Just a suggestion when using a hole saw with a pilot: go halfway through from the front, then come from the backside to finish. Besides limiting the friction drag from a deep saw, it prevents a splintering breakout when you make it to the far side.
@ExtremeDIYGuy
3 жыл бұрын
Yeah that's good advice, thanks for sharing!
@Whalermansteve84
3 жыл бұрын
Nice job brother. I’m still in a standstill with my whaler. Hoping to get done by winter
@ExtremeDIYGuy
3 жыл бұрын
Thanks! I can sympathize, This was my 6 month project and took almost two years to get done! Good luck, get her finished!
@sportsman48
3 жыл бұрын
Running my teleflex today and honked it up by measuring long with the center console 13 footer and ordered a 13 foot cable. Here's hoping it doesn't look like a hot mess
@okiefisherman1480
2 жыл бұрын
Great video. Very informative. Also like the labeling to find each part of the installation process. Thanks for posting this.
@ExtremeDIYGuy
2 жыл бұрын
Glad it was helpful!
@robertsmart5600
2 жыл бұрын
Brilliant, this was all they had at my local boat store just before Xmas 21 so I bought it. Nice video of attaching QC cable and pins. Store gave me wrong steering wheel nut & key, looks like it is half inch fine thread? Local hardware store only has coarse thread nuts.
@johnsalles8248
2 жыл бұрын
Thanks Joe
@ExtremeDIYGuy
2 жыл бұрын
Your welcome
@Judge_Judy
3 жыл бұрын
very helpful ...doing some maintenance on mine ...mite pop it out and regrease
@ExtremeDIYGuy
3 жыл бұрын
Glad it helped
@delasol73
3 жыл бұрын
Nice! thanks for posting. About to do this same job and it helps to see it first.
@ExtremeDIYGuy
3 жыл бұрын
Glad it helped
@faronmastin5788
3 жыл бұрын
Thanks for the video it will help me install mine right.
@ExtremeDIYGuy
3 жыл бұрын
Your welcome!
@bouldernelsonbigfoot
2 жыл бұрын
THX Guys.
@ExtremeDIYGuy
2 жыл бұрын
Your welcome!
@OutsideCleaners
Жыл бұрын
Great video
@ExtremeDIYGuy
Жыл бұрын
Glad you enjoyed it!
@leemonk7760
2 жыл бұрын
Great videos! Did you move the seat/console assembly forward 5-6 inches? Im considering doing that with my 13' as I'm putting it back together after painting it.
@ExtremeDIYGuy
2 жыл бұрын
Yes I did, it helps with the weight distribution.
@_noname617
Жыл бұрын
New sub, thanks for sharing mine's going in tmrw #cheers
@ExtremeDIYGuy
Жыл бұрын
Good luck!
@guyclement1732
3 жыл бұрын
Nice video, but did the same on my little 15' Key West and now the steering turns in oposit direction, when turning right the boat goes left or turning right the boat goes left. How do I fix the problem?
@ExtremeDIYGuy
3 жыл бұрын
I would move the cable to the other port on the helm, I believe that should fix the problem.
@BennettBarry
3 жыл бұрын
Great video! Thank you!
@ExtremeDIYGuy
3 жыл бұрын
Thanks! Much appreciated!
@buroakridgehomestead5995
11 ай бұрын
I’m planning to do this project on my 13. What is your preferred steering wheel to replace the OEM white one?
@ExtremeDIYGuy
11 ай бұрын
Completely stainless, Doesnt matter what type or number spokes to me
@BGS002
3 жыл бұрын
you mind confirming something for me? is the angle on the face of the console the same 105 degrees as the seatbacks? i'm planning to build my own super sport deluxe style interior for my '78 15 footer. keep the videos coming they've been extremely helpful!
@ExtremeDIYGuy
3 жыл бұрын
I checked earlier and both sides 20 degrees.
@cgmax9830
3 жыл бұрын
Are you sure the steering gearbox bolts were 85 ft lbs torque?...that seems excessive. Great video, though...I did this to my 11 ft Whaler last Fall.
@ExtremeDIYGuy
3 жыл бұрын
Yes, the instructions called for a range of 75-100 foot pounds.
@cruzerfj4060
3 жыл бұрын
What length cable or part number did you use for your 11 ft? Contemplating doing the same on my 11 ft T/T.
@cgmax9830
3 жыл бұрын
@@cruzerfj4060 I used the smallest cable avaliable...it was 8 ft from Defender marine.
@embededfabrication4482
2 жыл бұрын
is that going to work on my 14' aluminum, I saw someone put it on their 10' tender, must be enough room to bolt it to the transom on a small boat. The "safe-T" version must mean no feed back I guess
@ExtremeDIYGuy
2 жыл бұрын
I don't see why it wouldn't as long as you have somewhere solid to mount it too.
@shaunmcinnis1960
3 жыл бұрын
Nice video
@ExtremeDIYGuy
2 жыл бұрын
Thanks
@alfredodelamerced100
3 жыл бұрын
Did you mention how far your console is from the rear of the boat?
@ExtremeDIYGuy
3 жыл бұрын
I'll have to check as the boat is currently packed up cornering but I'll get back to you on that.
@alexnutcasio936
2 жыл бұрын
What was length of the Teleflex cable you used?
@ExtremeDIYGuy
2 жыл бұрын
If I remember correctly it was 13'
@JohnDoe-wm9lr
2 жыл бұрын
In the video you said 11ft cable
@ExtremeDIYGuy
2 жыл бұрын
@@JohnDoe-wm9lr Go by what I said in the video. I have crappy memory
@JohnDoe-wm9lr
2 жыл бұрын
@@ExtremeDIYGuy Where did you get the interior from? I'm looking at building one, but I'm having trouble finding plans and dimensions. Looks pretty simple if I had some measurements lol.
Пікірлер: 47