I installed a 12000 S winch on my gladiator. On the square nuts that are in the winch, i used duck tape to hold the nuts in.
@ambrose.little
6 жыл бұрын
Hi Damon, thanks a bunch. Your video and tips helped, especially to beware of the unexpected challenges. A few notes. I found that keeping all the bumper bolts loose, pulling the bumper out a bit, and threading the inner ones on worked-there was enough room that way to get them by the winch. It is still a SUPER tight fit. I bought a battery power ratchet in anticipation after you mentioned how much of a PITA it was. That made it go a lot faster, though it was tough squeezing in there. Used extensions of different sizes. Also ended with torque wrench so would be spec (66 ft lb). The skid plate was as you mentioned a challenge. I left the brackets loose and banged on them down/toward the front, then tightened. That seemed to get ‘em close enough so I didn’t have to drill. I spooled the winch after putting it in the plate; gave me something to provide a little tension with. I also managed to get the winch nuts in after placing it, so I didn’t have troubles losing them. Anyhow, still a longish project for me, but your vid helped prepare me, so thanks again!
@keithewy9396
6 жыл бұрын
Very nice video! That inside top bumper bolt is a bugger. Off to the hardware store I go! The two farthest-in skid plate bolts can line up without drilling by inserting a large screw driver in the adjacent holes and prying until the bolt hole lines up with the welded nut. Surprisingly that plate has a bit of spring flex to it where it curves! Of course all other skid plate bolts must not be tight. Thanks for the video.
@JulioSalazar-xw7np
4 жыл бұрын
This is the winch model that I need for my JL and I got the same front bumper as yours. My next project will be electric stealth step bars and a roof rack. Thanks for this video!
@jodymartin9898
4 жыл бұрын
Tip: take off the grill. this made reinstalling the 8 bumper frame nuts easy. it's tight getting the grill back on behind the winch afterwards, but if you start with the bottom clips into the metal frame and go slowly..........it works.
@Saudiprint
5 жыл бұрын
New JL Rubicon here in Saudi too, and sure it is a legendary Car! After your nice video, I am gonna get my winch installed too. Thanks for the great video.
@jimharr
Жыл бұрын
Those inner bumper holes were a bear. I put a jack under the winch plate and shifted the winch over, centering it. This gave me enough room for access to get the nuts started.
@lynnbburkhart2945
6 жыл бұрын
Well, after seeing your videos I bought the same color rubicon you did. Now, here I was looking for a winch and bingo - here’s your winch video!
@DamonBungard
6 жыл бұрын
awesome!
@user-ud2mk5hj7b
6 жыл бұрын
New JL! Jeep it's legendary vehicle! I'm from Russia.
@crispbacon5806
Ай бұрын
Hey buddy! Still alive?
@JamesTexas
5 жыл бұрын
Super helpful video. Installed mine today with the help from a friend and by watching your video. I was able to use the original nuts with the flange. I also had to widen the holes on the skid plate to get the screws to line up. Thank you
@Ebbyman413
5 жыл бұрын
Very helpful video with a lot of 'heads up' for the pitfalls you ran into - I too had trouble with the inside upper drivers side nut. I took the nut to a grinder and removed the flange from the backside of the nut to get it to fit around the winch.
@schoocg
6 жыл бұрын
Success and it wouldn’t have been so without your vid and other tips you typed below. Your points of NOT tightening the 8 bumper bolts until you have threaded the 4 inside bumper bolts first and also re-attaching the 2 screw/bolts at the end of the skid plate before all 8 bumper bolts are torqued down . Without those tips things will not go together as the instructions say. They need to add those two critical points. Thank you for these critical points!!!! And once installed, wow, what a great fit and look. And for anyone else reading these comments 5/6/18, as far as I can tell as of this date only WARN is making a bracket to fit the Zeon to the factory JL steel bumper. Last week I could not find any WARN brackets, everyone was sold out. Quadratec swore they had a Rusty’s bracket that would work. Well it does NOT. Yes it fits the new JL steel bumper but not for the Zeon winch. I called Rusty’s and they confirmed to me it would not work. Great, got experience taking the bumper off and back on:-) I finally found a WARN bracket for the Zeon to fit the JL from NorthRidge4x4 and they sent additional online installation instructions with great picts. Also, they mention not putting on the fair lead till last. Hmm, I found that not to be a good idea. Putting on before installing the bumper a much better deal. Don’t understand why they recommended that. Besides an amazing fit and look it is going to be one extremely difficult winch to steal..the thieves better be well prepared and tooled, and lots of time trying to figure how to take it all apart. You can’t lift it straight out of the bumper.
@DamonBungard
6 жыл бұрын
glad it was helpful!
