Be sure and check the video description for links to items used in the video.
@cochase
Ай бұрын
Man you are doing the most for these trucks I just picked up an insanely clean one that sputters a bit and the previous owner said he replaced fuel pump and fuel filter, runs decently now but still has stock carb with 118k miles on it and cant wait to tackle this because of you. My confidence with it is through the roof and it'll be my first time replacing a carb not on a lawn mower lol, thanks Mitch!!
@thecuss6817
Жыл бұрын
Nice. I've been running genuine Redline Weber in my B2200 since 2005. I also used Permatex Aviation (no RTV). I needed a stronger return spring, and real good vacuum caps too. I used blue Loctite. Lower adapter to the intake manifold gets torqued to 12 ft lbs; upper adapter gets torqued to 6 ft lbs (72 inch lbs).
@poopl00p3r
Жыл бұрын
So ur saying ur down to start a band and ur truck can haul speakers, equipment, etc, & hoes.
@spankylowkz2480
Жыл бұрын
Are you the famous Chino cusser ?
@thecuss6817
Жыл бұрын
@@spankylowkz2480 That's me - but not famous!!! Facebook made me have two names when I signed up...why I couldn't simply be "Cusser" or "Cussboy".
@spankylowkz2480
Жыл бұрын
@@thecuss6817 ahhh I see Cusser, well you’ve helped me a lot on Facebook with your tips on running Weber Thank you .
@Loganstonez
Жыл бұрын
I dig your attitude and straightforward videos. Thanks for makin em
@MazdaMitch
Жыл бұрын
Glad you like them!
@yenkie64
Жыл бұрын
Videos becoming better and better each one! Keep up the good work
@MazdaMitch
Жыл бұрын
Thanks! Will do!
@STRIKO04
Жыл бұрын
I wish I could do this here in SoCal. Diggin' the video
@seafarerbones3465
4 ай бұрын
I’m in SD and I’m doing it. Gotta do what we gotta do! You can do it.
@poopl00p3r
Жыл бұрын
MITCH. lets start a rock bank. i play bass. ill drive over there in my b2200.
@MGB-learning
10 ай бұрын
Great video!
@mattblack9344
Жыл бұрын
Hi Mitch. Is there a part number for that carb. Cheers. Great vid.
@MazdaMitch
Жыл бұрын
Always check the video description there's links there
@508boricua
Жыл бұрын
Can you share a link on where to best purchase a genuine Webber carburetor? Great vid as always. ✌🏼
@MazdaMitch
Жыл бұрын
There is a link in the video description.
@MattCodeIT
2 ай бұрын
Hey, I have a mazda b2600 I think but am not sure because it was abandoned in my granfathers farm. Are there any major difference in the carburetor needed between the 2200 and the 2600 or will either work? thank you!
@MazdaMitch
2 ай бұрын
Most of the 2600 are fuel injected. If you happen to have an 86-89 2600 it could be carbed, and there is a kit fo that.
@hermintrinidad9868
10 ай бұрын
Mitch I like the what your doing thanks like the music can you share the name of the group & song.
@MazdaMitch
10 ай бұрын
Which one? What time in the video?
@JoeBribem
9 ай бұрын
That bowl vent doesn't need to be open to atmosphere huh? I've always suspected mine to lose its fuel prime and in need of a check valve before the carb. Please advise.
@MazdaMitch
9 ай бұрын
The bowl is venting directly up through the top into the air filter area.
@cardozaslegacy4163
3 ай бұрын
Where did you connect the red cable too??
@MazdaMitch
3 ай бұрын
Over on the passenger side fender well when we got rid of a lot of the unnecessary things we kept a few of the plugs that have a 12 volt power when the key is turned to the on position and that's what we used
@cardozaslegacy4163
3 ай бұрын
@@MazdaMitch thanks
@omarcamargo517
11 ай бұрын
Hey mitch I have an 86 b2000 and it smokes a lot in the morning and when i park it for couple hrs
@MazdaMitch
11 ай бұрын
Sounds like it could be the valve seals.
@hondaman9980
Жыл бұрын
What head gasket would I use if I put a 2.2 head on a 2.0 block
@MazdaMitch
Жыл бұрын
You always use the head gasket that matches the block you were using
@hondaman9980
Жыл бұрын
@@MazdaMitch okay, thank you very much does it matter which cam gear I use? I know the timing belt is different because the 2.2 has an extra pulley
@amosburt1324
4 ай бұрын
How bout a pressure regulator? I’ve ran webers for years and never ran one, any other thoughts on the matter?
