Thanks for providing thorough instructions. So many videos claiming to replace a water pump without replacing the entire pump. You helped were others failed.
@HouseOfThe8Strings
4 жыл бұрын
Doing this exact same job. Best video on KZitem. Thanks.
@buddyjohn
3 жыл бұрын
OMG this was hilarious thk u so much. Basically a what not to do video lololol like this, no wait like that no what lolol dude stick to what ya know best, chokin gaggin vommiting etc and remember kids: smoke up johnny...🤣
@mel2734
3 жыл бұрын
Bwwhahaha .your good man thanks for let us know buddy John's a tool .lol you're the best 👌...but you better get you some cream for the butt hurt 🤣....
@mel2734
3 жыл бұрын
I even gave you a sub with your big KZitem channel..good luck man
@yrrall123
10 жыл бұрын
Good job. Just doi9ng the same thing on 1967 650. Helped a lot man.
@mel2734
10 жыл бұрын
Glad I could help you out. Good luck on your fix.
@j.bryanfloyd4933
9 жыл бұрын
godamn yall must be rock jumpin in that thing bro!!! lol...that prop and skeg are toooooast!!
@kennethlapointe1165
9 жыл бұрын
To put the water pump replacement into the upper unit get a 2-1/4 " water hose clamp screw it smaller until it is the same size as what you will put it in, have all the fins going the right way and just slide it out. (works great and is easy)
@Armando-ou2vj
5 ай бұрын
Thanks bro you saved my azz🫵🏼💯🦅
@arijaaksi
4 жыл бұрын
Thanks! This was helpful. Now, around 21:40 you can see a small pipe/hose at the left hand side of the video coming out just above the lower part of the upper part of the motor. I've got the same thing and it is not connected to anything. What is it? What's the purpose of that little pipe?
@mel2734
4 жыл бұрын
Im sorry i couldn't tell you . its been a long time ago ... You maybe able to find a book on the part online somewhere .. Again im sorry for not knowing ..
@joshherngk
4 жыл бұрын
Perhaps, you are referring to the speedometer hose.
@arijaaksi
4 жыл бұрын
@@joshherngk Maybe. Mine doesn't go anywhere -- but then again, I don't have a speedometer. It looks like a little water pipe, though.
@makexu5616
5 жыл бұрын
What is the nameplate fuselage number of this pump set for hanging machine? Thank you very much
@jamesbaucom9538
2 жыл бұрын
I have the same motor and replaced the water pump but it still does pee. I took it apart to check everything and didn’t see anything wrong. What else can I do?
@mel2734
2 жыл бұрын
The only other things I can think of you may have the rubber fins facing the wrong way and it not sucking the water up ... or you may have a blocked water line . Here in indiana we have these bees called mud daubers they will build their nests in the water lines of the boat motors blocking the water from coming out
@mel2734
2 жыл бұрын
@james baucom
@yourselfdotcomlol
5 жыл бұрын
That prop be looking haggard as fuck. Otherwise your video is completely on point. Good advice. All the finer points of doing the job. Touch of spline lube never hurts the shaft bro. Stay safe
@RonGallardo777
9 жыл бұрын
great video showed step by step ...and thanks to your video I could find the two rubber cap link showed at 20:15 ..bcaus it was stuck in the way and I had to go fishing it in the leg of the motor
@mel2734
11 жыл бұрын
your welcome... I hope it helped you out
@mattsimmons6877
4 жыл бұрын
I don’t know if you guys found it or not but when you pull the driveshaft out the engine you pulled off that little plastic piece that sits on the spline there is actually a Nother one that sits on top of the plastic piece that butts up against the bottom of the engine. They normally fall off when you pull it out and it gets stuck up in there
@walterlopez5343
8 жыл бұрын
Where does the black rubber hose (water line) hook up too. I just bought a model similar to yours and it's missing the black rubber hose so I bought one. I need to know where to hook to the top portion.
@mel2734
8 жыл бұрын
if i can remember right its a small brass tube at the top housing. the water line presses on to it. i hope that helps you out.
@walterlopez5343
8 жыл бұрын
+mel2734 Thank you. I've been doing research on that black hose and it's for the speedometer. It seems like you can cut and cap it if you're not using it.
@scottwhitefishing
8 жыл бұрын
+Walter Lopez (mobowhunter77) Yes that's what is, they're pretty much useless and inaccurate. Mercury has had them on their outboards since the late 70s I believe. I've got an 84 35 HP that the lower unit is pretty much the same same as this 98. My 97 40 horse is the same as well.