@claudeperrault4164
5 жыл бұрын
Excellent instructions! Easy to follow! Will be helpful when I get my 2019 Wrangler Rubicon in 6 weeks! Thank you!
@LanceMcCollough
4 жыл бұрын
Hi Claude, did you end up mounting this winch on your 2019 Rubicon? Any issues?
@LarryRichelli
3 жыл бұрын
Was hoping to see how the license plate worked
@sarge502jeep
2 жыл бұрын
Very well put together install vid. I’m helping a friend run this exact same setup soon (Warn plate and Zeon 10-S). Just ordered the other day. Hopefully all runs smooth. Gonna go ahead and pick up a swivel adapter for those tricky bolts. Other than that seems pretty straight forward. I’m gonna try to attempt this without widening out the two rear winch plate holes. We’ll see.
@edwilson9243
6 жыл бұрын
Great step by step, have the same jeep. Going give it a try this week, same winch thanks
@schoocg
6 жыл бұрын
Thanks for the great tips. I put mine on in next couple of days.
@DamonBungard
6 жыл бұрын
The key for getting that tough interior nut back on is to start it before the bumper is fully re-inserted back onto the frame. Just barely get the bumper re-mounted so the threaded studs are just able to be engaged by the nut, and tighten it while basically pulling the bumper back into place.
@tunesoulsata9251
6 жыл бұрын
Great video! Keep them coming my brother!
@seths.9180
4 ай бұрын
Great video ! Were you able to get the skid plate back on. I'd greatly appreciate tips on how to reinstall the skid plate.
@DamonBungard
4 ай бұрын
I was, but I had to elongate the holes slightly with a drill bit
@scottxb
6 жыл бұрын
Great video - awesome detail. Thank you!
@RabidNomad
6 жыл бұрын
Thanks for the HOWTO. Was looking for this exact same setup here.
@owadog
6 жыл бұрын
Awesome! Thanks for sharing, I was just looking for a video on this. I can’t wait to do this myself. I like the fact there’s no drilling the bumper at all. I have the same steel bumper and I was wondering if I would have to do any drilling. I’m also glad there’s a license plate adapter/holder as well.
@michaelozment9896
4 жыл бұрын
Thanks for making this video. It was very helpful!
@davebishop9954
2 жыл бұрын
Your Step by step video was A-1. Question: after removing your factory skid plate to allow for the winch plate installation it left your sway bar disconnect actuator assembly exposed to potential damage. Is that ok with you? Thanks for the vid.
@sarge502jeep
Жыл бұрын
So I have a question that nobody has really covered in the many Warn winch install videos I've watched. But why on the bumper is it suggested to remove the fog light wiring from their connectors? Not really sure why that is needed unless it interferes with the plate. But even then how does it get put back in that case.
@mattdonaldson4439
7 ай бұрын
Was there any particular reason you decided on the Zeon over the Evo?
@thelateresponder-tlargh8591
Жыл бұрын
Solid install job instruction, thank you! This may be a dumb question, but is the official Warn 10-s winch cover able to fit given it sits so snugly in the bumper? About to do the same install myself and have held off ordering the cover.
@jackd7402
3 жыл бұрын
Great Video! Request part info on your license plate bracket.
@ward4251
2 жыл бұрын
Was your winch plate angled downward to some degree?
@davidstreet732
5 жыл бұрын
Great video. Any idea if that set up would work without those spacers installed? Thanks.
@rxtu7367
2 жыл бұрын
Does this kit include the fairlead?
@355free
4 жыл бұрын
Question. Why did you need to pull the LED wiring harness clips before reinstalling the bumper? Checking before installing one myself. Thx.
@SPLTDP
4 жыл бұрын
Had trouble getting a SmittyBuilt XRC Gen 3 Fairlead and Warn Filler Plate installed on a JL with Steel Bumper and The Warn Winch Plate. The Bolts were two short two mount the Fairlead and Filler Plate. I got longer Bolts but the Fairlead and Filler Plate had some up and down play. Did you notice that? I’m worried that under load the Fairlead could slip down and then the rope would be on the rough edge of the plate. I see in your video there is what appears to be a bolt coming through the back of the bumper where the filler plate and Fairlead will be. What is that? I don’t have that? Thanks for any help!
@RoundTopJohn
5 жыл бұрын
I have the same winch and bumper. Have you figured out a way to replace the winch rope when needed? Hope it can be done without removing the bumper. Sure looks nice.
@schoocg
6 жыл бұрын
Thanks for the great tips.
@edendriga446
6 жыл бұрын
Great informative video.... Thank You....
@irishcherokee8884
5 жыл бұрын
Great instructions, thx.
@mtutone
6 жыл бұрын
Love your Jeep. Great Vid.