@MazdaMitch
4 ай бұрын
If I only had a dollar every time I heard that question.... Does not need one. The mechanical fuel pump doesn't put out enough pressure. No worries
@Piston206
6 ай бұрын
I have a new electric pump installed close to the fuel tank as it supposed to and I’m getting the 3 psi with the fuel regulator but after a couple min pressure decreases. Does that has something to do with the carburetor? Be cause later the Pressure picks up again Thanks
@MazdaMitch
5 ай бұрын
Not many of us use a regulator. Your pump may be weak and your regulator redistricting too much. I have a video on my channel showing how we went from the electric pump to a tried and true mechanical pump. Works better. kzitem.info/news/bejne/yoahrmyChJqZf2ksi=_T3vBjysVrS58nzF
@ozzzy41
Жыл бұрын
MItch can you share the size of the bolts you used for the plates and where to buy them, thanks
@MazdaMitch
Жыл бұрын
It all comes in the box in the kit
@MazdaMitch
Жыл бұрын
And there's four bolts that you use from the old carburetor
@redtailhawk289
4 ай бұрын
Blue lock tite is easer to remove . I hope you don't. have to take it back off .
@MazdaMitch
4 ай бұрын
I use red all the time and trust me it don't hold as good as you might think. I've gone back in to do this and that and it's not hard to remove but better than nothing
@LostBoy1026
10 ай бұрын
Hey Mitch great video, I have a question I can't find you on Facebook yet. I installed a weber 32/36 and it runs ok. Choke might be a little off But almost every time I go to shut the truck off it continues to run for a few seconds like 3 seconds. It didn't start doing it until I put the weber on the truck. Any Ideas? I could really use your help if possible. I don't know whats causing it? Thank you
@MazdaMitch
10 ай бұрын
It's probably dieseling. Idled up to high. Really need a tach to see where you are. It's probably idled up too high.
@LostBoy1026
10 ай бұрын
Thank you
@howdy4596
8 ай бұрын
Where did you get the breather for you truck? Is that the actual name? I can't find d one when I search breather for mazda b2200 .
@MazdaMitch
8 ай бұрын
It's called a ramflo air filter for the Weber carb. I forgot where I got it from.
@howdy4596
8 ай бұрын
@MazdaMitch thank you . Looking for one now.
@WalkinGHeAteR77
8 ай бұрын
I put a new 32/36 Weber carburetor on my 1989 Mazda b2200 and for some reason when I’m driving at 55 mph there’s a loud talking noise with power going down could it be possible I need to august the Weber ?
@MazdaMitch
8 ай бұрын
It's probably something else and not the carb at all.
@Kro_man_tx
Жыл бұрын
Did you learn anything from the video that came with your carb?
@MazdaMitch
Жыл бұрын
Nothing I didn't already know The video is up you can watch it here.
@wheelspkruel
Жыл бұрын
How is the mpg with the Weber? Is it better or not? Or what’s the different on oem vs Weber?
@MazdaMitch
Жыл бұрын
I have a few videos 9n here showing me getting 27 mpg. I get that on 5he hwy consistently regardless of season. Usually doing 70mph and ac on in summer.
@MazdaMitch
Жыл бұрын
What's better about the Weber vs the stock carb is a lot less bullshit to deal with and less bullshit that can go wrong. Easier to maintain, a little more hp and mpg at the same time.
@wheelspkruel
Жыл бұрын
Nice man thanks again for teaching us how to work on this trucks
@WsykeyMalone
Жыл бұрын
After my mazda has been sitting for 4 yrs is it kinda normal for it to blow smoke when it starts up do you think once I get it tuned up it will calm down
@MazdaMitch
Жыл бұрын
It may, but it could easily be the valve stem seals. When things are not used often the seals are not lubricated and break down
@Soldevi89
Жыл бұрын
Is this the same truck you did the valve seals on?
@MazdaMitch
Жыл бұрын
Yep, we did the head gasket and cylinder head rebuild on this truck. This was after those videos
@garrett-dr5rc
Жыл бұрын
Can you send a new link for this carb
@MazdaMitch
Жыл бұрын
Should be in th video description
@garrett-dr5rc
Жыл бұрын
@@MazdaMitch it says unavailable for me
@MazdaMitch
Жыл бұрын
@@garrett-dr5rc Here try this, says backordered for months. www.carburetion.com/Products/ProductDetails.aspx?part=K675&fbclid=IwAR2_xtI55Zs9YIDNX8zUGKTN5-O9IG1KzS_qSkxGQjMAtWTJRQDTu9cGU58
@user-mq1kd8ll3b
Жыл бұрын
How can I get a carburetor for a 1984 Mazda B2000 pickup? Can I get it with you?
@MazdaMitch
Жыл бұрын
I'm just a KZitemr sharing my experiences I'm not a wholesaler of carburetors. Links are in the description go to those websites and look up your model needs
Пікірлер: 66