marine heat shrink connectors (as you have) but then I also put a separate larger piece of self sealing marine heat shrink over top of the entire thing for that extra layer. So far no issues :)
@apope2311
2 жыл бұрын
Thanks for the help just inherited an old sailboat.. had zero clue.
@SmokinReels
2 жыл бұрын
Good luck with your project, you might want to check out Boatworks Today as well, he has some great videos and loves sailboats.
@trevorwhat
2 жыл бұрын
Big thanks for the walkthrough. Very helpful.
@SmokinReels
2 жыл бұрын
Glad you enjoyed it!
@user-od9pj3vq8y
3 жыл бұрын
Great video!
@SmokinReels
3 жыл бұрын
Thanks!
@ianp7799
Жыл бұрын
God I admire you
@bxbmbr766
Жыл бұрын
New subscriber great content
@isabelwallace703
22 күн бұрын
👍
@haydenloader4529
2 жыл бұрын
At the 12:56 mark, what is the role of the hole in the hull in the top left of the screen?
@SmokinReels
2 жыл бұрын
That is the Portside drain.
@kevingastle5442
2 жыл бұрын
Where did you get the PVC connector that is attached to the bilge pump.
@SmokinReels
2 жыл бұрын
That came with the pump.
@grimyjersey6499
8 ай бұрын
Why not fill the old holes with epoxy?
@SmokinReels
Ай бұрын
We can’t gel coat over export do we stay away from it.
@Boteris
Жыл бұрын
No test video?
@SmokinReels
Жыл бұрын
It will be coming up as well as the console wiring, once we get back on this project. Make sure you subscribe so you can see it. Thanks
@robertcomer1162
2 жыл бұрын
Not at this time.
@BrogeKilrain
2 жыл бұрын
Why u not use automatic pump ?
@SmokinReels
2 жыл бұрын
The foot switch will run the pump automatically. If that switch fails(which they do) we can swap it out without replacing the whole pump. We will also have a manual switch on the dash. That will be coming soon so stay tuned. Thanks for watching.
@BrogeKilrain
2 жыл бұрын
@@SmokinReels most those pumps made by same factory $15-$20
@yositlsilva5101
2 жыл бұрын
all I wanted to see was the wiring... and you skip it :-(
@SmokinReels
Жыл бұрын
The control wiring will be coming up when we wire the console. Sorry about that I’ll have to make a new video when the job is complete. Thanks for watching
Пікірлер: 29