@jvanostran50
3 жыл бұрын
You mentioned that the winch was “JL Ready” I haven’t seen anything in Warn’s literature where you can designate that. How did you make sure that it would fit the Jeep bumper
@DamonBungard
3 жыл бұрын
this video is from a few years ago and what made it 'JL' ready was throw lever turning just 90 degrees when they had been turning 180 degrees. They needed to change to 90 degrees to prevent interference. At the time Warn was shipping them with an added sticker on the box. I'd imagine that by now they just make them all with 90 degree levers.
@Nick-gi6ym
6 жыл бұрын
I think the warn winch co should have planned the install better they messed up not right you had to drill & auto part store to complete your install. Great Job
@sticrzy123
3 жыл бұрын
I have this JL rubicon with the steel bumper , my question is how strong is it when using the winch , I’m assuming they did there hone work for super strong but just curious
@ronwackford9720
5 жыл бұрын
Very nice vid. Thanks!
@jondrew55
5 жыл бұрын
Great video. Just got a 2018 Rubicon and some guy locally has a Zeon 10S for sale used and the plate for his 2018 Rubicon. But I have a plastic bumper, so I assume I’ll have to buy a bumper too? Or will it work (with cutting) on the plastic bumper? I literally got this Jeep a week ago so I have not had time to research winch/bumper combos, but this seems like a good deal on the S10 so even if I need additional stuff, I may pick it up and install later.
@liaodesign
6 жыл бұрын
Very detail video but removing the bumper seems a bit too much for me not very good with fixing my own car thanks for the great video
@davebishop9954
2 жыл бұрын
Sorry but I realize now you did get your skid plate back on. Your sway bar disconnect assembly will be protected.
@Retro64XYZ
4 жыл бұрын
What were those jack things you use to lift the vehicle? The ones you drove up onto? Can you link to those for sale somewhere?
@jahovh1108
5 жыл бұрын
Where can I get the spacer license plate bracket could you share link please?
@thebigbail
2 жыл бұрын
I’m waiting on delivery of my winch… just wondering if you think it is possible to tighten the bumper bolts and then drop the winch into place?
@DamonBungard
2 жыл бұрын
unfortunately I don't think that would work
@markdarnell2792
6 жыл бұрын
Did you add a 3/4” spacer to the front to offset heavy Winch weight or measure to see how much it sagged the front?
@DamonBungard
6 жыл бұрын
i did not add a spacer to the front, and measured no notable sag after installation.
@mrchams
4 жыл бұрын
Did you notice the additional front weight while driving and cornering after installing the winch?
@DamonBungard
4 жыл бұрын
not really -- with it being a synthetic winch line, that's much lighter than steel (and I did notice the weight when I added a steel winch on my old JKU Rubicon)
@brentb9823
6 жыл бұрын
In another video you spoke about 4” rock rails you bought. Could you please send me the website for that?
@DamonBungard
6 жыл бұрын
I bought mine direct from the parts department at our local dealership using a Mopar coupon, but here there are at Quadratec also: www.quadratec.com/p/mopar/performance-style-rock-rails-jeep-wrangler-jl
@vegasdavetv
6 жыл бұрын
nice job
@miken9484
6 жыл бұрын
Looks good 😘
@DUNEATV
3 жыл бұрын
I’m trying to understand why you removed the bumper to install the winch?
@DamonBungard
3 жыл бұрын
removing the bumper is required, there's not enough opening on top just lower the winch down in. Warn has good instructions outlining each step.
@DUNEATV
3 жыл бұрын
@@DamonBungard Oh, I thought it could just slip down it after removing the top plate..
@EmirEscalante
4 жыл бұрын
Hello. By chance, do you have a link to where you got the JL-ready Zeon 10S? when I look up that part number, the screenshots do not show if it is "JL-ready" or not. And that 90 degree lock shows a 180 degree turn instead. Thanks.
@DamonBungard
4 жыл бұрын
I do not, but call Warn customer service. they are very helpful
@erlegree
6 жыл бұрын
FYI That exact same bumper was available on the JK Rubicon.
@schoocg
6 жыл бұрын
I am not exactly for sure but my suspension is that fitting winch brackets for the steel bumper differ between the JK and JL. Thus all the fuss trying to get a Zeon to fit the JL and finding a bracket that will work. As of 5/6/18 the only bracket I found that works is the recently released Warn bracket. I even contacted Rusty’s and they had not released their bracket for this configuration yet.
@josorzo11
5 жыл бұрын
You think the Zeon 10 s non JL ready would got fit ? I have one but the lever moves all the way around , I’m think just cutting a little bumper . What u think?
@DamonBungard
5 жыл бұрын
You need to call Warn customer service and they will send you the upgrade kit that changes your lever from 180 to 90 degrees rotation.