@zaneturner4478
6 жыл бұрын
I know this is an old video but for anyone using this as a guide the only thing missing is the fact that there is a inner seal in the lower half of the water pump housing besides the oring on the outside that should have been replaced, it keeps water from getting into the lower unit as well as keeping the lube in the unit.
@สุรศักดิ์กุลเมฆา
2 жыл бұрын
สน
@gerbs304
3 жыл бұрын
CAUTION!!! READ THIS BEFORE ATTEMPTING THIS JOB!!! Hey Guys, Thanks so much for the video, I have an 87 model 35hp that I need to do this job on also... The only problem I can see is your use of Petroleum Jelly! What I figured out by working on my own Hot-tub is that using pet jelly makes rubber parts/seals GROW and become soft/pliable!! So I asked the dealer when getting an O-ring (for the 2nd time) because the 1st one had grown, making it impossible to reinstall it... he said vasoline is a big no-no with rubber parts for all of those reasons. Use SPRAY SILICONE OR SILICONE GREASE ON RUBBER PARTS, VASOLINE/PETROLEUM JELLY WILL DEGRADE RUBBER PARTS!!! I'd be willing to bet that he had problems with his water pump not long after this job for that reason! I would think that the impellor probably swelled and got soft and probably ripped/ deteriorated making water movement impossible... I only hope he redid the job with silicone grease, before he blew his motor up!!! (Otherwise, good job on the mechanical part of the video!!)
@mel2734
3 жыл бұрын
It still works to this day and passes water like it should .even the paper work for the water pump impeller said you can use petroleum jelly or any other water repellent .
@mel2734
3 жыл бұрын
@@woodchipgardens9084 i want to say it did. its been along time ago and I can't remember
@mel2734
11 жыл бұрын
I picked my kit up at a small boat store in Monticello ,in by the lake sorry I cant remember the name if I find out ill tell you ...sorry it took so long you get back to you
@Seawood77
8 жыл бұрын
Great video! Have the same motor and this was a big help. Thanks!
@mel2734
10 жыл бұрын
You're very welcome glad the video helped
@xgi36
10 жыл бұрын
Thanks for the video. Very helpful.
@1porsche965
11 жыл бұрын
Excellent. Thanks for taking the time to post. I'm going to give mine a try next.
@Huckaby
9 жыл бұрын
Thanks for posting this, my motor needs this fix - in pieces now. I got water out of the 'pee-hole' for about 2 minutes this year - then steam only. Not good. One tip I saw in another video was to install the water tube in the motor side first when reassembling. I have not found the cuff-link and gasket you mention at 20:15 - need to fish inside the motor perhaps. Anyway - hopefully, I'll be motoring this weekend. Thanks!
@Huckaby
9 жыл бұрын
Jason Huckaby OK - an update. I found the spline seal and the piece below inside the motor housing. The spline seal (upper part) was trashed and was not easy to remove (had to be pulled) - it was torn to pieces. Motor still in pieces - putting water tube in first does not seem to be any easier. In fact, reassembly of the lower unit is a PIA, Just FYI, for anyone else attempting. If you're doing this, spline seal will probably need replacing too.
@Huckaby
9 жыл бұрын
Jason Huckaby Done! Not run yet, but all went mostly smoothly. You may have your shaft seal on upside down, in reviewing the manual - it shows it the other way (wide funnel up - narrow on bottom). Installed water pipe in motor first - the only way I could get it together.
@billmansfield8654
4 жыл бұрын
What does the top of the water tube go into I don't see where it fits into
@OhEmmJesus
12 жыл бұрын
You always want to put Rubber on your shaft! Ha
@kwstasviole6609
8 жыл бұрын
tnks for the vid i lern math
@kylekrist7122
12 жыл бұрын
ive got the exact same outboard and i cant find a replacement kit can u tell me were u got yours
@j.l.daltoin2238
6 жыл бұрын
Sierra kit 18-3207 kit comes with impeller and o'rings and gaskets to fit1980s 35hp mercury mine is a 1985 good fit on parts the trick is getting the gear shift and the camshaft in right so if you get it wrong you will have neutral and forward only if you get wrong the other way you will have neutral and reverse and no forward took me 1 hours to get it right again lolo so watch that shifter is in neutral and the cam in neutral when you put it back some may tell you another approach to this so look on you tube for that
@mel2734
12 жыл бұрын
oh yes you do lol
@swampswag69
10 жыл бұрын
Would a 99 20hp mercury 2 stroke be pretty much the same?
@mel2734
10 жыл бұрын
I'm not sure it may work .sorry I couldn't tell you .
Пікірлер: 51