Kinda had my doubts when i saw the croqs, but i guess you do know what you are doing. Excellent video. Get some boots.
@tj612
Жыл бұрын
Great video! Thank you. Gonna DIY my well pump next month.
@MooneysExcavating
10 ай бұрын
No problem!
@kylem6532
Жыл бұрын
This is awesome! Thanks for taking the time to share your knowledge!
@MooneysExcavating
10 ай бұрын
No problem 👍
@bcrowe3483
Жыл бұрын
Good video man! I know you’ll get them down to perfection!!
@joshuaperry4103
5 ай бұрын
Excellent video. Thank you!
@biff2k2
3 ай бұрын
Put a t wider than the casing at the end of your gas pipe so it can’t fall into the well.
@tomcio1978
11 ай бұрын
Great video. Wish you would have listed the part numbers on the pipe connectors and other stuff you used
@KeithJohn-qd6pr
6 ай бұрын
Up where I am the casing is steel . Little tougher to drill I like the idea of sleeving the pump wire I've had wires chafe and break I'm sure you did it but smearing some silicone grease on that adapter and o rig is a good idea
@MooneysExcavating
6 ай бұрын
Thankyou, I stared sleeving the wires for the same exact reason.
@mee-jn3vl
2 ай бұрын
Great video, could you tell me what HP pump you guys used. thanks
@dannyboy163
8 күн бұрын
kind of a dumb question, but howd you get the electrical tape off the pitless adapter? just yanked it off?
@MooneysExcavating
8 күн бұрын
@@dannyboy163 yessir!
@genevelis6075
3 ай бұрын
I like the idea to put 1" Polypropylene Conduit to protect The Wire. I wonder why you did not keep the conduit all the way to the top? Also, there is 1-1/4" CTS 250 PSI Poly Pipe available - why not to use it? It will not reduce the diameter from the pump and can withstand more pressure.
@MooneysExcavating
3 ай бұрын
We have codes. Have to follow them.
@genevelis6075
3 ай бұрын
@@MooneysExcavatingYour codes prohibit to put 1 1/4", 250 psi pipe instead of 1", 200 psi poly pipe?
@MooneysExcavating
3 ай бұрын
@@genevelis6075 yes
@fakename9024
10 ай бұрын
I noticed that you used Hose Clamps. Are Pinch Clamps a bad idea?
@MooneysExcavating
10 ай бұрын
I just rather hose clamps where you can really tighten them. This line has constant pressure.
@karlfox9369
9 ай бұрын
Hi Great video! do you think the pitless adapter will work on an above ground jet pump or would it suck air?
@MooneysExcavating
6 ай бұрын
I am not sure honestly. We only use them for submerged pumps.
@rogermahler9686
2 ай бұрын
Many Municipalities require the well head to be 18" above grade to prevent surface water contamination (from rain and flooding) cutting below grade is a no no.
@MooneysExcavating
Ай бұрын
Makes sense. This was in the middle of a field and did what the owner requested.
@anthonyzarcone8696
Ай бұрын
Good video you need a check valve at the pump
@MooneysExcavating
Ай бұрын
Thankyou. Pump has a built in check valve.
@anthonyzarcone8696
Ай бұрын
@@MooneysExcavating I understand that theres a ton of head pressure cause of the depth
Пікірлер: 27