@saadalqarni4275
6 жыл бұрын
؟Great video... but what about the plate
@ifp123
5 жыл бұрын
U.S.A. State specific! In Maryland, that can be a $110. citation
@alphadata3652
5 жыл бұрын
Off road lights?
@outlander7717
5 жыл бұрын
nice jeep. I test drove a 2018 rubicon at the local dealership today(Columbus Ohio) with 17k miles on it.The sticker was 40k....Is that the going rate or are they being greedy?
@slothhunter4615
5 жыл бұрын
You might check out cargurus.com it is a really good sight for getting the best deals on your jeep or whatever vehicle you are looking for
@1uptospeed
6 жыл бұрын
great vid. was wondering what kind of city & highway mpg you get? is yours a 8 speed auto?
@DamonBungard
6 жыл бұрын
Yes, automatic, and I get around 16-20 city/hwy.
@stustamps5416
5 жыл бұрын
is the winch plate the same for the JL Rubicon 2 door as it is for the 4 door? I have the 2018 JL Rubicon 2 door
@DamonBungard
5 жыл бұрын
I don't know, but if you call Warn Customer Service they are very helpful and will be able to tell you
@alanreyes9395
6 жыл бұрын
Will the warn zeon 10s platinum fit? I dont know if there is a size difference between the manual clutch or platinum
@DamonBungard
6 жыл бұрын
I don't know, you'll need to look at specs on the WARN website. If outer dimensions are the same, yes, it should fit. Or call their customer service line, they are very helpful
@alanreyes9395
6 жыл бұрын
Damon Bungard thanks!
@schoocg
6 жыл бұрын
Yes it will. I just installed the Zeon 10-S Platinum. It has the same dimensions as the normal Zeon 10-S. It uses the same WARN bracket.
@alanreyes9395
6 жыл бұрын
schoocg thanks!👍
@rkwilliams56
6 жыл бұрын
Will this mounting kit work on my 2016 Jeep 75th anniversary addition. Looks like the same bumper.
@DamonBungard
6 жыл бұрын
best would be call Warn Customer Service and find out.
@daveward6348
6 жыл бұрын
Just installed it on my 2016 Jeep Rubicon Hardrock 75 Anniversary Edition and it fit like a glove. Didn't run into any problems on the skid plate, and a 18mm Box wrench got those hard to reach nuts.
@leefastenau9890
5 жыл бұрын
So the bumper isnt winch ready?? You gotta buy a winch plate?
@DamonBungard
5 жыл бұрын
yes, you'll need a winch plate as part of the mounting kit. It's 'winch ready' in the sense you can mount a winch in it without having to replace it, but you do need the plate.
@BrodyToYou
5 жыл бұрын
I’m thinking about putting a 3.5” lift and 37’s on my JLUR, but how can I keep them from sticking out so far?
@bajamedic
5 жыл бұрын
Where did you buy the hood protector?
@DamonBungard
5 жыл бұрын
BajaMedic I made it myself with Plasti Dip
@XTMZ
6 жыл бұрын
God jop
@froshproductions
5 жыл бұрын
What kind of gloves are you wearing?
@DamonBungard
5 жыл бұрын
Those are the Shooter Gloves from Sitka Gear
@artgeo5639
6 жыл бұрын
Hey Damon were you able to get the 4 inner flange nuts on? I had the same problem and it could be done, it just takes time. The Zeon 10s has to be on there loose. you need to push it to one side. Then slightly tilt your bumper up and start the inner top flange nut. The flange nut has to be in front of the winch. You'll need a short socket to start and a swivel or flex drive. Let me know how it turns out. . . .
@DamonBungard
6 жыл бұрын
I was eventually able to get that 4th nut, but I had to get a nut without the flange on it
@ghorman1
5 жыл бұрын
Damon Bungard do you remember what nut you purchase? I have everything together but that nut.
@joedanna1952
4 жыл бұрын
If you have common sense it's a decent walkthrough to show you the stepsbut I highly recommend watching a few other ones before you attempt the same installation all the problems he had could have been avoided
@kingofkings6242
3 жыл бұрын
man you skipped the skit re-install part , that's a major issue in installing the winch plate
@alchavezjr410
2 жыл бұрын
Winch looks amazing but for 3K ill pass!!
@losersquadhd1234
4 жыл бұрын
Yo you could also just let a jeep dealer do it for you, I know that its not the most manliest thing in the world but if you aren't comfortable or are afraid that you might brake it, then let Jeep do it for you.
@kramernaylor7810
4 жыл бұрын
I'll let my jeep dealer do it for me. My condo doesn't allow mechanic work and my friends aren't mechanics either
Пікірлер: 109